Equinox Systems Fusion 140 Manuel utilisateur

Fusion 140

User Manual

Order code: EQLED074

www.prolight.co.uk Fusion 140 User Manual 2

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 100~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: One year from date of purchase.

www.prolight.co.uk Fusion 140 User Manual 3

Product overview & technical specications

Housing 7 x 18W HEX colour LEDs, RGBWAUV the Fusion 140 moving head

wash gives smooth colour mixing from rich saturated hues to subtle pastel

shades. The compact and lightweight design allows for easy transportation

and installation. The 4 push button LED menu allows for easy access to the

functions including DMX, auto, sound active and master/slave modes. Fast

movements along with a host of on-board options makes this xture great

for either installations or mobile entertainers.

• 7 x 18W six-colour LEDs (RGBWAUV)

• Beam angle: 35°

• 2,930 Lux @ 2m (full on)

• DMX channels: 11 or 15 selectable

• Auto, sound active and master/slave

modes plus built-in programs

• Pan/tilt auto correction

• 16-Bit pan/tilt positioning

• Pan: 540°, Tilt: 180°

• 0-100% dimming and variable strobe

• Supplied with quick release

omega clamp

• 4 push button menu with

LCD display

• PowerCON input/output

• 3-Pin XLR input/output

• Fan cooled

Fusion 140

0m 1m 2m 3m 4m 5m

25°

25° - Lux

FULL ON

11720

1836

4032

644

3700

2148

N/A

2930

459

1008

161

925

537

N/A

1302

204

448

71.5

411

238

N/A

732

114

252

40.2

231

134

N/A

468

73.4

161

25.7

148

85.9

N/A

Specications Fusion 140

Power consumption 130W

Power supply 100~240V, 50/60Hz

Fuse F3.15A

Dimensions 310 x 262 x 155mm

Weight 4.5kg

Order codes EQLED074

96mm

155mm

310mm

168mm

262mm

www.prolight.co.uk Fusion 140 User Manual 4

Technical specications

04 06

03 05

02 01 10 11 12 09

01 - LCD display

02 - Function buttons

03 - DMX indicator

04 - Master indicator

05 - Slave indicator

06 - Sound indicator

07 - On/off switch

08 - 3-Pin DMX input

09 - 3-Pin DMX output

10 - PowerCON input

11 - PowerCON output

12 - Fuse F3.15A 250V

13 - Fan

In the box: 1 x xture,

1 x power cable,

1 x omega clamp,

& 1 x user manual

www.prolight.co.uk Fusion 140 User Manual 5

Operating instructions

DMX

Address DMX address setting

Address

001

Address

512

Show

Mode Show modes

Show 0

Show 7

Black

Out Blackout mode

Yes

Sound

State Sound mode

Off

Sound

Sense Sound sensitivity

100

Channel

Mode

02Chan

16Chan

DMX channel setting

10Chan

Slave

Mode

Master

Slave2

Master/slave mode

Slave1

Red

255

Blue

255

Green

255

White

Balance

Red

Blue

White

balance

setting

Green

www.prolight.co.uk Fusion 140 User Manual 6

Pan

Inverse Pan invert setting

Yes

Tilt

Inverse Tilt invert setting

Yes

Back

Light Backlight setting

Off

Auto

Test Auto test

Test...

Temp. Fixture temperature

___°C

Fixture

Time Fixture total run time

_____

Firmware

Version Fixture software version

v_._

Reset Factory reset

Fan

Speed

Auto Run

Fastest

Medium

Slow

Fan speed setting

OFF

www.prolight.co.uk Fusion 140 User Manual 7

Operating instructions

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the xture and each xture independently.

To access the DMX address mode, press the “MENU” button to show “DMX Address” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the required DMX address.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

DMX channel mode:

To access the DMX channel mode, press the “MENU” button to show “Channel Mode” on the LCD

display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose one of the 2,

10 or 16 DMX channel modes. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

PLEASE NOTE:When the unit is receiving DMX the red DMX indicator on the front panel will illuminate.

10 channel mode:

Channel Value Function

CH1 000-255 Pan adjustment 0-540°

CH2 000-255 Tilt adjustment 0-180°

CH3 000-255 Master dimmer (0-100%)

CH4 000-009 No function

010-255 Strobe (slow-fast)

CH5 000-255 Red (0-100%)

CH6 000-255 Green (0-100%)

CH7 000-255 Blue (0-100%)

CH8 000-255 White (0-100%)

CH9 000-255 Amber (0-100%)

CH10 000-255 UV (0-100%)

Channel Value Function

CH1

000-006 No function

007-037 Show 0

038-068 Show 1

069-099 Show 2

100-130 Show 3

131-161 Show 4

162-192 Show 5

193-223 Show 6

224-255 Show 7

CH2

000-009 No function

010-255 Sound active

(sensitivity low-high)

2 channel mode:

www.prolight.co.uk Fusion 140 User Manual 8

Operating instructions

16 channel mode:

Channel Value Function

CH1 000-255 Pan adjustment 0-540°

CH2 000-255 Pan ne adjustment

CH3 000-255 Tilt adjustment 0-180°

CH4 000-255 Tilt ne adjustment

CH5 000-255 Pan/tilt speed

CH6 000-255 Master dimmer (0-100%)

CH7 000-009 No function

010-255 Strobe (slow-fast)

CH8 000-255 Red (0-100%)

CH9 000-255 Green (0-100%)

CH10 000-255 Blue (0-100%)

CH11 000-255 White (0-100%)

CH12 000-255 Amber (0-100%)

CH13 000-255 UV (0-100%)

CH14

000-038 Blackout

039-044 Red

045-050 Green

051-056 Blue

057-062 White

063-068 Amber

069-074 UV

075-080 Yellow

081-086 Magenta

087-092 Pastel red

093-098 Orange

099-104 Hot pink

105-110 Cyan

111-116 Pastel green

117-122 Lime green

123-128 Mint green

129-134 Pastel blue

135-140 Violet

141-146 Blue

147-152 Pastel amber

153-158 White

159-164 Coral

165-170 White (RGB)

171-176 Pastel yellow

177-182 Medium yellow

Channel Value Function

CH14

cont.

183-188 Yellow Green

189-194 Lavender

195-200 Pink

201-206 Purple

207-212 Rose pink

213-218 Pastel pink

219-224 Vibrant pink

225-230 Sky blue

231-236 Light cyan

237-242 Medium blue

243-248 Pale green

249-255 Aqua

CH15

000-006 No function

007-037 Show 0

038-068 Show 1

069-099 Show 2

100-130 Show 3

131-161 Show 4

162-192 Show 5

193-223 Show 6

224-255 Show 7

CH16

000-009 No function

010-235 Sound active

(sensitivity low-high)

236-245 No function

246-255 Motor reset (hold 5s)

www.prolight.co.uk Fusion 140 User Manual 9

Show mode:

To access the show modes, press the “MENU” button to show “Show Mode” on the LCD display. Now

press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between

“Show 0” ~ “Show 7” (Show 7 – forward facing show). Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Master/slave mode:

To set the master unit, press the “MENU” button to show “Slave Mode” on the LCD display. Now press

the “ENTER” button and use the “UP” and “DOWN” buttons to choose “Master”. Press the “ENTER” but-

ton to conrm the setting. Then select your desired program.

To set the other units in slave mode, press the “MENU” button to show “Slave Mode” on the LCD dis-

play. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose either “Slave1” or

“Slave2”. Press the “ENTER” button to conrm the setting.

The unit will now run in sequence with the master unit.

To exit out of any of the above options, press the “MENU” button.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Blackout setting:

To access the blackout setting, press the “MENU” button to show “Black Out” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between “No” or “Yes”.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

PLEASE NOTE:The xture must be set to “NO” for Show modes to run.

Sound/sound sensitivity:

To turn the sound mode on or off, press the “MENU” button to show “Sound State” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between “On” or “Off”.

Press the “ENTER” button to conrm the setting.

To adjust the sound sensitivity, press the “MENU” button to show “Sound Sense” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between 0 ~ 100.

Value: 0 - 100 (0 = low, 100 = high)

To exit out of any of the above options, press the “MENU” button.

White balance setting:

To access the white balance setting, press the “MENU” button to show “White Balance” on the LCD

display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between

“Red”, “Green” or “Blue”. Press the “ENTER” button and use the “UP” and “DOWN” buttons to adjust the

white balance between 50 ~ 255. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Operating instructions

www.prolight.co.uk Fusion 140 User Manual 10

Operating instructions

Pan invert setting:

To access the pan invert setting, press the “MENU” button to show “Pan Inverse” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between “No” or “Yes”.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Tilt invert setting:

To access the tilt invert setting, press the “MENU” button to show “Pan Inverse” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between “No” or “Yes”.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Backlight setting:

To access the display backlight setting, press the “MENU” button to show “Back Light” on the LCD

display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to choose between “Off”

or “On”. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Auto test:

To access the xtures auto test mode, press the “MENU” button to show “Auto Test” on the LCD display.

Now press the “ENTER” button, the xture will now run through its auto test.

To exit out of any of the above options, press the “MENU” button.

Fixtures temperature:

To access the xtures temperature, press the “MENU” button to show “Temp.” on the LCD display.

Press the “ENTER” button, the LCD display will now show the xtures temperature.

To exit out of any of the above options, press the “MENU” button.

Fan speed:

To access the fan speed setting, press the “MENU” button to show “Fan Speed” on the LCD display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Auto Run”,

“OFF”, “Fastest”, “Medium” or “Slow”. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Fixture time:

To access the xtures total run time, press the “MENU” button to show “Fixture Time” on the LCD

display. Press the “ENTER” button, the LCD display will now show the xtures total run time.

To exit out of any of the above options, press the “MENU” button.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Equinox Systems Matériel de DJ

Equinox Systems

Equinox Systems Helix 100W Gobo Flower Manuel utilisateur

Equinox Systems

Equinox Systems C-Shot Manuel utilisateur

Equinox Systems

Equinox Systems EQLED003 Manuel utilisateur

Equinox Systems

Equinox Systems EQLED054 Manuel utilisateur

Equinox Systems

Equinox Systems Stratos Duo RGB Manuel utilisateur

Equinox Systems

Equinox Systems Blitzer Strobe Manuel utilisateur

Equinox Systems

Equinox Systems Beamtastic Manuel utilisateur

Equinox Systems

Equinox Systems Spark Stream Manuel utilisateur

Equinox Systems

Equinox Systems Helix Scan XP 150W Scanner Manuel utilisateur

Equinox Systems

Equinox Systems Butterfly Quad Manuel utilisateur

Equinox Systems

Equinox Systems Twin Shot MKII Electric Confetti Launcher Manuel utilisateur

Equinox Systems

Equinox Systems Ultra LED Scan EQLED75 Manuel utilisateur

Equinox Systems

Equinox Systems Triton Beam EQLED071 Manuel utilisateur

Equinox Systems

Equinox Systems Viper Manuel utilisateur

Equinox Systems

Equinox Systems Cabaret Colour HEX Manuel utilisateur

Equinox Systems

Equinox Systems EQLED064 Manuel utilisateur

Equinox Systems

Equinox Systems EQLED368 Manuel utilisateur

Equinox Systems

Equinox Systems FXbar18 Manuel utilisateur

Equinox Systems

Equinox Systems Fusion 200 Zoom Spot Manuel utilisateur

Equinox Systems

Equinox Systems Power Par 54 MKIII Manuel utilisateur

Equinox Systems

Equinox Systems Stratos Wash RGBA Manuel utilisateur

Equinox Systems

Equinox Systems SpectraPix Batten Manuel utilisateur

Equinox Systems

Equinox Systems Six Shooter MKII Manuel utilisateur

Equinox Systems

Equinox Systems MaxiPar Quad Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur