Enovation Controls Murphy CONNECT Manuel utilisateur

00-02-1150

Section 40

2018-10-08

Murphy CONNECT

Installation Manual

Initial Release for U.S. Only

Section 40 2 00-02-1150

2018-10-08

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our

specifications and designs at any time. The latest version of this manual can be found at enovationcontrols.com.

BEFORE BEGINNING INSTALLATION OF THIS MURPHY

PRODUCT:

•Read and follow all installation instructions.

•Visually inspect this product before installation for

any damage during shipping.

•Disconnect all electrical power to the machine.

Failure to do this before welding can result in

damage to the panel and/or its components.

•It is your responsibility to have a qualified technician

install the unit and make sure the installation

conforms to local codes including but not limited to

double insulation and fire containment.

•Observe all Warnings and Cautions in each section

of these instructions.

•The Murphy CONNECT product is a telemetry

product designed for use in industrial environments

for remote monitoring and control when used with

Murphy’s PowerCore®family of controllers.

Contact Enovation Controls Technical Service if you have

any questions or concerns at: +1 918-317-4100.

IMPORTANT! Improper use and operation of electronic

products can be dangerous. It is required that point-of-

operation guarding devices be installed and maintained.

All such devices must meet OSHA and ANSI Machine

safety standards. The manufacturer shall not accept any

responsibility for installation, application or safety of

systems.

Section 40 3 00-02-1150

2018-10-08

Table of Contents

Operations Manual Location ............................................................................5

Hardware Installation.........................................................................................5

Inspecting Package Contents................................................................5

Installation.............................................................................................5

Preparation ....................................................................................... 5

Installing the Module......................................................................... 5

Dimensions for Installation...............................................................................6

Wiring Instructions ............................................................................................8

PIN Specifications for 8 Position Amphenol Connection .......................8

Accessories ..................................................................................................... 10

Specifications .................................................................................................. 10

Electrical..............................................................................................10

Environmental .....................................................................................10

Mechanical..........................................................................................10

Section 40 4 00-02-1150

2018-10-08

The CONNECT device can be used for remotely starting an engine when used in conjunction

with Murphy’s PowerCorecontrollers. Please be cognizant at all times of hands and other

objects that are in close proximity to the machine(s) being controlled as they may commence

operation suddenly and without warning.

Section 40 5 00-02-1150

2018-10-08

Operations Manual Location

After installation, please review the Murphy CONNECT Telematics Operations Manual prior to

placing the module into service. In order to access the Murphy CONNECT Telematics Manual

please visit Support.enovationcontrols.com,and then search for Murphy CONNECT

Telematics. The current manuals are listed under the Manuals section.

Hardware Installation

Inspecting Package Contents

Before attempting to install the product, it is recommended that you ensure all parts are

accounted for and inspect each item for damage (which sometimes occurs during shipping).

The items included in the box are:

Murphy CONNECT Telemetry Module – P/N 40-70-0525 includes:

•CONNECT Module

•Dual Antenna with GPS and Cellular, 3 meter (9.84ft) length

•Quick Start Guide

Installation

Preparation

Determine the location of where the CONNECT module will be installed. Ensure there is

proper room for the module to be mounted and the harnessing to be properly connected.

Ensure the supplied antenna is mounted in a location exterior to an enclosed area where

cellular and GPS signals are readily accessible to the antenna.

Dimensional drawings are not sized to print and appropriate measurement instruments should

be used when designing and mounting the Murphy CONNECT hardware.

Section 40 6 00-02-1150

2018-10-08

Dimensions for Installation

Murphy CONNECT Module

Inches

[mm]

Section 40 7 00-02-1150

2018-10-08

Dimensions for Installation

Antenna

Inches

[mm]

Section 40 8 00-02-1150

2018-10-08

Wiring Instructions

PIN Specifications for 8 Position Amphenol Connection

8 Pin

Battery (+)

CAN +

CAN -

RS485 +

RS485 -

Digital I/O

Ignition +

Battery -

Wiring of this device must meet all applicable electrical codes.

When the accessory harness is used, the PowerCore controller in the panel will need the I/O

established prior to use:

•TEC-10 and ML1000: Set the Digital Output 2 function to Ignition On

(On in Standby).

•ML2000: Set the Digital Output 4 function to Ignition On

(On in Standby).

NOTE: If the application is left in Auto mode, a battery maintaining system should

be installed for possible battery drain due to parasitic loads of ancillary devices

on the system.

Section 40 9 00-02-1150

2018-10-08

Troubleshooting

Murphy CONNECT has Wi-Fi communications which allows for minor troubleshooting of the

module. This section details the how to log on and interpret the data.

To access the Wi-Fi for troubleshooting ensure the device has the appropriate power to the

unit. When the unit is powered on the unit can be found by searching for a new Wi-Fi

connection on the PC or smart device.

Wi-Fi Address: CONNECT_xxxx (the xxxx represent the last 4 digits of the MAC address of the

device connecting)

Password: Murphy (use Murphy only when required to login)

Once connected to the device Wi-Fi network, open the browser and type in 192.168.6.1 into

the URL address to access the modem’s page (also shown on the CONNECT front label). The

page should resemble the image below and allow one to see the items listed below for

troubleshooting hardware and connectivity.

Application: States whether the application is running or not running. This should be running at

this stage

Version: Version of the CONNECT device

Connection: States whether the device is connected to a cellular network

Serial Number: Provides Serial Number of device. (Used to register device if device is

installed)

IMEI: Provides IMEI of device. (Used to register device if device is installed)

SIM: Provides SIM number.

Cell Signal: Provides range for cellular network. (0-6 = Poor, 7-15 = Okay, 15+ = Good)

GPS: States whether Locked or not locked for GPS positioning.

Satellites: 1-2 will not allow a lock for GPS, 3+ allow locking for GPS location.

Latitude: Once GPS is locked, provides Latitude coordinates for last known location.

Longitude: Once GPS is locked, provides Longitude coordinates for last known location.

Section 40 10 00-02-1150

2018-10-08

Accessories

Part #

Component

40000665

36” CONNECT Harness from PowerCore Panel to CONNECT Module

Specifications

Electrical

Operating Voltage: 9-36 VDC, protected against reverse battery polarity

Max Voltage: -40 to +60 VDC

Power Consumption:

12 VDC: Transmitting: 265 mA

Idle: 135 mA

Off: 0.5 mA (Using IGN to turn off)

On: ~ 175 mA Average

24 VDC: Transmitting: 135 mA

Idle: 90 mA

Off: 0.5 mA (Using IGN to turn off)

On: ~ 115 mA Average

Communications

1-CAN: J1939 (future use)

RS485: Modbus RTU

Wi-Fi: 2.4 GHz 802.11 b/g/n (Troubleshooting)

Cellular: (LTE)

GPS: (Location Services)

Connection: CONNECT Connector: Amphenol AT06-08S

Mating Connector: Amphenol AT04-08PA

Deutsch DT04-08PA

Inputs (1):

(1) Digital Inputs: Future Use (Shared with Digital Output)

Outputs (1):

(1) Digital Output: Future Use (Shared with Digital Input)

Environmental

Operating Temperature: -30°C to +80°C (-22°F to 176°F)

Storage Temperature: -30°C to +80°C (-22°F to 176°F)

Protection: IP67

Vibration: Random vibration, 8.17 Grms (5-2000 Hz), in 3 axes (Vibration spec was

met without the use of rubber isolation mounts)

Shock: 25g in 3 axes (shock specification was met without the use of rubber isolation

mounts)

Mechanical

Case Material: Polycarbonate 94V-2

Table des matières

Autres manuels Enovation Controls Instrument de mesure

Enovation Controls

Enovation Controls MURPHY PowerView PV380-R3 Manuel utilisateur

Enovation Controls

Enovation Controls Murphy PowerView PV380-R2 Manuel utilisateur

Enovation Controls

Enovation Controls MURPHY 20 Series Manuel utilisateur

Enovation Controls

Enovation Controls MURPHY HelmView HVS780 Manuel utilisateur

Enovation Controls

Enovation Controls PowerView PV480 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur