EnGenius ENH710EXT Manuel utilisateur
Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENH710EXT
Package content
Unpack the box and verify the content:
- ENH710EXT
- PoE injector
- Power adapter
- Quick Start Guide
- Wall mount screw set
- 2* Pole mounting strap
Minimum requirements
- Broadband Internet Service (cable or DSL modem)
- Internet browser (Internet Explorer, Safari, Firefox, Chrome)
Connecting the ENH710EXT
1. Remove the rear bottom panel.
2. Connect one end of the Ethernet cable into the LAN(PoE) port of the
ENH710EXT and the other end to the PoE Ethernet port on the PoE injector.
3. Connect the power adapter to the DC-IN port of the ENH710EXT and plug
the other end into an electrical outlet.
4. Connect the second Ethernet cable into the LAN port of the PoE injector and
the other end to the Ethernet port on the computer.
5. Place the panel removed from step 1 back into the device.
Note: The ENH710EXT should ONLY be powered via Ethernet cable connected
to the included PoE Injector.
Computer setup
1. After ensuring the EnGenius device is powered on and plugged in, ensure
that your computer is on.
2. For the next steps, refer to your operating system user manual.
3. Once your computer is on, ensure that your TCP/IP is set to ‘ON’ or
‘ENABLED’. In the control panel, double click network connections and then
double click on the connection of your Network Interface Card (NIC). Select
Internet Protocol (TCP/IP) and then click on the properties button.
4. If your PC is already on a computer network, ensure that you have set it to a
Static IP adress on the interface (or Ethernet card that will use the ENH710EXT)
as 192.168.1.21 and set the subnet mask address as 255.255.255.0.
Select ‘Use the following IP address’-radio button. Once the computer has been
prepared, proceed to setting up the ENH710EXT.
Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENH710EXT
ENH710EXT setup
1. To configure ENH710EXT, open a web browser (example: Microsoft Internet
Explorer, Mozilla Firefox, Google Chrome, etc.)
2. In the adress bar of the web browser, enter: 192.168.1.1 (the default IP
address of the ENH710EXT) and hit ENTER.
3. A login screen will appear. By default, the username of the ENH710EXT is
admin and the password is admin. Enter the current username and password
of the ENH710EXT and then click ‘Login’. Refer to the ENH710EXT user
manual on how to change the username and password.
4. After clicking ‘Login’ with the correct username an password,
the ENH710EXT main menu will appear. If you are successful, proceed to
setting up the wireless connection.
Switching between operating modes
This device can operate in the following modes: Access point, Client bridge,
WDS AP, WDS bridge and WDS station
A. Click on the operation mode link under the system navigation drop-down
menu.
B. Operating mode: Select an operating mode from the list (Access point, Client
bridge, WDS AP, WDS bridge or WDS station) and then click on the ‘Apply’
button.
C. All basic setup is completed. Note: The wireless connection is not secure. To
setup security on the ENH710EXT, refer to the ENH710EXT user manual.
Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENH710EXT
ENH710EXT wall mounting
A. Determine where the product is to be placed and mark the location on the
surface for the four mounting holes.
B. Use the appropiate drill bit to drill four 8 mm diagram and 37mm depth
holes in the markings and hammer the bolts into the openings.
C. Place the lock and flat washer on
the round head screws and drive the
screws to attach mounting base to the
back of the product.
D. Attach the device onto the wall by tightening the bolt’s flat washers and nuts
to secure the mounting base to the mounting surface.
Quick Installation Guide
EnGenius Europe | Veldzigt 28, 3454 PW De Meern,
Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us
https://www.linkedin.com/company/engeniuseurope
https://plus.google.com/+EngeniusEuropeBVDeMeern
https://www.youtube.com/user/engeniuseuropebv
https://twitter.com/engeniuseu
ENH710EXT
ENH710EXT pole mounting
A. Place the lock and flat washer on the cap screws and drive the screws to
attach the mounting base to the back of the product.
B. Determine which placement to be assemble. Drive the four round head
screws to attach the pole mount bracket to the mounting base.
C. Thread the open end of the pole strap through the two tabs on the pole
mount bracket.
D. Determine where the product is to be fastened. Lock and tighten pole strap to
secure pole mount bracket to the pole.
Autres manuels pour ENH710EXT
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels EnGenius Point d'accès sans fil
EnGenius
EnGenius EWS850AP Manuel utilisateur
EnGenius
EnGenius ECB300 Manuel utilisateur
EnGenius
EnGenius ECB600 Manuel utilisateur
EnGenius
EnGenius ETA1305 Manuel utilisateur
EnGenius
EnGenius EOC5611P Manuel utilisateur
EnGenius
EnGenius EAP300 Manuel utilisateur
EnGenius
EnGenius ENH200EXT Manuel utilisateur
EnGenius
EnGenius ECB300 Manuel utilisateur
EnGenius
EnGenius EnStationACv2 Manuel utilisateur
EnGenius
EnGenius ENH202 Manuel utilisateur
EnGenius
EnGenius EOC1650 Manuel utilisateur
EnGenius
EnGenius ENS202EXT Manuel utilisateur
EnGenius
EnGenius ENS200 Manuel utilisateur
EnGenius
EnGenius ENH200EXT Manuel utilisateur
EnGenius
EnGenius EAP900H Manuel utilisateur
EnGenius
EnGenius EnStation 6 Manuel utilisateur
EnGenius
EnGenius EOC1650 Manuel utilisateur
EnGenius
EnGenius ECB3500 Manuel utilisateur
EnGenius
EnGenius 11N Wireless Gigabit Multi-Function Client... Manuel utilisateur
EnGenius
EnGenius M2000 Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
