ENGINDOT HS60 Manuel utilisateur
User's Manual
Laser Distance Meter
HS60
Safety regulations
Please read the safety regulations and operation
guide carefully before operating.
Please read all of the operational guide and safety regulations
in this manual before operation . Improper operations
withoutcomplying with this manual guided could cause
or bodily injury to the user.
The instrument is not allowed to disassemble or repair
in any ways. lt is forbidden to do any illegal modification
or performance change for laser emitter. Please keep it
out of reach of children and avoid using by any irrelevant
personnel.
It is strictly prohibited to shoot eyes orother parts ofbody
with the laser; itisnot allowed take the laser to shoot any
objects' surface with strong reflecting.
Due to electromagnetic radiation interference to other
equipment and devices, please don't use the meter in the
plane or around medical equipment, don't use it in inflammable,
explosive environment.
Discarded batteries or meter device shall not processed
just like household garbage, please handle them in line
with related law and regulations.
Any quality issues or any questionson the meter, please
contact local distributors or manufacturer intime, we are
ready to offer solutions for you.
Professional casts quality and good
quality gets reputation
damage to the device, influence on measurement result
02
DISPLAY/KEYBOARD
Display
Keyboard
Turn on/Measuring
Addition
Reference Point/
Unit Switch
Save
Turn off/
Remove
Subtraction/
Sound
Area/Volume/
Pythagorean
Measuring
Power Supply
Record
Laser on
Maximum
Length,Area,
Volume and
Pythagorean
Minimum
Major Display
Auxiliary Display
03
Long press button , reset current
measurement unit, the default unit is: 0.000m
There are 6 units for selection
Batteries Installation
Battery Installation and Replacement
Discharge the battery door on the back of device,
and place battery according to correct polarity,
then cover the battery door.
Only 1.5 V AAA alkaline battery is applied to the
meter.
If not used for a long time, please take out the
battery to avoid battery corrosion to meter body.
Start the instrument/Menu Setting
Turn on/off the Instrument
Unit setting
Under off status, press button , device and
laser get starting simultaneously and stand by
for measurement.
Under on status, long press button for 3
seconds to turn the device off. The device can
also be shut off without any operation for 150
seconds.
04
Press key to change the reference point .
The device reference point by default is rear.
Changing Reference Point
Back Light On/Off
The back light is set to turn on and off automatically.
The back light can be on for 15s while operating,
and it will be shut off automatically in 15s when
there is no operation to the device.
Sound On/Off
Long press button to turn on or off the buzzer.
Length Area Volume
0.000m 0.000m20.000m3
0.00m 0.00m20.00m 3
0.0in 0.00ft 20.00ft3
0.00ft
0'00"1/16
0.00ft 20.00ft3
Units:
05
This function can keep the precision of the device.
Instruction: Power off, Long press button , and
then press . Release the button , then
"CAL" and a figure shows on the screen. User can
adjust the figure with button according to the
accuracy of the meter. Adjusting range: -9 to 9mm,
then, long press button to save the calibration
result.
Self-Calibration
Length Measurement & Calculation
Continuous Measuring:
Single Distance Measuring:
Turn on the laser beam by short press of the
button under measuring mode, press the
button again for single measurement of length,
then the measured results displayed in the major
display area.
Long press button under measuring mode
and enter into continuous measuring mode
Maximum measuring result displays in auxiliary
display area, present result displays in major
display area. Short press button or to exit
continuous measuring mode.
06
The resent measuring result of length is showed
in the auxiliary display area.Press , clear off
the result and measuring again if necessary.
Press again to exit the mode.
Press button , shows on the screen.
One of the side of rectangle blinking on the
display, please follow the below
instructions for area measuring:
Press once for length
Press again for width
The device calculates and shows the result in the
major display area.
Area Measurement:
The device calculates and shows the result in
the major display area.
Press , clear off the result and measuring
again if necessary.
Press again to exit the mode.
Press button twice to enter volume
measurement mode. A will shows on the top
of screen. Please follow the below instruction for
volume measuring:
Volume Measurement
Press for Length
Press again for Width
Press thirdly for height
07
Pythagoras
Press , measure the length of one leg (a)
Press , measure the length of another leg (b)
Device calculates the length of hypotenuse (x)
Short press four times, when one leg
of blinking,
Press , measure the length of hypotenuse (a)
Press , measure the length of one leg (b)
Device calculates the length of another leg (x)
Short press three times to enter Pythagoras
mode, the hypotenuse of blinking.
There are four Pythagoras modes in case that
user gets hard to reach the target.
1. Calculate the second leg by measuring the
hypotenuse and another leg.
2. Calculate the hypotenuse by measuring the
length of two legs.
08
4. Press six times till the hypotenuse of
blinking on the screen.
3. Press five times till the one side of
blinking on the screen.
The device can be used for length addition and
subtraction. Press to select the function once
get the length measuring result.
Short press , "+" shows in the major display
area, entering cumulation mode. Value of last
measurement and the result of cumulation will be
showed on the screen.
Short press , "-" shows in the major display
area, entering regressive mode. Value of last
measurement and the result of cumulation will be
showed on the screen.
Press , measure the length of one side (a)
Press , measure the length of the median line (b)
Press , measure the length of another side (c)
Device calculates the length of the leg in full line (x)
Press , measure the length of one hypotenuse (a)
Press , measure the length of another
hypotenuse (b)
Press , measure the length of one leg (c)
Device calculates the length of the leg in full line (x)
Legs must short than hypotenuse, or there will
be "err" shows on screen. In order to guarantee the
accuracy, please make sure all measurements are
start from the same point.
Addition / subtraction
Table des matières
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur