Epilog Laser FiberMark Manuel utilisateur

EPILOG LASER

16371 Table Mountain Parkway

Golden, Colorado 80403

Phone 303-215-9171 - FAX 303-277-9669

www.epiloglaser.com

Procedure: Replacing the Controller Board

Machine Type: FiberMark

Tools Required: Phillips head screw driver

NOTE: Your replacement controller board was shipped to you in an anti-

static bag to protect the controller board from being damaged by static

electricity.

Do not handle the controller board without wearing the included

anti static strap.

Place the defective controller board in the anti-static bag before

returning it to Epilog.

NOTE: If the machine will still boot, before you remove the board please

follow steps 1 and 2. This will save you a lot of set up time when the

new board is installed.

If the board will not boot up skip to step 4, the controller board

that you have been sent has been programmed with the settings that were

used to set your machine up originally.

1. If the machine will still boot up, before you remove the

controller board, please record the following information from

the Function and Configuration menus of the machine. To access

the function menu in the engraver depress both the “GO” and

the “Pointer” buttons on the display.

Serial Number

IP Address

Subnet Mask

Gateway

2. From the Configuration menu you will need to record the

following information.

X-Home

Y-Home

XR Home

YR Home

Laser Match

System unit

3. Turn off the engraver and disconnect the engraver from its

power source.

4. The Controller Board is located on the right side of the

machine when you are standing in front of the machine.

5. Remove the right hand side cover which is held on by six

Phillips head screws. Four on the side and two on the rear of

the machine.

6. Locate the Controller Board. The board is on the right hand

rear side of the engraver.

7. There are 8 cables/wires that plug into the controller board.

All of these wires will need to be unplugged. See picture 1

Picture 1

8. There is one connection (labeled #1 in picture 1) which has a

metal clamp that secures it in place. Remove the two Phillips

head screws shown in Picture 2. Remove this connector from the

board.

Picture 2

9. Included in the controller board shipment was an Anti-Static

strap. Please follow the instructions on the wearing the

anti-static strap. Static electricity can damage the

controller boards.

10. Located in each corner of the controller board are mounting

screws. Remove the four mounting screws which secure the

controller board and remove the board from the machine.

11. When installing the new Controller Board, start with the

screws which hold it in place and then reattach the

cables/wires.

***NOTE***Once all of this has been done and you are about to put

the side panel back on make sure there are no cables/wires that

could prevent the side from fitting properly.

If you are still having issues with this please feel free to

contact Epilog Technical Support.

Phone: 303-215-9171

Fax: 303-277-9669

E-mail: [email protected]

Autres manuels pour FiberMark

Table des matières

Autres manuels Epilog Laser Graveur

Epilog Laser

Epilog Laser Fusion Manuel d'utilisation et d'entretien

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Mini Series Manuel utilisateur

Epilog Laser

Epilog Laser MINI Manuel utilisateur

Epilog Laser

Epilog Laser Zing Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Fusion 13000 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion M2 32 Manuel utilisateur

Epilog Laser

Epilog Laser Helix Manuel d'installation et d'exploitation

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser MINI Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Pro 32 Manuel utilisateur

Epilog Laser

Epilog Laser FusionPro 16000 Manuel utilisateur

Epilog Laser

Epilog Laser Zing Manuel utilisateur

Epilog Laser

Epilog Laser Fusion Manuel utilisateur

Epilog Laser

Epilog Laser Edge 12 Manuel utilisateur

Epilog Laser

Epilog Laser FiberMark Manuel utilisateur

Manuels Graveur populaires d'autres marques

COMGROW

COMGROW COMGO Z1 Manuel utilisateur

BAUKER

BAUKER EG013 Manuel utilisateur

GRAVOGRAPH

GRAVOGRAPH LS900 XP Mode d'emploi

iMARC

iMARC VET TAG Engraver Manuel utilisateur

Dremel

Dremel 3000 Operating/s Manuel utilisateur

iMARC

iMARC Pet Tag Engraver Manuel utilisateur

PT W50036 Manuel utilisateur

Omtech

Omtech USB3020A Manuel utilisateur

Ortur

Ortur Laser Master 2 Manuel utilisateur

Vision

Vision VE-810 Manuel utilisateur

Omtech

Omtech POLAR 350 Manuel utilisateur

Vision

Vision Cylindrical Manuel utilisateur

SCULPFUN

SCULPFUN S6 Manuel utilisateur

Redsail

Redsail M500 Guide de configuration rapide

Dremel

Dremel 290 Instructions de montage

Vision

Vision MaxPro Manuel utilisateur

Vision

Vision 5 Series Manuel utilisateur

SFX

SFX SFX-GS Manuel utilisateur