Epson ActionScanner ActionScanner II Manuel utilisateur
EPSON
ACTIONSCANNER™II
Getting Started
for Macintosh
@
printed on recycled paper with at least 10% post-consumer content
A Note Concerning Responsible Use of
Copyrighted Materials
Like photocopiers, scanners can be misused by improper copying of copyrighted material.
Although Section 107 of the U.S. Copyright Act of 1976 (Title 17, United States Code), the
“fair use” doctrine, permits limited copying in certain circumstances, those circumstances
may not be as broad as some people assume. Unless you have the advice of a
knowledgeable attorney, be responsible and respectful by not scanning published material
without the permission of the copyright holder.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying.
recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
No patent liability is assumed with respect to the use of the information contained herein.
Neither is any liability assumed for damages resulting from the use of the information
contained
herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by purchaser or
third parties as a result of: accident, misuse, or abuse of this product or unauthorized
modifications, repairs, or alterations to this product.
Seiko Epson Corporation and its affiliates shall not be liable against any damages or
problems arising from the use of any options or any consumable products other than those
designated as Original EPSON Products or EPSON Approved products by Seiko Epson
Corporation.
ActionScanning is a trademark of Epson America, Inc.
EPSON is a registered trademark of Seiko Epson Corporation.
General notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective companies. EPSON disclaims any and all rights in those mark.
Copyright
0
1995 by Epson America, Inc.
Torrance, California, USA
12/95
Contents
Introduction ...........................
1
System and Memory Requirements
.............
2
Setting Up the Scanner
.....................
2
Connecting the Scanner to Your Macintosh
.........
4
Installing the EPSON Scanning Utilities
...........
6
Installing Adobe PhotoDeluxe
................
8
Installing Maxsoft-Ocron Wordlinx .............
9
Scanning Images
........................
9
Putting It Together
.......................
11
Calibrating Your System
..................
12
Selecting the Correct Resolution
.............
18
iii
Introduction
This package contains everything you need for professional
quality color scanning:
Q
EPSON® ActionScanner™ II color scanner, which scans in
full color (24 bit) or grayscale monochrome (8 bit) at
300 dpi (dots per inch)
Q
SCSI system cable
CI
EPSON Scanning Utilities for Macintosh® (EPSON Scan! II
and EPSON TWAIN), which let you capture scanned
images, export the images in a variety of formats, calibrate
your scanner, and use the scanner’s advanced features with
software programs that support the industry standard
TWAIN interface
P
Adobe® PhotoDeluxe,® a powerful, imageediting program
(supplied on a CD) that lets you edit color digital images
captured with your scanner or a digital camera, or copied
to a PhotoCD.
Cl
Maxsoft-Ocron™ Wordlinx,™ an optical character
recognition (OCR) program that lets you scan printed text
and convert it into a text file you can edit and format.
This booklet tells you how to set up your scanner, install the
software, and scan an image. If you need more detailed
information after you begin scanning, consult the manuals and
online documentation for the ActionScanner II, EPSON
Scanning Utilities for Macintosh, PhotoDeluxe, and Wordlinx.
1
System and Memory Requirements
For the scanner and your software to work properly, your
system must include the following minimum configuration:
D
Apple® Macintosh or Power Macintosh™ computer with a
68030 or 68040 processor
P
Apple system software 7.0 or higher
Q
8MB of system RAM; 4MB of application RAM
Note:
8MB is the minimum amount of RAM; graphics applications run
faster and more efficiently with at least 12MB of RAM.
0
At least 100MB of free hard disk space for scanner
applications and images, depending on the size of the
images
0
A color monitor (one with a 24-bit video card is
recommended)
4
For PhotoDeluxe, a double-speed or faster CD-ROM drive.
Setting Up the Scanner
Follow these steps to set up the scanner:
1.
Take the scanner out of its box and place it on a flat, stable
surface with the rear panel facing you.
2.
Remove the tape securing the scanner cover and pull out
the paper underneath the cover.
2
3.
Locate the round screw in the middle of the rear panel and
turn it counterclockwise. If necessary, use a coin to loosen it.
4.
Remove the screw and push it into the storage hole marked
STOCK;
do not screw it in.
5.
Connect one end of the power cable to the power inlet on
the rear of the scanner and plug the other end into an
appropriately grounded electrical outlet as shown below.
If the scanner comes on when you plug it in, turn it off by
pressing the
OPERATE
button.
Warning:
Whenever you
turn
off the scanner, wait at least 10 seconds
before turning it back on. Rapidly turning it on and off can
damage the scanner.
Connecting the Scanner to Your
Macintosh
Follow the steps below to connect
the
scanner directly to the
SCSI port on your Macintosh using
the
SCSI cable included
with the scanner. This cable has a 25-pin connector on one end
and a 50-pin connector on the other. The SCSI ID is already set
to 2 and the SCSI terminator is on.
If you are already using the SCSI port on your computer for
another SCSI device, such as an external hard disk, you need a
SCSI cable with a 50-pin connector
on
both ends. You can then
connect the scanner to your other SCSI device and set the SCSI
ID and terminator as necessary; follow the instructions in
Chapter 1 of your scanner User’s Guide.
1.
2.
3.
4.
5.
Turn off your Macintosh, scanner, and all peripheral devices.
Caution:
Be sure that your Macintosh, scanner, and all peripheral devices
are turned off before you plug in the SCSI cable.
Plug the 25-pin connector into the SCSI port on the Macintosh
with a
e
icon above it. Tighten the two screws on the
sides of the connector.
Connect the 50-pin end of the cable to either the top or
bottom SCSI connector on the scanner; then fasten the
connector with the wire clamps on its side.
Turn on the scanner by pressing the
OPERATE
button. The
green OPERATE
light comes on on the top right side of the
scanner. The
READY
light comes on when the scanner has
warmed up.
Then turn on your Macintosh. (Always turn on the scanner
before turning on the Macintosh.)
Installing the EPSON Scanning Utilities
The EPSON Scanning Utilities include EPSON Scan! II and
EPSON TWAIN for the Macintosh. Scan! II uses TWAIN to
capture images and then saves and exports these images in a
variety of file formats. It also calibrates your scanner and
output devices to produce images nearly identical to the
originals.
EPSON TWAIN is a set of drivers designed to access your
scanner’s advanced features for any software that supports
TWAIN for Macintosh. TWAIN drivers are an industry
standard for acquiring image data from a variety of external
sources without leaving your application program.
Follow these steps to install the EPSON Scanning Utilities:
1.
2.
3.
4.
5.
6.
Turn on the scanner.
Hold down the
Shift
key while turning on the Macintosh to
turn off any extensions.
Insert the EPSON Scanning Utilities Disk 1 in a diskette drive.
Double-click the
Disk
1 icon on the desktop.
Double-click the
Installer
icon in the Disk 1 folder.
After a few moments, you see the initial setup screen.
Choose
OK
to continue.
6
You see the Easy Install screen:
7.
8.
9.
Easy install
Click Install to place the
It
l Scanner Utility Program EPSON Scan! II
on the hard disk named
63
ZFP 320
I
Customize
1
If you want to install all the program components, click
Install.
To select only one or two components, click
Customize.
Then highlight the components on the next
screen and click
install.
The program begins copying files. Insert the diskettes as
prompted.
When installation is complete, you see a success message.
Click
Restart
to restart your Macintosh.
The program creates an EPSON Scan! II folder on your hard
disk containing a Scan! II and Scan! II Help icon.
10. Raise the scanner’s cover and place an image face down on
the upper right comer of the glass surface. Then carefully
close the cover.
11. To test your software, click the
Scan! II
icon.
12. From the File menu, select
Acquire.
7
Autres manuels pour ActionScanner ActionScanner II
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Epson Scanner
Epson
Epson Expression 1600 Manuel utilisateur
Epson
Epson ES-200 Mode d’emploi
Epson
Epson 1250 - Perfection Photo Flatbed Scanner Manuel utilisateur
Epson
Epson CaptureOne TM-S1000 Manuel utilisateur
Epson
Epson Fluid Mount Accessory Fiche technique
Epson
Epson GT-10000+ Manuel utilisateur
Epson
Epson 2400 - Perfection Photo - Dpi x Manuel utilisateur
Epson
Epson 1250 - Perfection Photo Flatbed Scanner Manuel utilisateur
Epson
Epson Perfection 640U Series Guide d'installation
Epson
Epson V500 Manuel utilisateur
Epson
Epson ES-580W Manuel utilisateur
Epson
Epson ES-865 Manuel utilisateur
Epson
Epson Perfection V700 Series Dimensions
Epson
Epson CaptureOne 30DPM Manuel utilisateur
Epson
Epson 3170 - Perfection Photo Mode d’emploi
Epson
Epson Perfection 636 Manuel utilisateur
Epson
Epson GT-20000 Manuel utilisateur
Epson
Epson Perfection 636U Manuel utilisateur
Epson
Epson Perfection 636 Guide de démarrage rapide
Epson
Epson Macintosh Manuel utilisateur
