Epever LS-E Series Manuel utilisateur

LS-E Series

—— Solar Charge Controller

EPEVER

USER

MANUAL

LS-E Series

—— Solar Charge Controller

Nominal System Voltage

LS0512E/LS1012E

12VDC

LS1024E/LS2024E

12/24VDC

Maximum PV Input

Voltage

LS0512E/LS1012E

30V

LS1024E/LS2024E

50V

Nominal

Charge/Discharge Current

LS0512E

LS1012E/LS1024E

10A

LS2024E

20A

LandStar

Contents

1 Important Safety Information..........................................1

2 General Information........................................................2

3 Installation Instructions...................................................3

3.1 Mounting...............................................................3

3.2 Wiring ...................................................................4

4 Operation........................................................................5

4.1 LED Indicators ......................................................5

4.2 Setting Operation...................................................7

5 Protection and Troubleshooting ......................................8

5.1 Protection ..............................................................8

5.2 Troubleshooting.....................................................9

6 Technical specifications................................................11

1 Important Safety Information

Read all of the instructions and cautions in the manual before

beginning installation.

There are no user serviceable parts inside the controller. Do not

disassemble or attempt to repair it.

Install external fuses/breakers as required.

Disconnect the solar module and fuse/breakers near to battery before

installing or adjusting the controller.

Do not allow water to enter the controller.

Confirm that power connections are tightened to avoid excessive

heating from loose connection.

2 General Information

LS-E series solar charge controller, with beautiful, economic, practical,

simple and easy to use, etc. It has various unique functions：

High efficient Series PWM charging, increase the battery lifetime

and improve the solar system performance.

Battery LED indicator can indicates battery situation.

Support 3 charging options: Sealed, Gel and Flooded.

Adopt temperature compensation, correct the charging and

discharging parameters automatically and improve the battery

lifetime.

Electronic protection: load overload and short circuit, battery over

discharging, over voltage, low voltage and reverse protection.

With humanized Settings, operation will be more comfortable and co

nvenient.

Industrial design, wide application range.

3 Installation Instructions

3.1 Mounting

Read through the entire installation section first before beginning

installation.

Be very careful when working with batteries. Wear eye protection.

Have fresh water available to wash and clean any contact with

battery acid.

Uses insulated tools and avoid placing metal objects near the

batteries.

Explosive battery gasses may be present during charging. Be certain

there is sufficient ventilation to release the gasses.

Avoid direct sunlight and do not install in locations where water can

enter the controller.

Loose power connections and/or corroded wires may result in

resistive connections that melt wire insulation, burn surrounding

materials, or even cause fire. Ensure tight connections and use cable

clamps to secure cables and prevent them from swaying in mobile

applications.

Use with Gel, Sealed or Flooded batteries only.

Battery connection may be wired to one battery or a bank of batteries.

The following instructions refer to a singular battery, but it is

implied that the battery connection can be made to either one

battery or a group of batteries in a battery bank.

Select the system cables according to 3.5A/mm2current density.

3.2Wiring

1. Connect components to the charge controller in the sequence as

shown in above picture and pay much attention to the “+”and

“-”.Always power the battery First.

2. After power the battery, check the battery indicator on the

controller, it will be green. If it’s not green, please refer to chapter

3. The load should be DC applicant with the same rated voltage as

battery’s. Controller offers power to loads through the battery

voltage.

4 Operation

4.1 Features

Charging and load status indicator Table 4-1

Indicator

Status

System

Status

Note

Charging

status

indicator

Charging

Normal

Fast

Flashing

Over

voltage

Refer to section 5

Load status

indicator

Load ON

Normal

OFF

Load OFF

Slowly

Flashing

Overload

When the load amp is

1.25times of rated

Charging status indicator

Load status indicator

LED1

Setting

button

Solar Module

Terminals

Battery

Terminals

Load

Terminals

Mounting

Holes

LED2

LED3

LED4

current for 60 seconds,

or the load amp is 1.5

times of rated current for

5 seconds

Fast

Flashing

Short Circuit

Refer to section 5

Battery status indicator(LED1、LED2、LED3、LED4)

Battery LED indicator(The parameters in the table below is for 12VDC

system at 25℃, for 24VDC system ,the parameters is doubled)

Table 4-2

LED1

LED2

LED3

LED4

Battery Status

Slowly

Flashing

Under voltage

Fast

Flashing

Over discharged

Battery LED indicator status during voltage is up

○

12.8V＜Ubat＜13.4V

○

13.4V＜Ubat＜14.1V

○

14.1V ＜Ubat

Battery LED indicator status during voltage is down

○

12.8V＜Ubat＜13.4V

○

12.4V＜Ubat＜12.8V

○

Ubat＜12.4V

“○”LED indicates on “×”LED indicates off “Ubat”battery voltage

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Epever Contrôleurs

Epever

Epever TRIRON N Series Manuel utilisateur

Epever

Epever LandStar EU series Manuel utilisateur

Epever

Epever Tracer-AN Series Manuel utilisateur

Epever

Epever XTRA Series Manuel utilisateur

Epever

Epever RC-10 Manuel utilisateur

Epever

Epever LS-B Series Manuel utilisateur

Epever

Epever LS LPLW Series Manuel utilisateur

Epever

Epever LS1024B Manuel utilisateur

Epever

Epever Tracer-AN Series Manuel utilisateur

Epever

Epever Tracer BPL Series Manuel utilisateur

Epever

Epever Tracer1206A Manuel utilisateur

Epever

Epever LS EPD Series Manuel utilisateur

Epever

Epever Tracer6210AN Manuel utilisateur

Epever

Epever Tracer BP Series Manuel utilisateur

Epever

Epever Tracer2206AN Manuel utilisateur

Epever

Epever Tracer2606BPL Manuel utilisateur

Epever

Epever iTracer-ND Series Manuel utilisateur

Epever

Epever XTRA-N Series Manuel utilisateur

Epever

Epever LandStar BPL Series Manuel utilisateur

Epever

Epever LandStar GPLI Series Manuel utilisateur

Epever

Epever ViewStar AU Series Manuel utilisateur

Epever

Epever XTRA1206N Manuel utilisateur

Epever

Epever Tracer BP Series Manuel utilisateur

Epever

Epever TRIRON1206N Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur