ERGOMART TRS413 Manuel utilisateur

To separate the tilter head from the tilter head yoke,

grasp the tilter head in one hand and yoke in the other.

Work the tilter head free by moving it slightly left and

right as you pull upward.

Insert the TRS413 pole into the opening on the top of

the Mount Kit.

TRS413 - BB103 MONITOR & KEYBOARD STAND

Installation Instructions

Ergonomic solutions for office and light industrial work environments

www.ergomart.com | 888 420 3200

1 2

3 4

5 6

Insert the Carriage Bolt into the square center-hole in

the VESA Slider plate so that the screw head rests

underneath the raised middle section. Place the LCD

monitor face down on a flat surface (use a towel or cloth

to protect the monitor from scratches) and align your

VESA Slider Adapter (with the raised middle section up).

Align holes with the corresponding holes on the back of

the monitor. Secure each Part D screw with the Phillips

Head Screwdriver by turning clockwise until each is tightly

secured.

Align the Tilter Head rotation plate with the 4 holes on the

backside of the BB103 Back Bar at the position which you

prefer. Secure each screw (Part A) with the Phillips

Head Screwdriver by turning clockwise until each is

tightly secured.

Secure pole by inserting the Allen key (Tool B) into 3/32”

set screw on the side of the mount cup and then turn

clockwise (to the right) until the pole is snug.

Loosen Ring Collar on pole to reposition tilter head

assembly to the anticipated optimal position and then

rotate the thumb screw clockwise until the Ring Collar

is secure.

Assembly of the TRS413 is now completed.

To contain wires, push the open end of the wire management

clip over the pole with the wires resting in the middle.

Ergonomic solutions for office and light industrial work environments

7 8

910

11 12

Carefully position the BB103 and tilter head assembly

so that the silver pin is aligned with the opening of the

Tilter Head Yoke. Insert by pushing down. It may be

necessary to rotate the entire assembly slightly left and

right to ease the pin into position.

Place one of the Plastic Slider Plate Washers onto the

Carriage Bolt protruding from the back of the monitor with

attached VESA Slider Plate. Lift the monitor and place the

Carriage Bolt end through the vertical slot on the BB103

Back Bar. Place the second Plastic Slider Plate Washer

over the end of the Carriage Bolt on the back side of the

BB103. Secure Monitor to the BB103 by placing the Plastic

Knob on the end of the Carriage Bolt and rotating clock-

wise.

Align the registration pins of the Part C dog washer with

the small opening on the bottom of the Tilter Head pin.

Insert the Part B screw into the center hole of Part C.

During final adjustments, this screw can be tightened or

loosened to increase or decrease the resistance to

rotation.

To adjust the tilt of the LCD Monitor, you will need to

insert Allen key (Tool A) into the set screw at the base

of the Tilter Head. Loosen by twisting clockwise and

tighten by turning counterclockwise.

TRS413 - BB103 MONITOR & KEYBOARD STAND

Installation Instructions

www.ergomart.com | 888 420 3200

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ERGOMART Support et étagère

ERGOMART

ERGOMART TRS2818 Manuel utilisateur

ERGOMART

ERGOMART PM90 Manuel utilisateur

ERGOMART

ERGOMART SAA2045 Manuel utilisateur

ERGOMART

ERGOMART POS18-3005 Manuel utilisateur

ERGOMART

ERGOMART SAA179 Manuel utilisateur

ERGOMART

ERGOMART WS9110 Manuel utilisateur

ERGOMART

ERGOMART LS1512 Manuel utilisateur

ERGOMART

ERGOMART LEVERLIFT Manuel utilisateur

ERGOMART

ERGOMART EQP3418 Manuel utilisateur

ERGOMART

ERGOMART TRS2718-BB103 Manuel utilisateur

ERGOMART

ERGOMART SAA7000 Manuel utilisateur

ERGOMART

ERGOMART DS9109 Series Manuel utilisateur

ERGOMART

ERGOMART Dorian Triple Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur