Epson Stylus C120 Series Manuel d'utilisation et d'entretien

Instructional Manual Continuous Ink System for use in Epson Photo C120 printer

Before using this product, please read and follow the instructions. After opening your package, make sure to check that all the

accessories shown in figures 1-1 through 1-3 below are included.

Conduct Parts Check:

1. Accessories

a. Continuous Ink System (1) b. Air breather plugs (6), Syringe (1) & Screwdriver (1)

c. T shape Adhesive Pad (1) & square adhesive pad (1)

Fig. 1-1 Fig. 1-2 Fig.1-3

2. Set-Up Continuous Ink System (CIS)

a. Before installation, lay out all your parts in front of your printer.

b. Check your system for any leakage and make sure your tubing system is tightly connected and straight.

c. Place the CIS on the right hand side of the printer as shown on Fig.2-1 and keep it at the same level as the printer.

d. Hold down the ink tank with one hand and unplug the original air stoppers as shown on Fig.2-2, make sure to save

these for future use.

e. Install the Air Breather wider end into the ink reservoir tank, making a snug fit. (Fig.2-3)

Caution: Make sure not to push the breathers too tight as it could crack the tank. Also when removing the air breathers

from the tank use caution to avoid cracking.

Fig.2-1 Fig.2-2 Fig.2-3

3. Cartridge Installation

a. Unplug the printer power.

b. Use the screwdriver to remove the cartridge carrier cover as shown in Fig 3-1 & 3-2.

c. Take out the original cartridges.

d. Install the CIS cartridges into the cartridge carrier in their corresponding color position. (Fig 3-3)

Fig.3-1 Fig.3-2 Fig.3-3

4. Tube Adjustment and Positioning

a. Place the T shape adhesive pad as shown in Fig 4-1.

b. Place the square adhesive pad on the outside of the printer. (Fig.4-2)

c. Adjust tubing between cartridge compartment and tube guide to correct length; allowing enough room for the cartridge

to move back and forth freely (Fig.4-2 & 4-3). Make sure the tubes are not twisted and are straight (Fig.4-3).

Fig.4-1 Fig.4-2 Fig.4-3

d. Turn on the printer and make sure the system moves smoothly.

5. Refilling Ink

When the ink levels reach the indicator margin, (sticker on the ink tank with red line) the ink tank system

has reached its low level line and needs to be refilled.

Follow these steps:

1. Gently remove the air breather plugs in order to have more filling room.

2. Remove the plugs off of the refilling hole and refill the proper color of ink into the corresponding tank. (Fig 5-2)

Use towel to wipe off any spillage.

3. Make sure you use the specially designed ink Low Foam Ink for the CI System as they are specifically designed for

optimal results.

NOTE: When removing the CIS, remove cartridges and put tape or a napkin over ink exit hole.

Printer and ink tank MUST remain at the same level (not higher and not lower).

Fig 5-1 Fig 5-2

6. Attention:

1. After installing the CI System, do not remove the cartridges unless it is necessary. If cartridges are removed,

immediately place cartridges upside down with ink exit holes facing up to avoid leaking. If cartridges are

removed for more than an hour, please cover ink exit holes with tape.

2. When you are printing do not move the ink tank up or down. Keep it stable and at the same level as the printer.

3. Store at 15-35 degrees Celsius.

4. The ink and cartridge flow have been designed and tested to function as a system. We recommend you use the

specially designed ink Low Foam Ink in the CIS for optimal results.

7. Caution:

1. Do not ingest ink and keep out of reach of children.

2. Do not leave under sunlight or in extreme weather conditions.

3. Do not drop ink tank or handle roughly.

Thank you for purchasing the Continuous Ink System: We hope you found this manual useful.

Troubleshooting tips

Problem Suggestion

If the ink tank is full of ink, computer shows a message

“Replace Cartridge”. The printer keeps track of how

much ink is being used and thinks that the cartridge

should be empty, so you will have to reset the cartridges

chips.

1. Turn off printer and turn it back on.

2. Take out the cartridges, then reinstall, and continue printing

normally.

Banding or white lines in my print outs.

There is air in the system or cartridges. Try running a couple of

cleaning cycles. If white lines continue, use the provided

syringe to suck the air out of the bottom of the trouble cartridge

and you can add the ink that fills the syringe back into the top of

the CI system. (Make sure to thoroughly rinse the syringe

thoroughly after completing each color)

When I have completed a printing job, the ink is

siphoning backwards down the tubing.

The shipping plugs need to be removed before installing and

replaced with the air breathers to eliminate any pressure being

built up in the system, along with protecting the ink from

contamination. Also the ink tank should be sitting on the same

level surface as the printer. If the air breathers are covered with

dried ink, you can rinse the air breather and dry thoroughly to

regain use.

The tubing is getting caught inside the printer resulting in

an error message“paper loading error”.

Please adjust the tubing, it is not adjusted correctly. Give just

enough room for tubing to move to the left and back to the right.

After refilling the tanks the printer won’t print.

If the ink is added into the system too quickly, then it allows air

to enter the system. Use the provided syringe to extract ink and

air from the bottom of the cartridges. The ink that fills the

syringe can be slowly added back into the top of the ink tank.

After installing the CI system, the printer does not

recognize some of the cartridges.

Remove the cartridges, turn off the printer and reinstall the

cartridges. Then you can continue printing.

If you are still unable to fix the problem call your dealer for support.

Autres manuels pour Stylus C120 Series

Table des matières

Autres manuels Epson Imprimante

Epson

Epson 1520 - Stylus Color Inkjet Printer Manuel utilisateur

Epson

Epson Stylus Photo P50 Guide de l'utilisateur

Epson

Epson AcuLaser CX29NF Manuel utilisateur

Epson

Epson Fast T-Jet 3 PLUS Manuel utilisateur

Epson

Epson Stylus COLOR 460 Manuel utilisateur

Epson

Epson TM-U590/U590P Manuel utilisateur

Epson

Epson LQ-580 Manuel utilisateur

Epson

Epson EX-1000 Manuel utilisateur

Epson

Epson STYLUS PHOTO 915 Manuel utilisateur

Epson

Epson 2000P - Stylus Photo Color Inkjet Printer Manuel utilisateur

Epson

Epson 5700i - EPL B/W Laser Printer Manuel utilisateur

Epson

Epson AL-C500 Series Manuel utilisateur

Epson

Epson Stylus 400 - Ink Jet Printer Manuel d'installation et d'exploitation

Epson

Epson Stylus Photo 1270 Manuel utilisateur

Epson

Epson STYLUS CX4500 Manuel utilisateur

Epson

Epson SC-S30600 Manuel utilisateur

Epson

Epson LQ-2550 Manuel utilisateur

Epson

Epson EPL-6100L Manuel utilisateur

Epson

Epson Stylus Pro 9600 Photographic Dye Ink Manuel utilisateur

Epson

Epson LQ-300 - Impact Printer Manuel utilisateur

Epson

Epson LQ-590 Manuel utilisateur

Epson

Epson 980N - Stylus Color Inkjet Printer Mode d’emploi

Epson

Epson K100 Mode d’emploi

Epson

Epson TM-S9000II-NW Manuel d'utilisation et d'entretien

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur