Eneo HDC-2080CS Manuel utilisateur
EN
User Manual
1/3” HDcctv Camera, WDR,
Day&Night, 1920x1080, C/CS,
12/24V
HDC-2080CS D
Safety Precaution
03
FULL-HD MEGA-PIXEL CAMERA
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
FULL-HD MEGA-PIXEL CAMERA
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
04
FULL-HD MEGA-PIXEL CAMERA
Contents
Safety Precaution
p.03~04
Contents
p.05
Features
p.06~07
Composition
p.07
Dimensions
p.07
Part Names
p.08
Installation Instructions
p.09~10
Operating Instructions
p.11~26
Specifications
p.27~28
05
FULL-HD MEGA-PIXEL CAMERA
Features
Key Features
06
• Full HD, 2Mega Pixel EX-SDI CAMERA, 1920x1080(30p/25p)
• Extended long reach HD Solution
• Real time True WDR(Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• CS mount supported (Option: C-mount adaptor)
• Dual Filter Switcher
• Day & Night Simulation for easy focus adjustment
• Various Zooming Technologies
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
- Flex Zoom
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
• Motion Detection, Privacy Mask, Defog, Sens-up(~x32), D-WDR,
H/V/HV Flip, D-Zoom(~8x), Lens Shade Compensation, BLC/HLC,
Pixel Defect Compensation, Title Set
• EX-SDI or HD-SDI switchable
• Top performance at low light sensitivity (Sens-up On)
• OSD menu & CVBS Video output BNC for easy installation & maintenance.
• Circuit protection against faulty connection in power polarity
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-D/P)
•Fine Back focus adjustment
FULL-HD MEGA-PIXEL CAMERA
(unit : mm)
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With Intelligent Focus Indicator and FOCUS ASSIST menu,
- Offers easy adjustment of Focus
- Eliminates the mistake of the erratic focus adjustment
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
07
Composition
Features
Dimensions
Box Camera
Torque Wrench:
3mm (1pc)
Dust Protection
Cap (1pc)
Operating
Instruction
72
74 82
89
Ø35
FULL-HD MEGA-PIXEL CAMERA
Part Names
08
④
①OSD Control Joy stick
②Power input terminal
(AC24V/DC12V or DC12V)
③RS-485 / IR connector
④
HD-SDI/EX-SDI
output connector
⑤Power LED
⑥CVBS output connector
⑦Video format Switch
③
①
⑤
⑦
⑥
②
Torque
Wrench
Dust
Protection Cap
No.
1
2
3
4
DC Iris
Damp(-)
Damp(+)
Drive(+)
GND
Front Case
Rear Case
Back focus
adjustment
Mount Holes
(Top / Bottom)
SIDE VIEW
Lens Connector
for Auto Iris lenses
PIN 1PIN 3
PIN 2PIN 4
REAR VIEW
Installation Instructions
FULL-HD MEGA-PIXEL CAMERA
09
1. Remove the dust protection cap from the lens mount.
2. Screw the lens onto the camera firmly.
3. Plug the lens plug into the lens connector on the rear of camera case.
4. Mount the camera to the wall or ceilling with a corresponding mounting bracket
through the camera mount holes (1/4” thread insert) on its top or bottom.
CAUTION
Installation and commissioning Instructions
• Make sure the power is removed before the installation.
• Follow the order for applying power.
First connect the low voltage (DC12V or AC24V), then plug the AC adapter
to AC outlets to avoid an improper reset from power jitter and a damage from
the surge voltage when no load.
• Care should be taken the cable is NOT to be damaged, kinked or exposed in
the hazardous area.
• Do not expose the camera directly to a strong light source such as the sun or
spot light.
Setting the back focus adjustment
The proper back focus adjustment is essential for the motorized zoom lens to
get the all time sharp focus when zooming in and out by the remote control.
For easier and better adjustment, this camera provides FOCUS ASSIST menu
which prevents from the mistake of the focus adjustment.
With enabling FOCUS ASSIST menu, follow the procedure to get the best back
focus adjustment.
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).
2. Shoot the object departing from about 10Meters.
3. Adjust ’Back focus adjustment with Torque wrench’ until the optimum focus
is achieved.
4. Set the lens for zoom position to TELE and adjust the lens focus for best focus.
5. Set the lens for zoom position to WIDE again, check if the focus adjustment
was the best. If not, re-adjust ‘Back focus adjustment’ slightly.
Start up
When the camera is powered properly, it starts up with initializing the internal
parameters.
Installation Instructions
FULL-HD MEGA-PIXEL CAMERA
10
Power Supply Connections
Make sure the power is removed before the installation.
Camera can work with either 24AC or 12VDC, dual voltage power .
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems
In case that HD-SDI/EX-SDI Inputs are not supported in Monitor, please use
HD-SDI/EX-SDI Converter to connect HD-SDI/EX-SDI cable with Monitor
Some computer monitors or TVs may not support 30p/25p.
In this case, HD-SDI/EX-SDI DVR which can convert the frame rate to 60p/50p
is highly recommended.
Please check Specification of Monitor before installation.
Set the video format according to system,
EX-SDI or HD-SDI
DVR
350M+ via RG59u or 5C2V cable
350M+ via
RG59u or 5C2V
cable
350M+ via RG59u or 5C2V cable
1M~120M via RG59u or 5C2V cable
1M~120M
via
RG59u or
5C2V cable
1M~120M
via
RG59u or
5C2V cable
1M~120M
via
RG59u or
5C2V cable
DVR
(HD-SDI)
Camera
(HD-SDI)
Camera
(HD-SDI)
Camera
Camera
HDA-3000E HDA-3000E
HDA-3000E
DVR
(HD-SDI)
DVR
(HD-SDI)
Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
11
Using OSD Controller
Setup menu can be accessed and controlled by OSD control joy stick on the rear
of the camera unit.
Five commands are available with the joy stick.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left
or right.
4) denotes the long press down straightly for about 2 seconds
Description of D-ZOOM* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
(*) Works only when OSD Menu is inactive.
Autres manuels pour HDC-2080CS
2
Table des matières
Autres manuels Eneo Caméra IP
Eneo
Eneo MPC-52A0030P0A Manuel utilisateur
Eneo
Eneo HDC-2080Z03 Manuel utilisateur
Eneo
Eneo MCB-64A0003M0A Manuel utilisateur
Eneo
Eneo HDC-2100M1080 Manuel utilisateur
Eneo
Eneo HDD-1080M2810IR D Manuel utilisateur
Eneo
Eneo Minitrax HDD-1012PTZ1080 Instructions d'installation
Eneo
Eneo MEB-64V2812M0A Manuel utilisateur
Eneo
Eneo VKC-1416C Manuel utilisateur
Eneo
Eneo TVB-920F36IR Manuel utilisateur
Eneo
Eneo NXC-1602M Manuel utilisateur
Eneo
Eneo 22X Manuel utilisateur
Eneo
Eneo MCB-72M2712M0A Manuel utilisateur
Eneo
Eneo PXC-2080Z03 Manuel utilisateur
Eneo
Eneo TVB-2080V2812IR Manuel utilisateur
Eneo
Eneo MSM-42F0037MPA Manuel utilisateur
Eneo
Eneo HDD-2080Z03IR D Manuel utilisateur
Eneo
Eneo VKC-1374/IR Manuel utilisateur
Eneo
Eneo MPC-54A0003M0A Manuel utilisateur
Eneo
Eneo HDC-2080CS Manuel utilisateur
Eneo
Eneo GXC-1605M Manuel utilisateur
