Epilog Laser MINI Manuel utilisateur

EPILOG LASER

16371 Table Mountain Parkway

Golden, Colorado 80403

Phone 303-215-9171 - FAX 303-277-9669

www.epiloglaser.com

REPLACING THE LASER TUBE IN THE

EPILOG MINI ENGRAVER

Tools needed: Phillips head screwdriver #1

1. Turn engraver off and unplug

2. Facing the back of the machine, remove the 9 screws using the Phillips head screwdriver on the

back panel. (PIC 1)

3. The laser tube is silver in color and sits directly above the exhaust outlet. Disconnect the gray

communication cable from the left side of the laser tube by pressing the plastic tab on it and pulling

it free from the laser tube itself. (PIC 2)

4. Next, disconnect the black and red wire connection located on the left side of the laser tube by

unplugging it from the wiring harness. To do this, simply press down on the plastic tab of the

connector and pull free from the plug of the wiring harness. (PIC 3)

1 2 3

5. You will now need to unplug the Red Dot pointer. This is located on the right side of the laser

tube. There is a small red and black wire that comes from the diode and connects to a black

connector. Disconnect this connector by pressing on the plastic tab and pulling the connector free.

(PIC 4).

6. Now locate the Phillips head screw with the green ring around it located just up and to the left of

where you disconnected the 2 connections mentioned in steps 3 and 4. Using the Phillips head

screwdriver, loosen this screw until it stops. The screw will not drop out and is held to the bracket

with the green ring. (PIC 5)

7. Now locate the Phillips head screw with the green ring on the right side of the laser tube. There

is one on the top and one on the bottom. (PIC 6, 7) Loosen both of these until the screw stops.

5 6 7

8. The laser tube can now slide on the pin located above the green ringed Phillips head screw on

the left of the tube and the pin located to the left of the green ringed Phillips head screw on the

upper right side of the laser tube. This one will be hard to see as it located behind the cooling fins

of the laser tube. The laser tube now needs to slide to the left until it stops.

10. The laser can now be pulled free from the back of the machine.

11. You will need to remove the red and black wire power harness from the left side of the laser

tube and install it on the new laser tube. To do this, simply remove the 2 screws using the Phillips

head screwdriver that secure the power harness to the 2 terminals located on the left side of the

laser tube. Make sure the orientation of the black and red wires are the same when installing back

onto the new laser tube.

12. To install the new laser tube, simply reverse steps 10 back down to 1.

If you have any further questions regarding this procedure, please contact Epilog Technical

support at the following:

Phone 303-215-9171

Fax 303-531-7594

Email [email protected]

Autres manuels pour MINI

Table des matières

Autres manuels Epilog Laser Graveur

Epilog Laser

Epilog Laser FiberMark Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Manuel utilisateur

Epilog Laser

Epilog Laser Zing Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Helix Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Fusion 13000 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser MINI Manuel utilisateur

Epilog Laser

Epilog Laser Edge 12 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser MINI Manuel utilisateur

Epilog Laser

Epilog Laser Mini Series Manuel utilisateur

Epilog Laser

Epilog Laser Zing Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser MINI 18 Manuel utilisateur

Epilog Laser

Epilog Laser Edge 12 Manuel utilisateur

Epilog Laser

Epilog Laser Helix Manuel d'installation et d'exploitation

Epilog Laser

Epilog Laser LEGEND 24EX 6000 Manuel utilisateur

Manuels Graveur populaires d'autres marques

COMGROW

COMGROW COMGO Z1 Manuel utilisateur

BAUKER

BAUKER EG013 Manuel utilisateur

GRAVOGRAPH

GRAVOGRAPH LS900 XP Mode d'emploi

iMARC

iMARC VET TAG Engraver Manuel utilisateur

Dremel

Dremel 3000 Operating/s Manuel utilisateur

iMARC

iMARC Pet Tag Engraver Manuel utilisateur

PT W50036 Manuel utilisateur

Omtech

Omtech USB3020A Manuel utilisateur

Ortur

Ortur Laser Master 2 Manuel utilisateur

Vision

Vision VE-810 Manuel utilisateur

Omtech

Omtech POLAR 350 Manuel utilisateur

Vision

Vision Cylindrical Manuel utilisateur

SCULPFUN

SCULPFUN S6 Manuel utilisateur

Redsail

Redsail M500 Guide de configuration rapide

Dremel

Dremel 290 Instructions de montage

Vision

Vision MaxPro Manuel utilisateur

Vision

Vision 5 Series Manuel utilisateur

SFX

SFX SFX-GS Manuel utilisateur