Epever TRACER 6420 Manuel utilisateur

612806420L1-18A August 2005 1

Converting the Frequency Plan of a TRACER 6420 System

Introduction

TRACER 6420 systems are shipped from the factory with the frequency plan programmed as Plan A or Plan B.

Each wireless link must contain a Plan A radio on one end and a Plan B on the other. A frequency plan

conversion may be performed in the field, but should only be attempted if absolutely necessary and must

always be performed by qualified personnel. This document outlines the procedure for changing the frequency

plan of a TRACER 6420 system.

Prerequisite Procedures

The current frequency plan configuration is listed on a label located on the rear panel of the unit (near the

Antenna connector). Record the current configuration before beginning this procedure.

Tools and Materials Required

• 5/16” Torque wrench (8 in-lbs)

• 3/16” nut driver

• Phillips-head screw driver

This document contains digital images showing connectors, cable routings, etc. Connector

placement and cable routings in the images will not be identical to your TRACER 6420

system. Follow the written procedure provided in this guide and refer to the images only

when instructed.

Disconnect all cables attached to the TRACER 6420 system (including power, data,

terminal RS-232, etc.) before performing this procedure.

Do not attempt to perform the conversion without the proper tools (see list below). Using

improper tools will damage the unit.

Electronic equipment can be damaged by static electrical discharge. Before handling

equipment, put on an antistatic discharge wrist strap to prevent damage to components.

Place equipment in antistatic packing material when transporting or storing. When

working on equipment, always place it on an approved antistatic mat that is electrically

grounded.

TRACER 6420 Frequency Conversion Document

1. Remove any installed modules from the chassis (blank panels covering the module slot openings do

not need to be removed).

2. Remove the screws from the chassis cover using a Phillips-head screwdriver (see Figure 1).

Figure 1. Removing the Cover Screws (TRACER 6420)

3. Carefully slide the cover toward the back of the unit until the front edge of the cover is disconnected

from the front of the unit. Lift the cover off and set aside.

4. Verify the current frequency plan configuration. To verify the plan, check the connections between the

J connectors (located on the edge of the board and labeled J1 and J2) and the Chan connectors

(located on the diplexer). The Chan connectors are labeled CH1 and CH2 for most TRACER 6420

systems. The following table outlines the connections for Plan A and B.

Click to see a digital image of the J connectors or the Chan connectors.

5. Using the torque wrench, disconnect both cables from the Chan connectors on the diplexer. Do not

attempt to disconnect the J connectors (located on the board) as this will cause damage. Click here for

a digital picture of this step.

Perform the steps below in the order listed.

Remove all connected mounting brackets before attempting to remove the unit cover.

TRACER 6420

PLAN CHAN 1 CHAN 2

AJ2 J1

BJ1 J2

TRACER 6420 Frequency Conversion Document

6. Carefully flex the cables to swap the connections. Be careful with the RF cables, making sure that the

minimum bend radius of the cable is greater than 0.75"; bends and loops smaller than a quarter will

cause the RF cable to break. Use the wiring guidelines in Figure 2 for help with wire placement.Click

here for a digital picture of this step.

Figure 2. TRACER 6420 Cable Routing Diagrams

7. Use the torque wrench to reconnect the RF cables to the Chan connectors. Tighten the cables by

turning clockwise until you hear a click from the wrench. DO NOT overtighten connectors as this will

cause the RF cable to break. The TRACER 6420 system will not operate properly with broken RF

cables.

8. Reinstall the cover and carefully tighten all screws.

9. Change label on back of the unit to reflect the Plan change.

Allowing the RF cables to sit on the processor and radio boards (green) could cause

damage to the boards; keep the RF cables off the boards while re-routing them. Click here

for a digital picture of this mistake.

PLAN B

J1 J2

CH 1CH 2

PLAN A

CH 1CH 2

>> BACK

Table des matières

Autres manuels Epever Contrôleurs

Epever

Epever Epsolar eBox-WIFI-01 Manuel utilisateur

Epever

Epever LandStar BPL Series Manuel utilisateur

Epever

Epever SolarV TRIRON Series Manuel utilisateur

Epever

Epever LS LPLI Series Manuel utilisateur

Epever

Epever LS EPD Series Manuel utilisateur

Epever

Epever XTRA N Series Manuel utilisateur

Epever

Epever LandStar EU series Manuel utilisateur

Epever

Epever XTRA Series Manuel utilisateur

Epever

Epever RC-10 Manuel utilisateur

Epever

Epever Tracer BPL Series Manuel utilisateur

Epever

Epever Tracer6210AN Manuel utilisateur

Epever

Epever Tracer BP Series Manuel utilisateur

Epever

Epever Tracer LPLI Series Manuel utilisateur

Epever

Epever Tracer BP Series Manuel utilisateur

Epever

Epever SolarV AN Series Manuel utilisateur

Epever

Epever XTRA1206N Manuel utilisateur

Epever

Epever DuoRacer Series Manuel utilisateur

Epever

Epever ViewStar VS1024AU Manuel utilisateur

Epever

Epever TRIRON N Series Manuel utilisateur

Epever

Epever Tracer2606BPL Manuel utilisateur

Epever

Epever TRIRON1206N Manuel utilisateur

Epever

Epever Tracer1206A Manuel utilisateur

Epever

Epever MPPT Manuel utilisateur

Epever

Epever Tracer BPL Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur