ErGear EGSS2 Manuel utilisateur
Model: EGSS2
Monitor Desk Mount
Instruction Manual V2.0
Thank you for choosing this Ergear product! At Ergear we strive to
provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to
Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it
is strictly prohibited to dismantle without professionals. Please return to the manufacturer
or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
01
Weight Restrictions
6.6-26.4 lbs.
(3-12 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only with
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
If your monitor weighs more, this mount is NOT
compatible.
Your monitor (including
accessories) CANNOT EXCEED
6.6-26.4lbs (3-12 kg)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
100 mm ≈ 4 in.
75 mm ≈ 3 in.
C-Clamp Mounting
Grommet Mounting
Product Features
02
Warning!
Do not adjust tension without monitor.
1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is between
6.6~26.4 Ibs (3-12 kg).
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
03
3
Parts and Hardware Included
1. Install the Base
1/8 in.
(3mm)
5/32 in.
(4mm)
13/64 in.
(5mm)
Warning:
Ensure bolts are
secured firmly.
01 X1 02 X1
05 X1
03 X1 04 X1
DE G
A. For Clamp Mounting A-1 Install the USB Cable and C Clamp to the
Base
M4x12mm
Bolt (x4)
A
M4x16mm
Bolt (x4)
B-1
Bolt (4pcs)
M6x12mm
C
M8x38mm
Bolt
φ16xφ8.2x1.5mm
Washer
Base
Arm ExtenderArm Decorative Cover C-Clamp
06 X1
Monitor Plate
Allen Key
F
Locking
Plate
H
Pressure
Plate
2Install the USB cable [07] to
the base [03], then secure part [Y]
to the base [03]
Connect part [X] to part [Y] according to the thickness of the desktop
Y
X
1Detach the C-clamp entirely
E
(4mm) X
Y
5mm
Spacer (x4)
B-2
07 X1
USB Cable
X
YX
Y
OR
E
(4mm)
C
Y
07
03
Grommet
Bolt
Butterfly
Nut
04
Warning:
Ensure bolts are
secured firmly.
B. For Grommet Mounting
Ensure bolts are
secured firmly
A-2 Secure the Base to the Desktop
B-1 Install USB Cable and the Grommet
Bolt to Base
B-2 Secure the Base to Desktop Using Locking Plate and Butterfly Nut
12
2
1 2
1
D
D
F
E
5/32in.
(4mm)
07
03
H
05
2. Install the Arms
3. Install the Monitor Plate
1 2
3 4
1/8 in.
(3mm)
1/8 in.
(3mm)
E
E
13/64 in.
(5mm)
E
G
06
01
01
02
03
Do not over-tighten the set
screw [M] in order not to
affect the rotation of the arm.
M
M
M
M
Attach the monitor plate [06] from the sides
of the top end of arm [01], then secure the
monitor plate using bolt and washer [G]
06
5. Adjust Gas Spring Tension
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Be sure to keep the arm in
horizontal position during
adjustment. Or else, it would
be difficult to adjust the
mount or damage the mount.
1. If the monitor can stay at the desired height
by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep
it in horizontal position and then use the 13/64
in.(5mm) Alley key (E) to turn the bolt
clockwise(“-” direction) to reduce tension of
the arm only until the monitor can stay at the
desired height by itself.
3. If the monitor falls down, lift the arm to keep
it in horizontal position and then use the 13/64
in.(5mm) Alley key (E) to turn the bolt
counter-clockwise(“+” direction) to increase
tension of the arm only until the monitor can
stay at the desired height by itself.
4-1 Choose Proper Bolts 4-2 Install Monitors to the Arms
10.1-0.2in.(3-5mm) spacing left
100x100mm
75x75mm
A
Screwdriver
[Not Included]
Flat back monitor
Curved back monitor
4. Attach Monitors to the Arms
07
100x100mm
75x75mm
B-1
B-2
The tension is preset at
8.8-11 LBS(4-5kg). After
hanging the monitor to
the mount, please release
the monitor slowly to
prevent it from falling
suddenly.
6. Rotation Restriction
Non-proper usage directions Proper usage directions
(1 rotation ≈ 1 lb)
13/64 in.
(5mm)
E
E
13/64 in.
(5mm)
08
Pinch the both sides of the top end of
the cover to make it attach to the arm
4. Route Cables along the Arm
7. Tilt Adjustment
8. Route Cables along the Arms
31 2
64
13/64 in.
(5mm）
E
Adjust monitor to proper tilt angle, using Allen key (E) to tighten the bolt and fix tilt angle
5
Pull down the groove part along the
arm to detach the cover from the arm
8-1 Route cables along the arm [01]
8-2 Route cables along the arm extender [02]
01
02
b
09
Table des matières
Autres manuels ErGear Support et étagère
ErGear
ErGear EGSS1 Manuel utilisateur
ErGear
ErGear EGDS7 Manuel utilisateur
ErGear
ErGear EGDS6 Manuel utilisateur
ErGear
ErGear EGDS9 Manuel utilisateur
ErGear
ErGear EGSS7 Manuel utilisateur
ErGear
ErGear EGSS3 Manuel utilisateur
ErGear
ErGear EGDS15B Manuel utilisateur
ErGear
ErGear EGCM5 Manuel utilisateur
ErGear
ErGear EGDS3 Manuel utilisateur
ErGear
ErGear EGCM7 Manuel utilisateur
ErGear
ErGear EGSS9 Manuel utilisateur
ErGear
ErGear EGCM12 Manuel utilisateur
ErGear
ErGear EGDS2 Manuel utilisateur
ErGear
ErGear EGCM1 Manuel utilisateur
ErGear
ErGear EGCM6 Manuel utilisateur
ErGear
ErGear EGCM12 Manuel utilisateur
ErGear
ErGear EGTS5B Manuel utilisateur
ErGear
ErGear EGESD1 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
