Endress+Hauser Smartec CLD18 Manuel utilisateur
Products Solutions Services
Operating Instructions
Smartec CLD18
Conductivity measuring system
BA01149C/07/EN/06.17
71393688
AUTHORIZED DISTRIBUTOR:
InstrumentsAndControl.com
Houston, Texas USA
281-609-7170
Smartec CLD18 Table of contents
Endress+Hauser 3
Table of contents
1 Document information ......... 4
1.1 Warnings ........................... 4
1.2 Symbols used ........................ 4
1.3 Symbols on device .................... 5
2 Basic safety instructions ....... 5
2.1 Requirements for the personnel ........ 5
2.2 Designated use ...................... 5
2.3 Occupational safety .................. 5
2.4 Operational safety ................... 7
2.5 Product safety ....................... 7
2.6 IT security .......................... 7
3 Product description ............. 8
3.1 Product design ....................... 8
4 Incoming acceptance and
product identification .......... 9
4.1 Incoming acceptance ................. 9
4.2 Product identification ................. 9
4.3 Scope of delivery .................... 10
4.4 Certificates and approvals ............ 11
5 Installation .................... 11
5.1 Installation conditions ............... 11
5.2 Mounting the compact device ......... 17
5.3 Post-installation check ............... 17
6 Electrical connection .......... 17
6.1 Connecting the transmitter ........... 17
6.2 Ensuring the degree of protection ..... 21
6.3 Post-connection check ............... 21
7 Operation options ............. 22
7.1 Overview of operating options ........ 23
7.2 Structure and function of the operating
menu ............................. 24
8 Commissioning ................ 25
8.1 Switching on the measuring device .... 25
8.2 Display settings (Display menu) ....... 25
8.3 Configuring the measuring device ..... 26
8.4 Advanced settings .................. 26
8.5 Calibration (Calibration menu) ........ 31
9 Diagnostics and
troubleshooting ............... 34
9.1 General troubleshooting ............. 34
9.2 Trouble shooting instructions ......... 34
9.3 Pending diagnostic messages ......... 35
10 Maintenance .................. 38
10.1 Maintenance tasks .................. 38
11 Repairs ......................... 39
11.1 General notes ...................... 39
11.2 Return ............................ 39
11.3 Disposal ........................... 39
12 Accessories .................... 40
12.1 Calibration solutions ................ 40
13 Technical data ................. 40
Index ................................. 47
Document information Smartec CLD18
4 Endress+Hauser
1 Document information
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of non-
compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of non-
compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to property.
1.2 Symbols used
Symbol Meaning
Additional information, tips
Permitted or recommended
Not permitted or not recommended
Reference to device documentation
Reference to page
Reference to graphic
Result of a step
Smartec CLD18 Basic safety instructions
Endress+Hauser 5
1.3 Symbols on device
Symbol Meaning
Reference to device documentation
2 Basic safety instructions
2.1 Requirements for the personnel
• Installation, commissioning, operation and maintenance of the measuring system may be
carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the specified
activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions and
must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Designated use
The compact measuring system is used for inductive conductivity measurement in liquids with
medium to high conductivity.
Use of the device for any purpose other than that described, poses a threat to the safety of
people and of the entire measuring system and is therefore not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.
NOTICE
Applications outside specifications!
Incorrect measurements, malfunctions and even measuring point failure could result
‣Use the product only in accordance with the specifications.
‣Pay attention to the technical data on the nameplate.
2.3 Occupational safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
Basic safety instructions Smartec CLD18
6 Endress+Hauser
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable European standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.
Smartec CLD18 Basic safety instructions
Endress+Hauser 7
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
2.5 Product safety
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
European standards have been observed.
2.6 IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.
Product description Smartec CLD18
8 Endress+Hauser
3 Product description
3.1 Product design
1
2
3
4
5
6
7
A0019184
1 Elements
1 Temperature sensor
2 Process connection
3 Leakage bore (offset by 90° in relation to the flow direction)
4 Removable housing cover
5 Window for display
6 Cable glands (M12)
7 Flow opening of sensor
Smartec CLD18 Incoming acceptance and product identification
Endress+Hauser 9
4 Incoming acceptance and product identification
4.1 Incoming acceptance
1. Verify that the packaging is undamaged.
Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
Technical data→ 40
4.2 Product identification
4.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Order code
• Extended order code
• Serial number
• Firmware version
• Ambient and process conditions
• Input and output values
• Measuring range
• Safety information and warnings
• Protection class
‣Compare the information on the nameplate with the order.
Incoming acceptance and product identification Smartec CLD18
10 Endress+Hauser
4.2.2 Product identification
Product page
www.endress.com/CLD18
Interpreting the order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers
Obtaining information on the product
1. Open the product website.
2. At the top of the page, select the link Services.
An additional sidebar opens up.
3. Select Online Tools followed by Access device specific information.
An additional window opens.
4. Enter the order code from the nameplate into the search field. Then select Show
details.
Details of each feature (selected option) of the order code are displayed.
Manufacturer's address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
4.3 Scope of delivery
The delivery comprises:
• A Smartec CLD18 measuring system in the version ordered
• Operating Instructions BA01149C/07/EN
Autres manuels pour Smartec CLD18
1
Table des matières
Autres manuels Endress+Hauser Instrument de mesure
Endress+Hauser
Endress+Hauser silopilot FMM 460 Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquicap M FMI52 PFM Manuel utilisateur
Endress+Hauser
Endress+Hauser Proline Promass E 200 Manuel
Endress+Hauser
Endress+Hauser Proserve NMS80 Instructions d'utilisation
Endress+Hauser
Endress+Hauser Liquiline Control CDC90 Manuel utilisateur
Endress+Hauser
Endress+Hauser Levelflex FMP55 Manuel utilisateur
Endress+Hauser
Endress+Hauser Stamosens CSM750 Manuel utilisateur
Endress+Hauser
Endress+Hauser LT5 Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquicap M FMI52 Caractéristiques techniques
Endress+Hauser
Endress+Hauser Teqwave F Manuel utilisateur
Endress+Hauser
Endress+Hauser Levelflex FMP50 Caractéristiques techniques
Endress+Hauser
Endress+Hauser Gammapilot M FMG60 Caractéristiques techniques
Endress+Hauser
Endress+Hauser Levelflex FMP56 Manuel
Endress+Hauser
Endress+Hauser Smartec S CLD134 Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquiline System CA80TP Caractéristiques techniques
Endress+Hauser
Endress+Hauser FOUNDATION Proline 500 digital Caractéristiques techniques
Endress+Hauser
Endress+Hauser Prothermo NMT81 Manuel utilisateur
Endress+Hauser
Endress+Hauser Stamolys CA71SI Series Manuel utilisateur
Endress+Hauser
Endress+Hauser Liquiphant S FDL60 Instructions d'utilisation
Endress+Hauser
Endress+Hauser Proline Promass F 200 HART Manuel utilisateur
