Envirovent SILENT 100 Manuel

SILENT

Instruction leaﬂet

Fig.1a

Fig.1b

Fig.4

Fig.3

Fig.2

L N

Fig.7

Fig.6

Fig.5

L N Ls

T (min) T (min)

SILENT T SILENT IT

SILENT PIR

Fig.10

Fig.9

Fig.8

L N Ls

2 3 41 5 6 7 8

OFF

Fig.11

L N Ls

SILENT 100

SILENT 125 & 150

ØF

MODEL A B C D E ØF

SILENT 100 158 158 109,3 84,6 79 98,9

SILENT 125 180 180 119 89 80 118

SILENT 150 214 214 149 113,5 95 147

SILENT

SILENT axial extractor fans

Please read this instruction booklet

carefully before installing or starting up

the product. It contains important

information on personal and user safety

measures to be followed whilst installing,

using and carrying out maintenance work

on the equipment.

The SILENT extractor fans have been

manufactured following current technical

safety regulations, production and quality

standards as laid down by the

international Quality Standard ISO 9001.

All components have been checked and

every one of the ﬁnal products will have

been individually tested at the end of the

manufacturing process.

Check that the product is in perfect

condition while unpacking. Make sure

that the product corresponds to the one

you have ordered and that the details on

the instruction plate fulﬁl your

requirements.

The installation and the disconnection

device of the ﬁxed installation used must

be in accordance with the installation

regulations in force in each country. Once

the product has been installed, pass this

booklet to the end user.

Recommendations

IMPORTANT: Before

installing and wiring the

unit, ensure that the

mains supply is

disconnected.

Working ambient

temperature for fan

equipment should not be

exceeded. Typically, this

falls within -5°C to +40°C,

unless stated otherwise.

The spigot cannot be

connected to a duct which

is used to extract smoke

from gas or any other fuel

appliance.

The extractor must not be

used in explosive or

corrosive atmospheres.

If the SILENT fan is

operating in a room

where there is a boiler or

any other kind of

combustion device that

requires airﬂow to work,

check that the air inlets to

the room are sufﬁcient.

This appliance can be

used by children aged

from 8 years and above

and persons with reduced

physical, sensory or

mental capabilities or lack

of experience and

knowledge if they have

been given supervision or

instruction concerning use

of the appliance in a safe

way and understand the

hazards involved. Children

shall not play with the

appliance. Cleaning and

user maintenance shall

not be made by children

without supervision.

Installation (fig.1):

This fan is IP45 rated and it is suitable

for application in zones 1 and 2 with

RCD protection.

1- Protection grille

2- Connection terminals

3- Outlet with backdraught shutter

4- Cable entry

5- Screwdriver to adjust Timer and

Hygrostat (not supply with S and P

models)

6- Pullcord (P models)

The SILENT is suitable for wall or ceiling

mounting and can either extract directly

to atmosphere or via a ducted system

(ﬁg.2).

The unit can be mounted on the wall or

ceiling using the 4 raw plugs and the

screws provided. Make a hole in the wall

or ceiling of diameter:

- SILENT-100: 105 to 107 mm.

- SILENT-125: 125 to 132 mm.

- SILENT-150: 160 to 158 mm.

If using the EnviroVent high rise wall kit,

please refer to kit for core drill size

If the unit is to be installed in a ducted

system, use the following standard

diameter of duct:

- SILENT-100: 100 mm.

- SILENT-125: 125 mm.

- SILENT-150: 150 or 160 mm.

Ensure that there are no obstructions to

the airﬂow and that the impeller turns

freely.

Fix the extractor fan to the wall in such a

way that it is not distorted in order to avoid

noise generation or problems with the

rotation of the impeller.

Make sure that the backdraught shutter

opens freely and has not being damaged

in transit. Introduce the mains cable

through the cable entry (4) and ﬁx it to the

wall.

Connect the electrical wiring as set out

below and then mount the protection

grille (1).

Electrical connection

The SILENT is an extractor fan designed

for a single-phase supply, with voltage

and frequency as indicated on the rating

plate of the unit.

The units are manufactured with double

electrical insulation (Class II) and

therefore they do not need an earth

connection.

The electrical cable must enter the

SILENT through the cable entry (4).

The SILENT must be connected to the

electrical supply in accordance with local

wiring regulations.

Once the cable has been introduced

proceed using the electrical wiring

diagram applicable to the selected

model.

SILENT S

For these models, use the following

diagrams:

Fig.3: Switching the extractor through the

light switch.

Fig.4: To switch the fan through an

independent switch.

SILENT T

This model is provided with an adjustable

over-run timer. The timer allows the fan to

continue to operate for the selected

period after the switch has been turned

oﬀ (ﬁ g.6).

Fig.5 shows how to connect the fan with

timer utilising the same switch as for the

lighting circuit.

To set the timer, turn the potentiometer

on the printed circuit board as (ﬁg. 7).

- To reduce the “run on” time, turn

anticlockwise (min. 1 minute).

- To increase the “run on” time, turn

clockwise (max: 30 minutes).

SILENT-100 IT

(This version is only available as

SILENT-100)

This model is provided with an adjustable

over-run timer. The timer allows the fan to

continue to operate for the selected

period after the switch has been turned

oﬀ (ﬁ g.6).

ATTENTION: The product also includes

an over-run timer facility that starts the

fan after the ﬁrst 50 seconds of non-

operation. After these ﬁrst 50 seconds,

the fan operates automatically.

SILENT HT

IMPORTANT: Do not remove the tape

covering the humidity sensor located

on the reserve of the grille.

Models provided with an electronic

humidistat which can be adjusted from

60% to 90 % RH (Relative Humidity) and

with a timer, adjustable between 1 and 30

minutes.

The desired humidity level and run on

time are selected by means of 8 dip-

switches placed on the printed circuit

board, and easily accessible. Each dip-

switch has two positions [ON (1) and OFF

(0)] which are selected with the small

plastic screwdriver supplied with the fan

(ﬁg.10):

The functions of these dip-switches are:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Envirovent Ventilateur

Envirovent

Envirovent fliterless infinity fan 230v Manuel utilisateur

Envirovent

Envirovent PIV AIR SOURCE Manuel utilisateur

Envirovent

Envirovent Slimline 150 Guide de démarrage rapide

Envirovent

Envirovent SLIMLINE 300 Guide de démarrage rapide

Envirovent

Envirovent ECO DMEV Manuel utilisateur

Envirovent

Envirovent ECO dMEV LC Manuel

Envirovent

Envirovent kudos Manuel

Envirovent

Envirovent ECO DMEV+ LC Manuel utilisateur

Envirovent

Envirovent energisava 380 Manuel utilisateur

Envirovent

Envirovent PIV Manuel utilisateur

Envirovent

Envirovent SELV Guide de démarrage rapide

Envirovent

Envirovent fliterless infinity fan 230v Guide de démarrage rapide

Envirovent

Envirovent ATMOS WALL Manuel utilisateur

Envirovent

Envirovent CYCLONE 7 230V Series Guide de démarrage rapide

Envirovent

Envirovent energiSava 250 Manuel utilisateur

Envirovent

Envirovent MEV SPIDER Manuel utilisateur

Envirovent

Envirovent OZEO Manuel utilisateur

Envirovent

Envirovent Silent-100 Design Manuel

Envirovent

Envirovent cyclone 7 Manuel utilisateur

Envirovent

Envirovent PROFILE-100 Instructions de montage

Envirovent

Envirovent Damp Pro DP-EVL Manuel utilisateur

Envirovent

Envirovent energisava250 Manuel utilisateur

Envirovent

Envirovent SABIK 350 Manuel utilisateur

Envirovent

Envirovent MEV 160 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage