Epever XTRA1206N Manuel utilisateur

MPPT Solar Charge Controller

User Manual

Models:

XTRA1206N/XTRA2206N

XTRA1210N/XTRA2210N

XTRA3210N/XTRA4210N

XTRA3215N/XTRA4215N

XTRA3415N/XTRA4415N

Important Safety Instructions

Please keep this manual for future review.

This manual contains all instructions of safety, installation and operation for XTRA N series

Maximum Power Point Tracking (MPPT) controller ("the controller" as referred to in this manual).

General Safety Information

Read carefully all the instructions and warnings in the manual before installation.

No user serviceable components inside the controller. DO NOT disassemble or attempt to

repair the controller.

Mount the controller indoors. Avoid exposure the components and do not allow water to enter

the controller.

Install the controller in a well ventilated place. The controller’s heat sink may become very hot

during operation.

Suggest installing appropriate external fuses/breakers.

Make sure to switch off all PV array connections and the battery fuse/breakers before

controller installation and adjustment.

Power connections must remain tight to avoid excessive heating from loose connection.

 
CONTENTS 
General Information.........................................................................1 
1 Overview........................................................................................................ 1 
2 Characteristics ............................................................................................... 2 
3 Naming Rules................................................................................................. 3 
4 Product Classification..................................................................................... 3 
Installation........................................................................................5 
1 Attentions....................................................................................................... 5 
2 PV Array Requirements.................................................................................. 5 
3 Wire Size........................................................................................................ 9 
4 Mounting...................................................................................................... 11 
Display units ..................................................................................14 
1 Basic Display unit(XDB1).............................................................................. 14 
2 Standard Display unit (XDS1)....................................................................... 15 
3 Adanced Display unit (XDS2) ....................................................................... 19 
Parameters Setting........................................................................25 
1 Battery parameters....................................................................................... 25 
1.1 Supported battery types................................................................................................ 25 
1.2 Local setting.................................................................................................................. 25 
1.3 Remote Setting ............................................................................................................. 28 
2 Load working modes .................................................................................... 31 
2.1 LCD setting ................................................................................................................... 31 
2.2 RS485 communication setting ...................................................................................... 33 
Others.............................................................................................35 
1 Protection..................................................................................................... 35 

5.2 Troubleshooting............................................................................................ 37

5.3 Maintenance................................................................................................. 39

6 Technical Specifications...............................................................40

Annex I Conversion Efficiency Curves ...........................................44

1 General Information

1.1 Overview

XTRA N series controller which can carry different display units(XDB1/XDS1/XDS2) adopt the

advanced MPPT control algorithm, it can minimize the maximum power point loss rate and loss

time, quickly track the maximum power point(MPP) of the PV array and obtain the maximum energy

from solar array under any conditions; and it can increase the ratio of energy utilization in the solar

system by 20%-30% compared with PWM charging method.

Limiting the charging power & current and reducing charging power functions ensure the system

stable with over PV modules in high temperature environment. IP33 Ingress protection and isolated

RS485 design further improve the controller’s reliability and meet the different application

requirements.

XTRA N series controller owns self-adaptive three-stage charging mode based on digital control

circuit, which can effectively prolong the lifespan of battery and significantly improve the system

performance. It also has comprehensive electronic protection for overcharge, overdischarge, PV &

battery reverse polarity etc, to ensure the solar system more reliable and more durable. This

controller can be widely used for RV, household system, field monitoring and many other

applications.

Features：

CE certification(LVD EN/IEC62109,EMC EN61000-6-1/3)

100% charging and discharging in working environment temperature range

Optional LCD display units (XDB1/XDS1/XDS2)

High quality and low failure rate components of ST or IR to ensure service life

Advanced MPPT technology & ultra-fast tracking speed guarantee tracking efficiency up to

99.5%

Maximum DC/DC transfer efficiency is as high as 98.5%★, full load efficiency is up to 97.2%★

Advanced MPPT control algorithm to minimize the MPP lost rate and lost time

Accurate recognizing and tracking of multi-peaks maximum power point

Wide MPP operating voltage range

Support the lead-acid and lithium batteries; voltage parameters can be set on the controller

Programmable temperature compensation

Limit charging power & current over rated value

Real-time energy statistics function

Power reduction automatically over temperature value

Multiple load work modes

Comprehensive electronic protection

Isolated RS485 with 5V/200mA protected output for no power devices, with Modbus protocol

Support monitoring and setting the parameters via APP or PC software

IP33▲Ingress protection

★XTRA4415N@48V system

For the BCV, FCV, LVD, and LVR, users can modify them on the local controller when the

battery type is "USE."

▲3-protection against solid objects: protected against solids objects over 2.5mm.

3-protected against sprays to 60°from the vertical.

1.2 Characteristics

Figure 1 Product Characteristics

❶

RTS★port

❺

RS485 communication port

❷

PV Terminals

❻

Terminal protection cover

❸

Battery Terminals

❼

Display units

❹

Load Terminals

❽

Mounting Hole Φ5mm

★If the temperature sensor is short circuit or damaged, the controller will charge or

discharge according the voltage setting point at the default temperature setting of 25 ºC(no

temperature compensation).

1.3 Naming Rules

XTRA 1 2 10 N - XDS2

Display Unit(XDB1/XDS1/XDS2)

Product Series

Charge & discharge current 1-10A;2-20A;3-30A;4-40A

System Voltage 1-12VDC; 2-12/24VDC

Max. PV open circuit voltage 10-100V;15-150V

Common Negative System

1.4 Product Classification

Classify

Model

Picture

Display

Basics

XTRA****N-XDB1

LED Indicators: PV & battery working

status

Button:

In manual work mode, it switch

ON/OFF the load by press the

button.

Clear the error information.

Standard

XTRA****N-XDS1

LED Indicators: PV & load working

status

Buttons: View or set the parameters

or clear the error information.

LCD：PV display:voltage/current

/generated energy

Battery display:

voltage/current/temperature

Load display:

current/consumed energy/load working

mode

Advanced

XTRA****N-XDS2

LED Indicators: PV & battery & load

working status

Buttons: View or set the parameters

or clear the error information.

LCD: PV display:voltage/current

/generated energy/power

Battery display:voltage/current/

temperature/capacity

Load display: voltage/current/power

/consumed energy/load working mode

2 Installation

2.1 Attentions

Please read the entire installation instructions to get familiar with the installation steps before

installation.

Be very careful when installing the batteries, especially flooded lead-acid battery. Please wear

eye protection, and have fresh water available to wash and clean any contact with battery acid.

Keep the battery away from any metal objects, which may cause short circuit of the battery.

Explosive battery gases may come out from the battery during charging, so make sure

ventilation condition is good.

Ventilation is highly recommended if mounted in an enclosure. Never install the controller in a

sealed enclosure with flooded batteries! Battery fumes from vented batteries will corrode and

destroy the controller circuits.

Loose power connections and corroded wires may result in high heat that can melt wire

insulation, burn surrounding materials, or even cause fire. Ensure tight connections and use

cable clamps to secure cables and prevent them from swaying in mobile applications.

The controller can work with lead-acid battery and lithium battery within its control scope.

Battery connection may be wired to one battery or a bank of batteries. The following instructions

refer to a singular battery, but it is implied that the battery connection can be made to either one

battery or a group of batteries in a battery bank.

Multiple same models of controllers can be installed in parallel on the same battery bank to

achieve higher charging current. Each controller must have its own solar module(s).

Select the system cables according to 5A/mm2or less current density in accordance with Article

690 of the National Electrical Code, NFPA 70.

2.2 PV Array Requirements

(1) Serial connection (string) of PV modules

As the core component of solar system, controller could be suitable for various types of PV

modules and maximize converting solar energy into electrical energy. According to the open circuit

voltage (Voc) and the maximum power point voltage (VMpp) of the MPPT controller, the series

number of different types PV modules can be calculated. The below table is for reference only.

XTRA1206N/2206N:

System

voltage

36 cell

Voc＜23V

48 cell Voc

＜31V

54 cell

Voc＜34V

60 cell

Voc＜38V

Max.

Best

Max.

Best

Max.

Best

Max.

Best

12V

24V

System

voltage

72 cell

Voc＜46V

96 cell

Voc＜62V

Thin-Film

Module

Voc＞80V

Max.

Best

Max.

Best

12V

24V

NOTE: The above parameter values are calculated under standard test conditions (STC (Standard

Test Condition)：Irradiance 1000W/m2，Module Temperature 25℃，Air Mass1.5.)

XTRA1210/2210/3210/4210N:

System

voltage

36 cell

Voc＜23V

48 cell

Voc＜31V

54 cell

Voc＜34V

60 cell

Voc＜38V

Max.

Best

Max.

Best

Max.

Best

Max.

Best

12V

24V

System

voltage

72 cell

Voc＜46V

96 cell

Voc＜62V

Thin-Film

Module Voc

＞80V

Max.

Best

Max.

Best

12V

24V

NOTE: The above parameter values are calculated under standard test conditions (STC (Standard

Test Condition)：Irradiance 1000W/m2，Module Temperature 25℃，Air Mass1.5.)

XTRA3215/4215N:

System

voltage

36 cell

Voc＜23V

48 cell

Voc＜31V

54 cell

Voc＜34V

60 cell

Voc＜38V

Max.

Best

Max.

Best

Max.

Best

Max.

Best

12V

24V

Autres manuels pour XTRA1206N

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Epever Contrôleurs

Epever

Epever LS LPLW Series Manuel utilisateur

Epever

Epever ViewStar AU Series Manuel utilisateur

Epever

Epever LandStar BPL Series Manuel utilisateur

Epever

Epever RC-10 Manuel utilisateur

Epever

Epever Tracer2606BPL Manuel utilisateur

Epever

Epever MPPT Manuel utilisateur

Epever

Epever Tracer-AN Series Manuel utilisateur

Epever

Epever Tracer1206AN Manuel utilisateur

Epever

Epever TRIRON N Series Manuel utilisateur

Epever

Epever LandStar LPLI Series Manuel utilisateur

Epever

Epever Tracer BPL Series Manuel utilisateur

Epever

Epever Tracer2606BPL Manuel utilisateur

Epever

Epever LS EPD Series Manuel utilisateur

Epever

Epever TRIRON1206N Manuel utilisateur

Epever

Epever SolarV TRIRON Series Manuel utilisateur

Epever

Epever LandStar GPLI Series Manuel utilisateur

Epever

Epever LandStar EU series Manuel utilisateur

Epever

Epever XTRA Series Manuel utilisateur

Epever

Epever Tracer BP Series Manuel utilisateur

Epever

Epever Tracer-AN Series Manuel utilisateur

Epever

Epever Tracer 4215BN Manuel utilisateur

Epever

Epever DuoRacer Series Manuel utilisateur

Epever

Epever LS-E Series Manuel utilisateur

Epever

Epever ViewStar VS1024AU Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur