ERGONOMIC EHL Manuel utilisateur

In-Line Panel

Instruction Manual

EHL

IMPORTANT INFORMATION

• Toughenedglassiscompletelysafeforuseinourshowerenclosuresandbathscreens;providingourproductsareinstalledaccordingtoour

guidelines.

• Itisimportanttonotethattheglassmustnotbemountedor‘pinched’insuchawaythatwouldcauseastresspointtodevelopintheglass.In

addition,itmustnotbesubjecttoanysharpimpactorseveretemperatureuctuationwhichmayalsocauseastresspointtodevelopintheglass.

• Toughenedglassisphysicallyandthermallysignicantlystrongerthanstandardglass.Duringthetougheningprocessthestressescontained

withinanyglassarebalancedsoifintheunlikelyeventsituationanyoftheaboveoccursandtheglassbreaks,theglasswillshattersafelyinto

smallthumbnailsizedbluntfragments.

Component Check List: Supplied

Description Quantity

EndCap 1

InlinePanel 1

LowLevelBracingAssembly 1

ScrewCoverTrim 1

Fixing Kit Components

Description Quantity

No4x1/4”PanHeadScrews 3

2.5mmDrillBit 1

BrandingBadge(ifapplicable) 1

5mmAllenKey 1

Equipment Check List: Not Supplied

Description

Electric/Batterydrill

6mmMasonryDrill

SpiritLevel

Screwdriver

PipeCutters

Hacksaw

Pliers

SealantGun

BathroomSealant

TapeMeasure

Pencil

Pleasemakesurethepurchaser/enduser

completesandreturnstheguaranteecard

whichisenclosedwiththisproduct.Failure

tovalidatetheGuaranteewillmeanonlythe1

YearStatutoryGuaranteewillapply.

CONSUMER GUARANTEE

PRE-INSTALLATION CHECKS

1. Checkyouhavethecorrectproduct.Pleaselookatthelabelsonthesideoftheproductpackaging.

2. Checkalltheproductcomponentsareintheboxandthexingkits.

3. Unpackyourproductandhandleitwithcare.

4. Pleasechecktheproductfordefectsordamage,oncetheinstallationhascommencedwecannotacceptresponsibilityforanydefectsordamage.

5. Pleasetaketimetoreadtheseinstructionspriortoinstallingyourproduct.

6. Beforeyoucommenceanydrillingchecktherearenohiddenelectricalcablesand/orwaterpipes.

7. Noattemptshouldbemadetore-workthetoughenedsafetyglass.

8. Theinstallationoftheproductshouldbeperformedbytwopersons.

9. Itisstronglyrecommendedthatthewallstheproductisgoingtobeinstalledonarevertical.

10. Itisstronglyrecommendedtheproductisttedonatiledsurfaceorsimilarwaterproofsurface.

11. Itisstronglyrecommendedthewallsaretiledandgroutedbeforetheproductisinstalled.

12. Ifthewallsand/orthetrayarenotlevelyouwillnotachievemaximumadjustmentoftheproduct.

13. Picturesusedareforillustrationpurposesonly,productdesignsmayalterslightlyasaresultofcontinuingproductdevelopment.

14. WedonotstipulatewheretheEuropeanStandardKiteMarkshouldbepositionedontheglasswhenbeingfactoryassembled.

15. Pleasenotethatsomenaturalmistingmayoccurwhenyouremovethisproductfromitspackaging,duetotheadditionoftheglassprotectionpre-

coating.Ifthisdoesoccurthiscaneasilyberemovedwithasoft,drycloth.

Ref:EHL-July2012

Step 1 - Inserting Door and Panel

1. LiftthedoorontothetrayandlocateintotheWallProle.

2. ApplyabeadofsealantthewidthoftheWallProlewherethe2ndprolewillmeetthetiledwallandtray.

3. Locatethe2ndWallProleontotheendoftheInlinePanel.

4. LifttheInlinePanelontothetrayandlocatefullyintotheverticalaluminiumofthedoor.

5. Screwxthe2ndWallProletothewall(makesuretheproleiscompletelyverticalusingaspiritlevel).

6. LifttheInlinePaneluptobeabletoaddabeadofsealanttotheinsideoftheWallProle

• You will need the assistance of someone when doing this procedure.

• Failure to carry out Stages 2 and 6 can result in serious water damage and will not be covered under the

terms of the guarantee.

IMPORTANT:Makesuresteps1to4oftheDoorInstallationGuidearecompletedbeforettingyourInline

Panel(Thedoorimageusedintheseinstructionsisanexampleonly).BesuretoremovetheblackTransit

Capsbeforeproceeding.

↓

①

②

③

④ ⑤

⑥

↓

③

↓

④

⑥

↓

②

Step 2 - Fixing Panel and Door

1. MakesuretheDoorandInlinePanelprolesarelocatedcorrectlyandarelevelatthetopandbottom.

2. Drillthroughthepre-drilledholeswiththe2.5mmdrillbit(supplied).

3. ScrewttheDoorandInlinePaneltogetherusingtheNo4x1/4”screws.

②

③ ③

Step3-FixingPanelandDoortoWallProles

1. CentretheDoorandInlinepanelbetweentheWallProles.

• NOTE:Aminimumof10mmisrequiredbetweentheInlinePanel/DoorandWallProlesforxing.

2. MakesuretheInlinePanelandDoorarecompletelyverticalusingaspiritlevel.

• Prior to drilling/screwing the Inline Panel and Door refer to the Door installation guide to understand the

 Doorttingandadjustmentrequirements.

3. DrillthroughtheWallProleintothePanelverticalwiththe2.5mmdrillbit(supplied),makesurethatthe

InlinePanelandDoorremaincompletelyverticalduringthisprocedure.

• You will need the assistance of someone when doing this procedure.

4. FitthebasesonthescrewsandfastentheWallProleandInlinePaneltogether,pushttheCoverCaps.

• ItmaybebenecialtoapplysomepressuretotheDoorandInlinePanelassemblyandcheckthedoor

 operationpriortoxingthedoorside.

③

①

Equal Equal

10mm

minimum

④CoverCap

Screw

Base

⑥

Step 4 - Bracing

1. MeasurethedistancefromthebackwalltotheoutsidefaceoftheInlinePanelGlass.

2. Deductthatmeasurementfrom1038mm,shortentheBraceBarbythenewamount(see*Exampleabove)

3. PlacetheserratedendofthestraightsectionintotheLowLevelbraceassemblyandfastentogetherby

tighteningtheSetScrew,slidetheWallCupontheoppositeendtocompletetheBraceBarassembly.

4. PositionthefullbracingassemblyontotheInlinePanelGlass,donotxatthisstage.LoosentheAllen

screwintheLowLevelbraceassemblysothatitcanbeturnedtoachievethecorrectangle.

• There should be no metal parts touching the glass, the spacers must be used.

5. SlidethewholeassemblyuptothetiledwalltodeterminethepositionoftheWallCup,markusingapencil.

6. UnscrewtheinsertfromtheWallCupandpositionitcentrallyonthepencilmark.Markthroughtheslotfor

thepositionofthescrewholethatistobedrilled.

7. Drilltheholeusinga6mmMasonryDrill(notsupplied)andttheWallPlug.

8. Fixtheinserttothewallusinga40mmscrew(supplied).ScrewtheWallCupontotheinsertuptothewall.

9. PlacetherestoftheBraceBarassemblyontothepanelandintotheWallCup,checkthateverythingis

placedcorrectly(includingspacersbeingtted)thentightenallthescrewswiththeAllenKeys(supplied).

• Thereis35mmofadjustmentintheBraceBarassemblytoallowforcorrectadjustment.

• The Brace Bar must be level, use a Spirit Level and ensure the bubble is in the middle of the two lines.

• Thepanelmustbeverticallylevel,useaSpiritLevelandadjustthebracingtoachievethis.

③

⑧ ⑦

LowLevelBrace

WallCup

SerratedEnd

Straight

Section

Set

Screw

⑤

NOTE:TheStraightSectionoftheBraceBarassemblymayneedshortening,ifsouseahacksaworsimilar.

ItisIMPORTANTthatitisshortenedattheWallCupend-besuretoremoveallburrsandsharpedges.

BraceBar(*Exampleonly)

GivenDimension 1038mm

Walltooutsideofglass *878mm

ReduceBraceBarby *160mm

②

Step 5 - Fitting Screw Cover, Caps and Sealing

1. FittheScrewCoverTrim(ifyouhaveroomthiscanbesliddownfromthetop).

• CuttheCovertrimsushwiththetopoftheverticalprolesusingaStanleyknifeorsimilar,pleasetake

care when cutting.

2. FittheTopCapstothetopoftheDoor/Panel.

• On the vertical between the Panel and Door it may be necessary to remove a front leg on the Panel side.

3. UsingagoodqualitysealantsealbothsidesoftheWallProlesverticallyinsideandoutsidewherethey

meetthetiledwalls.

4. Sealtheenclosurehorizontallythefulllengthtothetray/wetroomoorontheoutsideonly.

• IMPORTANT: Failure to follow Stages 3 and 4 may result in serious water damage and will not be covered

under the terms of the guarantee.

• Do not seal the inside of the enclosure horizontally.

• Please allow 24 hours for the sealant to fully cure before using the enclosure.

5. PlacetheBrandingBadge(ifapplicable)onaprominentnonemovingpartofaluminium..

②

↓

①

③

Spare Parts

Part No. Description Q’ty Part No. Description Q’ty Part No. Description Q’ty

1EndCap 111 21

2WallCupAssembly 112 22

325mmBraceBar 113 23

4ExpandableJoint 114 24

5LowLevelBracing 115 25

6InlinePanel 116

7ScrewCoverTrim 117

8 18

9 19

10 20

If you need to replace any damaged parts please see illustration below for parts list then

call Customer Relations on 01325 328033/328034

TROUBLE SHOOTING GUIDE

Problem Solution

Leaking 1. Checkthetrayhasbeensealedcorrectlypriortoinstallationoftheenclosure(Step1in

theDoorInstructions).

2. Checktheinsidegaphasbeensealedcorrectlybetweenthetrayandwallproles(Step

2intheDoorInstructionsandStep1intheseInstructions).

3. Checkthatthebaseoftheenclosureissealedtothetrayontheoutsideonly(Step5).

4. Checktoseeifbothwallproleshavebeensealedverticallyinsideandoutsidewhere

theymeetthetiledwall(Step5).

5. Checkthatthebaseoftheenclosurehasn’tbeensealedtothetopofthetrayonthe

insideofthecubicle.(Step5).

Important: This enclosure should be water tested conforming to BS EN 14428

Enclosure Alignment 1. Checkthattheenclosureisttedontoatiledwallorasimilarsealedsurface(Step1in

theDoorInstructions).

2. Checkthatthewallproleshavebeentted15mmfromthefrontoutsideedgeofthe

tray(Step2intheDoorInstructions).

3. Checkthatthewallproleshavebeenttedcompletelyvertical(thebubblemustbein

thecentreofthetwolinesonaspiritlevel-Step2intheDoorInstructions).

4. Checktheenclosureiscompletelyverticalandlevel(Step1intheDoorInstructions).

Door not Operating

Smoothly

1. Checkthatthetrayiscompletelylevel(thebubblemustbeinthecentreofthetwolines

onaspiritlevel).

2. Checkthatthewallproleshavebeenttedcompletelyvertical(thebubblemustbein

thecentreofthetwolinesonaspiritlevel).

Some important information to help you Maintain your product.

Thefollowinginformationisallyouneedtokeepyourproductlookingnew.

Cleanyourproductusingamilddetergentdilutedinwaterandthenpolishedoffusingasoftcloth.

Ifyouliveinahardwaterarea,periodicallycleanyourproductusinga50/50solutionofwhitevinegarandwater.The

solutionshouldbeleftontheenclosureforapproximately5minutesthenrinsedoffusingwarmwater.Thismethodof

cleaningshouldremovelimescaleresidue.

Simple Maintenance

Ourproductsaregenerallymaintenancefree,howeveritmaybenecessarytolubricatewheelassembliesandother

movingpartsfromtimetotime.

Itisstronglyrecommendedthataqualitysiliconesprayisused.

A list of Don’t’s:

1. Don’tuseacidicbasedproductswhichareunsuitableforcleaningenamelsurfaces.

2. Don’tuseabrasivecleanersorcleanersusingbleachorsolvents,theseproductswilladverselyaffectthenishof

thealuminiumproles.

3. Don’tusescouringpads,powderoranysharpinstrumentswhencleaningtheenclosure.

Shouldyouexperienceanyproblemsduringinstallationpleaserefertothe

TroubleShootingGuideorcontactCustomerRelationson:

+44 (0) 1325 328033/328034

Toenablecustomerrelationstoprovideyouwithanexcellentlevelofserviceitisimportantthatyou

quoteyourproductCodeandReferenceNumber-thesecanbefoundontheGuaranteecard.

Table des matières

Autres manuels ERGONOMIC Appareil de salle de bains

ERGONOMIC

ERGONOMIC OBV3 Manuel utilisateur

Manuels Appareil de salle de bains populaires d'autres marques

DURAVIT

DURAVIT C.1 C15240 0090 Manuel

Heatstore

Heatstore HSTRL500WTN Manuel utilisateur

Sunshower

Sunshower PURE SOLO Manuel utilisateur

Delabie

Delabie Delabie Sporting 714700 Manuel utilisateur

Kohler

Kohler K-13056 Instructions de montage

ESS

ESS Container TCL-11 Manuel utilisateur

Mustee

Mustee 22C Manuel utilisateur

VITRA

VITRA V-Flow Manuel utilisateur

baliv

baliv DUK-80.30 T Manuel utilisateur

Malmet

Malmet B105BT Manuel utilisateur

bathstore

bathstore Transition H1690MM Mode d’emploi

BELLOSTA

BELLOSTA Edward 0800/M Manuel utilisateur

baliv

baliv DU-5160 Manuel utilisateur

Franke

Franke PRTR0006 Manuel utilisateur

Gessi

Gessi RILIEVO 59011 Manuel utilisateur

noken

noken VITAE 100188525-N299998810 Manuel utilisateur

Allen + Roth

Allen + Roth 1142VA-30-201 Manuel utilisateur

Britex

Britex HBDA Manuel utilisateur