Epson 5700i - EPL B/W Laser Printer Manuel utilisateur

EPSON EPL-5700i

9/99 EPSON EPL-5700i - 1

Printer Specifications

Printing

Printing method: Laser beam scanning and dry

electrophotographic process

Resolution: 600 dpi ×600 dpi, 300 dpi ×300 dpi

Printing speed: Up to 8 pages per minute, depending on

the font and print quality

First print: Less than 19 seconds with letter/A4

Warm-up time: About 20 seconds at normal temperature

Paper feed: Automatic feed

Paper feed

alignment: Center alignment for all sizes

RAM: 2MB, expandable up to 13MB

Input paper Up to 150 sheets in the tray

supply Up to 500 sheets per optional

([20 lb] 75 g/m2500-sheet lower cassette unit

paper): Up to 10 envelopes

Paper output: Face down or face up optional selection

Paper output Face down 100 sheets

capacity: Face up 20 sheets with the optional

face-up tray

Paper

* The minimum margin for all paper sizes is 0.16 inch (4 mm) for all

sides.

Environmental

Mechanical

parallel interface connector

AC inlet

USB

interface

connector

paper path selector

paper tray

manual feed slot

power switch

latch

output tray

extension

error light

(red)

printer cover

ready light

(green)

Type Weight Size*

Plain paper 16 to 24 lb,

60 to 90 g/m2

Letter (8.5 ×11 inches)

Legal (8.5 ×14 inches)

Executive (7.25 ×10.5 inches)

A5 (148 ×210 mm)

A4 (210 ×297 mm)

B4 (257 ×364 mm)

B5 (182 ×257 mm)

Half-Letter (5.5 ×8.5 inches)

Government Letter (8.0 ×10.5 inches)

Government Legal (8.5 ×13 inches)

F4 (210 ×330 mm)

Custom (3.0 ×5.0 inches to 8.5 ×14

inches)

Thick paper 28 to 58.5 lb,

105 to 220 g/m2

3.5 ×5.5 inches to 13 ×19 inches

Envelopes 16 to 28 lb,

60 to 105 g/m2

Monarch (3.875 × 7.5 inches)

Commercial 10 (4.125 ×9.5 inches)

DL (110 ×220 mm)

C5 (162 ×229 mm)

C6 (114 ×162 mm)

International B5 (176 ×250 mm)

Specification Operation Storage

Temperature 50 to 95 °F (10 to 35 °C) 32 to 95 °F (0 to 35 °C)

Humidity 15 to 85% RH 30 to 85% RH

Altitude 8200 feet (2500 meters) maximum

Height 9.9 inches (251 mm)

Width 15.6 inches (397 mm)

Depth 18.2 inches (463 mm)

Weight Approx. 14.5 lb (7.5 kg), excluding developer cartridge,

photoconductor unit, and options

Durability 5 years or 180,000 sheets, whichever comes first

EPSON EPL-5700i

2 - EPSON EPL-5700i 9/99

Electrical

Interfaces

Parallel interface: IEEE 1284-B compliant

USB interface: Universal Serial Bus 1.0 compliant.

Only Macintosh®and Windows®98 pre-

installed PCs support the USB interface.

Consumables Specifications

* Under the following conditions: Letter or A4 size paper,

continuous printing, and 5% print ratio

The number of pages you can print with a developer cartridge or a

photoconductor unit varies depending on the type of printing. If

you print a few pages at a time or print dense text exceeding the

5% print ratio, the unit may print fewer pages. The 5% print ratio

is equivalent to printing double-spaced standard text.

Option Specifications

500-Sheet Lower Cassette Unit

Paper size: Letter (C812881)

A4 (C812871)

Paper weight: 16 to 24 lb (60 to 90 g/m²)

Paper feed: Automatic feed

Tray capacity up to 500 sheets (20 lb or

75 g/m² paper)

Paper feed speed: For the first sheet, 21 seconds or less;

subsequent sheets, 8 pages per minute

Paper types: Plain paper, such as copier paper, and

recycled paper

Power supply: 5 Vdc supplied by the printer

Height: 4.7 inches (120 mm)

Width: 15.4 inches (397 mm)

Depth: 18.6 inches (472 mm ) including the tray

Weight: 9.3 lb (4.2 kg) including the tray

Face-up Tray (C812861)

Dimensions include printer

Height: 17.0 inches (433 mm)

Width: 15.4 inches (397 mm)

Depth: 22.8 inches (580 mm)

Weight: 0.7 lb (0.3 kg)

Paper output 20 sheets (20 lb or 75 g/m²paper)

capacity:

Loading Paper in the Standard Tray

1. Insert the paper tray into the slots at the front of the printer,

then push it all the way into the printer.

2. Fan a stack of paper (up to 150 sheets), then align the edges

by tapping the stack on a flat surface. With the paper’s

printable side facing up, place the stack into the tray. Slide

the paper guides against the paper stack.

Specification 110 V model 230 V model

Vo lt a ge 90 to 132 V 198 to 264 V

Rated frequency 50 to 60 Hz ± 3 Hz 50 to 60 Hz ± 3 Hz

Rated current 5.3 A 3 A

Power consumption Less than 580 W

Power consumption in

standby mode (no options

installed)

Less than 30 W

Part Shelf life

Approximate

life*

Storage

temperature

Storage

humidity

Developer

cartridge

18 months

after

production

Up to 6,000

pages

32 to 95 °F

(0 to 35 °C)

30 to 85%

Photocon-

ductor unit

Up to 20,000

pages

EPSON EPL-5700i

9/99 EPSON EPL-5700i - 3

3. Place the cover on the paper tray.

4. Pull up the output tray extension on the front of the printer.

Note:

Before printing, make sure the Paper Size setting in your printer driver

matches the paper you loaded.

Using the Optional 500-Sheet Lower

Cassette Unit

The optional 500-sheet lower cassette unit (C812881 for

letter size paper, C812871 for A4 size paper) gives you a

second paper source in addition to the standard paper tray.

Installing the Unit

1. Turn off the printer.

2. Unplug the printer’s power cord from the electrical outlet

and from the printer.

3. Disconnect all interface cables from the interface

connectors.

4. Make sure the printer and cassette are facing the same way.

Lift the printer and align the pins on the cassette with the

holes on the bottom of the printer. Then lower the printer

until it rests securely on the Lower Cassette Unit.

5. Reconnect any interface cables you removed.

6. Make sure the printer’s power switch is turned off, then

plug the power cord into the printer and into an electrical

outlet.

7. Turn on the printer.

Be sure to select the paper source in your application program.

Since the selection method varies from application to

application, see your software documentation for more

information.

Loading Paper

1. Pull out the paper tray from the paper cassette.

2. Press down the plate in the paper tray until it locks into

position.

3. Fan a stack of paper and tap it on a flat surface to even the

edges. Insert the paper printable side up into the tray,

making sure the paper fits under the tab as shown.

EPSON EPL-5700i

4 - EPSON EPL-5700i 9/99

4. Insert the paper tray in the paper cassette.

Using the Optional Face-up Tray

The printer normally outputs paper face down on top of the

printer. If you want face-up output, you can install the

optional face-up tray (C812861). This tray gives you

immediate viewing of your printed output and is

recommended for printing on media such as labels and

transparencies that require a straight-through paper path.

1. Turn off the printer.

2. Install the face-up tray by inserting the mounting pins into

the corresponding holes, one at a time. Do not force both

sides in at once.

The printer is factory set for face-down output. To switch the

paper path from face-down to face-up, use the selector located

on the right side of the printer near the back.

Using an Optional Memory Module

By installing a Single In-line Memory Module (SIMM), you

can increase printer memory up to 13MB. You may want to

add additional memory if you are having difficulty printing

complex graphics or if you regularly use numerous

downloaded fonts.

Note:

The maximum amount of memory is 13MB. Even if a 16MB SIMM is

installed, only 13MB is accessible.

You can purchase SIMMs from many vendors. Be sure that

the SIMM you purchase meets the following requirements:

❏72-pin, EDO or FPM type

❏Capacity of 4, 8, or 16MB

❏Access speed of 60 ns (nanoseconds) or less

❏Dimensions within 4.25 inches (108 mm) ×1.5 inches

(38 mm), with a thickness of 0.4 inch (10 mm)

Follow these steps to install a memory module:

1. Turn off the printer.

Warning:

To avoid electrical shock, do not attempt to install a SIMM unless

the printer is turned off.

2. Unplug the power cord from the electrical outlet.

3. Turn the printer so that its right side faces you.

4. Open the printer cover by pressing the latch on the left side

of the printer.

EPSON EPL-5700i

9/99 EPSON EPL-5700i - 5

5. Remove the printer’s side cover by lifting the clip and

sliding the side cover backward. Then lift the side cover

away from the printer.

6. Loosen the retaining screws securing the shield cover, and

remove the cover.

Caution:

Before you install the module, be sure to discharge any static

electricity by touching the printer’s shield cover while it’s still

attached to the printer (or touch any other part of the shield plate).

Otherwise, you may damage static-sensitive components.

7. Insert the SIMM module into the RAM slot at an angle,

making sure the pin numbers (either 1 or 72) of the slot and

the SIMM match.

8. Press the module forward until it clicks into place at a right

angle to the board. Do not apply too much force.

9. Replace the shield cover and tighten its screws.

10. Replace the printer’s side cover by inserting the side cover’s

hooks into the case’s slots and sliding the side cover

forward.

11. Gently close the printer cover.

12. Plug the power cord back in and turn on the printer.

If an incorrect amount of memory is shown on the status

sheet, turn off the printer and review the steps above to make

sure you correctly installed the SIMM. If the amount of

memory is still incorrect, contact your dealer or a qualified

service person for assistance.

Note:

The maximum amount of memory is 13MB. Even if a 16MB SIMM is

installed, only 13MB is accessible.

EPSON EPL-5700i

6 - EPSON EPL-5700i 9/99

Replacing Consumable Products

Your printer uses two consumable components, which are

listed below along with their approximate life expectancies.

❏Developer cartridge (S050010)

Up to 6,000 pages, depending on the complexity of your

print jobs

❏Photoconductor unit (S051055)

Up to 20,000 pages, depending on the complexity of your

print jobs

Replace the developer cartridge if you notice a decline in print

quality. Replace the photoconductor unit only if print quality

problems remain after replacing the developer cartridge.

Replacing the Developer Cartridge

Follow these steps to replace the developer cartridge.

1. Make sure the printer is turned off.

2. Open the printer cover by pressing the latch on the left side

of the printer and lifting the cover up all the way.

Caution:

You must completely open the printer cover when replacing the

developer cartridge; otherwise, you may damage the printer.

Warning:

Opening the printer cover exposes the fuser, which is marked

“CAUTION Hot Surface Avoid Contact.” Be careful not to touch the

fuser. If the printer has been in use, the fuser may be very hot.

3. Hold the cartridge by the handle and pull it straight up and

out of the printer.

Caution:

When removing the developer

cartridge, never touch the developing

roller under the flap; otherwise, the

print quality may be impaired.

4. Dispose of the used developer cartridge properly.

Caution:

Do not turn the developer cartridge upside down or tilt it from side to

side.

5. Remove the new developer cartridge from its bag. While

holding the cartridge horizontally, gently shake it a few

times from side to side and then from front to back to

distribute the toner evenly.

EPSON EPL-5700i

9/99 EPSON EPL-5700i - 7

6. Remove the protective tape seal from the cover of the

developer cartridge.

Caution:

Never touch the developing roller under

the flap. Otherwise, the print quality may

be impaired.

7. Hold the cartridge by its handle and lower it into the

printer, making sure that the pins on each side of the

cartridge fit into the grooves inside the printer. Slide the

cartridge gently into the opening until it locks into place.

8. Gently press down on the printer cover until it clicks shut.

9. After turning on the printer, access the printer settings

dialog box in the printer driver, and click the Toner Level

Clear button. The Toner level clear dialog box is displayed.

10. Click OK to reset the toner level counter.

Whenever you replace the developer cartridge, you should

clean the paper roller as described in “Cleaning the Inside of

the Printer” on page 11.

Replacing the Photoconductor Unit

1. Make sure the printer is turned off.

2. Open the printer cover by pressing the latch on the left side

of the printer and lifting the cover up all the way.

Caution:

You must completely open the printer cover to replace the

photoconductor unit; otherwise, you may damage the printer.

3. Remove the developer cartridge (see the previous section for

instructions).

Caution:

Do not turn the developer cartridge upside down or tilt it from side to

side.

Warning:

Opening the printer cover exposes the fuser, which is marked

“CAUTION Hot Surface Avoid Contact.” Be careful not to touch the

fuser. If the printer has been in use, the fuser may be very hot.

EPSON EPL-5700i

8 - EPSON EPL-5700i 9/99

4. Slide the photoconductor unit gently out of the printer.

5. Remove the new photoconductor unit from its bag.

Caution:

Never touch the photoconductor

unit’s light-sensitive drum;

otherwise, print quality may be

impaired.

6. Insert the pins on each side of the new photoconductor unit

into the grooves inside the printer. Slide the unit gently into

the opening until it locks into place.

7. Reinstall the developer cartridge.

8. Press down the printer cover until it clicks shut.

9. After turning on the printer, access the printer settings

dialog box in the printer driver, and click the OPC Level

Clear button. The OPC level clear dialog box is displayed.

10. Click OK to reset the Photoconductor level counter.

Ready and Error Lights

The ready (green) and error (red) lights on the top of the

printer indicate the status of the printer, as described in the

following table:

Paper Feeding Problems

Preventing Paper Feed and Paper Jam

Problems

If you have frequent paper feed or paper jam problems, try the

following:

❏Fan the stack of paper and then tap its edges to align them

before loading.

❏Don’t overfill the paper tray.

❏Be sure to adjust the paper guides so that the paper feeds

correctly.

❏Never allow more than 100 sheets to accumulate on the

output tray.

❏Try turning over the stack of paper in the paper tray. Most

paper packages indicate the best side for printing.

Ready light

(green)

Error light

(red) Printer status

Off Off Printer is off.

On Off Printer is ready.

Flashing Off Printer is warming up or receiving data.

Off Flashing Printer is out of paper or has a paper jam.

Off On Printer may require a service call. Try turning

off the printer and then turning it back on. If

this does not remedy the error, contact your

dealer or a qualified service person.

EPSON EPL-5700i

9/99 EPSON EPL-5700i - 9

Clearing Paper Jams

The following steps describe how to remove paper when it is

jammed as shown below. Other types of paper jams are

described in later sections.

1. Make sure the printer is turned off.

2. Open the printer cover by pressing the latch on the left side

of the printer and lifting the cover up all the way.

Warning:

Opening the printer cover exposes the fuser, which is marked

“CAUTION Hot Surface Avoid Contact.” Be careful not to touch the

fuser. If the printer has been in use, the fuser may be very hot.

3. Remove the developer cartridge.

Caution:

When removing the developer

cartridge, never touch the developing

roller under the flap; otherwise, the

print quality may be impaired.

4. Remove the photoconductor unit.

Caution:

Never touch the photoconductor

unit’s light-sensitive drum;

otherwise, the print quality

may be impaired.

jammed paper

CAUTION Hot Surface Avoid Contact

EPSON EPL-5700i

10 - EPSON EPL-5700i 9/99

5. Remove any paper from the paper path.

Note:

If paper is jammed at the fuser, grasp the bottom of the paper and

pull it out.

6. Reinstall the photoconductor unit, then the developer

cartridge.

7. Close the printer cover.

Printing automatically restarts from the page that jammed.

If the error light (red) continues flashing after removing all

jammed paper, open and close the printer cover to clear the

error.

Clearing Feed Jams

Paper may jam when feeding from the standard or optional

paper tray, as shown below.

1. Remove the paper tray cover and all the paper from the

paper tray.

2. Carefully remove any sheets that have fed partway into the

printer.

3. Open the printer cover. Remove any pieces of paper that

may have torn off or are remaining in the printer.

If necessary, remove the developer cartridge and

photoconductor unit, and any paper left in the paper feed

path. Then reinsert the cartridge and the unit.

4. Tap the edges of the paper stack on a flat surface and

carefully reload it into the paper tray. (Do not reload curled

or wrinkled sheets.) Then reinstall the paper tray cover.

5. Close the printer cover. The jammed page is automatically

reprinted.

jammed paper

Autres manuels pour 5700i - EPL B/W Laser Printer

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Epson Imprimante

Epson

Epson L200 Manuel d'exploitation et d'entretien

Epson

Epson NPD4909-01 Manuel utilisateur

Epson

Epson SC-T3170X SP Mode d’emploi

Epson

Epson FX-1180 - Impact Printer Manuel utilisateur

Epson

Epson ColorPage EPL-C8200 Manuel utilisateur

Epson

Epson Stylus Color 660 Manuel utilisateur

Epson

Epson PictureMate PM 235 Mode d’emploi

Epson

Epson TM-T70II Manuel d'installation et d'exploitation

Epson

Epson R2400 - Stylus Photo Color Inkjet Printer Manuel utilisateur

Epson

Epson 1520 - Stylus Color Inkjet Printer Fiche technique

Epson

Epson Stylus C83 Manuel utilisateur

Epson

Epson ELP-N2550 Guide de référence rapide

Epson

Epson R300 - Stylus Photo Color Inkjet Printer Manuel utilisateur

Epson

Epson Perfection 1200PHOTO Manuel utilisateur

Epson

Epson XP-3200 Series Manuel utilisateur

Epson

Epson XP-8700 Series Manuel utilisateur

Epson

Epson LabelWorks LW-Z5000 Series Manuel utilisateur

Epson

Epson Office BX310FN Series Mode d’emploi

Epson

Epson SureColor P600 Series Manuel utilisateur

Epson

Epson WorkForce ST-C8000 Manuel utilisateur

Epson

Epson FX-2190N Manuel utilisateur

Epson

Epson Stylus Color IIs Manuel utilisateur

Epson

Epson Stylus PHOTO 1290 Manuel utilisateur

Epson

Epson Workforce Pro WF-C8610 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur