EnGenius ENH500 Manuel utilisateur

Version3.0

EnStation5-AC Kit

EnStationAC Kit

ENH500 Kit

Device*2

Screw Set*2

Pole Mounting

Strap*2

Bracket*2

Sealing nut*2

Dynamic Stick*2

PoE Adapter*2

Power Cord*2

EnStation5-AC

EnStationAC

1Connecting the Device

Remove the rear bottom panel.

Connect one end of the Ethernet cable into the LAN(PoE) port of the

device and the other end to the PoE Port on the PoE Adapter.

Connect the Power cord to the PoE Adapter and plug the other end

into an electrical outlet.

Connect the second Ethernet cable into the LAN port of the PoE

Adapter and the other end to the Ethernet Port into the computer.

Place the panel removed from step A back onto the device.

Note:

+ The device should ONLY be powered via Ethernet cable connected

to included PoE Adapter. EnStation5-AC/ENH500: Support proprietary

24V PoE input. EnStationAC: Support proprietary 54V PoE input

+ For EnStationAC : The 2nd Ethernet port of the device can supply

the 802.3af power source when used with the included PoE Adapter.

This kit is pre-conﬁgured in AP (Master, 192.168.1.1) and CB (Remote,

192.168.1.2) mode. Wireless connection will be built automatically once the

devices are powered up.

You must know : computer

)

IP Address Configuration

EnStationAC

To conﬁgure the device, open a web browser and enter IP

address as below.

3Device Setup

- IP: 192.168.1.1 If the last two

digits of the serial number

on the device label is -1.

- IP: 192.168.1.2 If the last two digits of the serial number

on the device label is -2.

B) A login screen will appear. By default, the username of the

device is admin and the password is admin. Enter the current

username and password of the device and then click Login.

Note: The model name on login screen depends on the product

you are using.

You can also use the EnWiFi App and

connect to the management SSID which

is on the device label and GUI to conﬁgure

the device. The default Wi-Fi password is

12345678.

Configure on GUI

4Switching Modes

A) The device can operate in the following modes.

EnJet enabled: Access Point, Client Bridge, WDS AP, WDS Station.

EnJet disabled: Access Point, Client Bridge, WDS AP, WDS Bridge,

WDS Station.

Note: The model name on login screen depends on the product

you are using.

EnStationAC

EnJet

EnStationAC

C) Use EnWiFi App, open conﬁgure →

Wireless to setup the Operation

Mode.

* It may take up to 90 seconds for device to initially power up.

Click on the Wireless link under the Network and setup the

Operation Mode.

Configure on EnWiFi App

ENH500

PoE Adapter*2

Device *2

Pole Mounting *2 Wall Mount

Screw Set *2

Waterproof *2

Power Cord*2

[email protected]

Local: (+971) 4 339 1227

North America

Technical Support

Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary

depending on many factors including environmental conditions, distance between devices,

radio interference in the operating environment, and mix of devices in the network. Features

and specications subject to change without notice. Trademarks and registered trademarks

Notes

ENH500

Thread the open end of the Pole Strap through the two tabs on

the Pole Mount Bracket.

Lock and tighten Pole Strap to secure Pole Mount Bracket to the

pole.

Pole Mounting

Plug the dynamic stick into the bracket.

Screw the sealing nut and assembled parts, tighten it

with 80kgf.cm.

Put the nock washer on the dynamic stick.

Assemble the mounting parts to the device.

E) Thread the open end of the pole strap through the two tabs on

the bracket.

Lock and tighten pole strap to secure bracket to the pole.

EnStation5-AC / EnStationAC

Determine the mounting location. Mark and drill two pilot

holes aligning to the screw holes of the bracket.

Put wall anchors into the holes and insert screw into the

wall anchor.

Screw and secure the bracket in place.

ENH500

Determone where the Access Point to placed and stick the

Adhesive label on the surface.

Use the appropriate drill bit drill teo 8.1 mm diagram and 26 mm

depth holes on the markings of the label.

Remove the label and Screw the anchors unto the holes until

they are ﬂush with the wall.

Screw the includes screws into the anchors. place the Access

Point against wall with the mounting screw heads.

5Mounting the Device

Wall Mounting

Plug the dynamic stick into the bracket.

Screw the sealing nut and assembled parts, tighten it with

80kgf.cm.

Put the nock washer on the dynamic stick.

Assemble the mounting parts to the device.

EnStation5-AC / EnStationAC

Autres manuels pour ENH500

Ce manuel convient aux modèles suivants

Autres manuels EnGenius Point d'accès sans fil

EnGenius

EnGenius EOC-3610s-EXT Manuel utilisateur

EnGenius

EnGenius ENS202v2 Manuel utilisateur

EnGenius

EnGenius EOC2611P Manuel utilisateur

EnGenius

EnGenius EAP300 Manuel utilisateur

EnGenius

EnGenius ETR9360 Manuel utilisateur

EnGenius

EnGenius ENS200 Manuel utilisateur

EnGenius

EnGenius ENS500EXT Manuel utilisateur

EnGenius

EnGenius EAP300 Manuel utilisateur

EnGenius

EnGenius EWS377AP Manuel utilisateur

EnGenius

EnGenius ENS202EXT Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

EnGenius

EnGenius EOC-2610 Manuel utilisateur

EnGenius

EnGenius EWS850-FIT Manuel utilisateur

EnGenius

EnGenius ECB1221R Manuel utilisateur

EnGenius

EnGenius EOA7530 Manuel utilisateur

EnGenius

EnGenius ENH210EXT Manuel utilisateur

EnGenius

EnGenius EOC1650 Manuel utilisateur

EnGenius

EnGenius Wireless Outdoor Access Point & Client... Manuel utilisateur

EnGenius

EnGenius ECB300 Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

EnGenius

EnGenius EOA7530 Manuel utilisateur

EnGenius

EnGenius EnStation5-ACv2 Manuel utilisateur

EnGenius

EnGenius ECB150 Manuel utilisateur

EnGenius

EnGenius ECB1200 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur