Endress+Hauser Proline Prosonic Flow B 200 Manuel utilisateur

Brief Operating Instructions

Proline Prosonic Flow B 200

Ultrasonic flow measuring system

These Instructions are Brief Operating Instructions; they do not replace the

Operating Instructions included in the scope of supply.

For detailed information, refer to the Operating Instructions and other

documentation on the CD-ROM provided or visit "www.endress.com/

deviceviewer".

KA01096D/06/EN/01.11

71147011

Table of contents Proline Prosonic Flow B 200

2 Endress+Hauser

Table of contents

1 Document conventions ...................................... 3

1.1 Document conventions ........................................... 3

2 Basic safety instructions ...................................... 5

2.1 Requirements for the personnel ....................................... 5

2.2 Designated use ............................................... 5

2.3 Workplace safety .............................................. 6

2.4 Operational safety .............................................. 6

2.5 Product safety ................................................ 6

3 Product description ......................................... 7

3.1 Product design ............................................... 7

4 Incoming acceptance and product identification ..................... 8

4.1 Incoming acceptance ............................................ 8

4.2 Product identification ............................................ 9

5 Storage and transport ...................................... 10

5.1 Storage conditions ............................................. 10

5.2 Transporting the product .......................................... 10

6 Mounting ............................................... 12

6.1 Mounting requirements .......................................... 12

6.2 Mounting the measuring device ...................................... 16

6.3 Post-mounting check ............................................ 17

7 Electrical connection ....................................... 19

7.1 Connection conditions ........................................... 19

7.2 Connecting the measuring device ...................................... 20

7.3 Special connection instructions ....................................... 22

7.4 Ensuring the degree of protection ...................................... 22

7.5 Post-connection check ........................................... 22

8 options ................................................ 23

8.1 Structure and function of the operating menu ................................ 23

8.2 Access to the operating menu via the local display .............................. 24

8.3 Access to the operating menu via the operating tool ............................. 30

9 Commissioning ........................................... 31

9.1 Function check .............................................. 31

9.2 Switching on the measuring device ..................................... 31

9.3 Setting the operating language ....................................... 31

9.4 Configuring the measuring device ..................................... 32

9.5 Defining the tag name ........................................... 32

9.6 Protecting settings from unauthorized access ................................ 33

10 Diagnostic information ...................................... 34

Proline Prosonic Flow B 200 Document conventions

Endress+Hauser 3

1 Document conventions

1.1 Document conventions

1.1.1 Safety symbols

Symbol Meaning

DANGER

A0011189-EN

DANGER!

This symbol alerts you to a dangerous situation. Failure to avoid this situation will

result in serious or fatal injury.

WARNING

A0011190-EN

WARNING!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in serious or fatal injury.

CAUTION

A0011191-EN

CAUTION!

This symbol alerts you to a dangerous situation. Failure to avoid this situation can

result in minor or medium injury.

NOTICE

A0011192-EN

NOTICE!

This symbol contains information on procedures and other facts which do not result

in personal injury.

1.1.2 Electrical symbols

Symbol Meaning

A0011197

Direct current

A terminal to which DC voltage is applied or through which direct current flows.

A0011198

Alternating current

A terminal to which alternating voltage (sine-wave) is applied or through which alternating current flows.

)

A0011200

Ground connection

A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.

A0011199

Protective ground connection

A terminal which must be connected to ground prior to establishing any other connections.

A0011201

Equipotential connection

A connection that has to be connected to the plant grounding system: This may be a potential equalization

line or a star grounding system depending on national or company codes of practice.

1.1.3 Tool symbols

A0011219 A0011220 A0011221 A0011222

Phillips head screwdriver Flat blade screwdriver Allen key Hexagon wrench

Document conventions Proline Prosonic Flow B 200

4 Endress+Hauser

1.1.4 Symbols for certain types of information

Symbol Meaning

A0011182

Allowed

Indicates procedures, processes or actions that are allowed.

A0011183

Preferred

Indicates procedures, processes or actions that are preferred.

A0011184

Forbidden

Indicates procedures, processes or actions that are forbidden.

A0011193

Tip

Indicates additional information.

A0011194

Reference to documentation

Refers to the corresponding device documentation.

A0011195

Reference to page

Refers to the corresponding page number.

A0011196

Reference to graphic

Refers to the corresponding graphic number and page number.

,…

Series of steps

ÃResult of a sequence of actions

1.1.5 Symbols in graphics

Symbol Meaning

1, 2, 3,... Item numbers

,…

Series of steps

A, B, C, ... Views

A-A, B-B, C-C, ... Sections

A0013441

Flow direction

A0011187

Hazardous area

Indicates a hazardous area.

A0011188

Safe area (non-hazardous area)

Indicates a non-hazardous area.

Proline Prosonic Flow B 200 Basic safety instructions

Endress+Hauser 5

2 Basic safety instructions

2.1 Requirements for the personnel

The personnel must fulfill the following requirements for its tasks:

►Trained, qualified specialists must have a relevant qualification for this specific function and

task

►Are authorized by the plant owner/operator

►Are familiar with federal/national regulations

►Before beginning work, the specialist staff must have read and understood the instructions in

the Operating Instructions and supplementary documentation as well as in the certificates

(depending on the application)

►Following instructions and basic conditions

2.2 Designated use

Application and media

The measuring device described in these Instructions is intended only for flow measurement of

gases.

Depending on the version ordered, the measuring device can also measure potentially explosive,

flammable, poisonous and oxidizing media.

To ensure that the measuring device remains in proper condition for the operation time:

►Only use the measuring device in full compliance with the data on the nameplate and the

general conditions listed in the Operating Instructions and supplementary documentation.

►Based on the nameplate, check whether the ordered device is permitted for the intended use

in the hazardous area (e.g. explosion protection, pressure vessel safety).

►Use the measuring device only for media against which the process-wetted materials are

adequately resistant.

Incorrect use

The manufacturer is not liable for damage caused by improper or non-designated use.

NOTICE

Danger of breakage of the sensor due to corrosive or abrasive fluids!

►Verify the compatibility of the process fluid with the sensor material.

►Ensure the resistance of all fluid-wetted materials in the process.

►Observe the specified maximum process pressure.

Residual risks

External surface temperature of the transmitter can increase by 20 K due to power consumption

of internal electronical components. Hot process fluids passing through the measuring device

will further increase the surface temperature of the measuring device. Especially the surface of

the sensor can reach temperatures which are close to process temperature.

Possible burn hazard due to fluid temperatures!

►For elevated fluid temperature, ensure protection against contact to prevent burns.

Basic safety instructions Proline Prosonic Flow B 200

6 Endress+Hauser

2.3 Workplace safety

For work on and with the device:

►Wear the required personal protective equipment according to federal/national regulations.

For welding work on the piping:

►Do not ground the welding unit via the measuring device.

2.4 Operational safety

Risk of injury.

►Operate the device in proper technical condition and fail-safe condition only.

►The operator is responsible for interference-free operation of the device.

2.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the-art safety requirements, has been tested, and left the factory in a condition in which they

are safe to operate.

It fulfills general safety requirements and legal requirements. It also conforms to the EC directives

listed in the device-specific EC declaration of conformity. Endress+Hauser confirms this fact by

applying the CE mark.

Proline Prosonic Flow B 200 Product description

Endress+Hauser 7

3 Product description

3.1 Product design

A0016199

å 1 Important components of a measuring device

1 Electronics compartment cover

2 Display module

3 Main electronics module

4 Cable glands

5 Transmitter

6 I/O electronics module

7 Terminals (spring loaded terminals, pluggable)

8 Connection compartment cover

9 Sensor

10 Transducer

Incoming acceptance and product identification Proline Prosonic Flow B 200

8 Endress+Hauser

4 Incoming acceptance and product identification

4.1 Incoming acceptance

A0015502

A0013843

A0013695

A0015502

A0013698

A0015502

DELIVERY NOTE

A0013699

Proline Prosonic Flow B 200 Incoming acceptance and product identification

Endress+Hauser 9

A0015502

A0013697

If one of the conditions does not comply, contact your Endress+Hauser distributor.

4.2 Product identification

The following options are available for identification of the measuring device:

• Nameplate specifications

• Order code with breakdown of the device features on the delivery note

•Enter serial numbers from nameplates in W@M Device Viewer

(www.endress.com/deviceviewer): All information about the measuring device is displayed.

For an overview of the scope of the Technical Documentation provided, refer to the following:

The W@M Device Viewer : Enter the serial number from the nameplate

(www.endress.com/deviceviewer)

Order code:

Ext. ord. cd.:

Ser. no.:

A0014053

å 2 Example of a nameplate

1 Order code

2 Serial number (Ser. no.)

3 Extended order code (Ext. ord. cd.)

For detailed information about interpreting the nameplate specifications, refer to the

Operating Instructions for the device on the CD-ROM provided

Storage and transport Proline Prosonic Flow B 200

10 Endress+Hauser

5 Storage and transport

5.1 Storage conditions

Observe the following notes for storage:

• Store in original packaging.

• Do not remove protective covers or protective caps installed on process connections.

• Protect from direct sunlight.

•Storage temperature: –40 to +80 °C (–40 to +176 °F)

• Store in a dry and dust-free place.

• Do not store outdoors.

5.2 Transporting the product

!WARNING

Center of gravity of the measuring device is higher than the suspension points of the

webbing slings.

Risk of injury if the measuring device slips.

►Secure the measuring device from rotating or slipping.

►Observe the weight specified on the packaging (stick-on label).

►Observe the transport instructions on the stick-on label on the electronics compartment cover.

A0015606

Observe the following notes during transport:

•Transport the measuring device to the measuring point in the original packaging.

• Do not remove protective covers or protective caps installed on process connections. They

prevent mechanical damage to the sealing surfaces and fouling in the measuring tube.

Autres manuels pour Proline Prosonic Flow B 200

Table des matières

Autres manuels Endress+Hauser Instrument de mesure

Endress+Hauser

Endress+Hauser Proline Promass X 500 FOUNDATION Fieldbus Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Prowirl 73 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Dosimag Manuel utilisateur

Endress+Hauser

Endress+Hauser Promass 40 Manuel utilisateur

Endress+Hauser

Endress+Hauser Fieldgate FXA520 Manuel utilisateur

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline Promag L 400 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Tankvision Gauge Link NXA20 Manuel utilisateur

Endress+Hauser

Endress+Hauser iTEMP TMT162 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline 500 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Deltabar S PMD75 Manuel

Endress+Hauser

Endress+Hauser silopilot FMM 460 Manuel utilisateur

Endress+Hauser

Endress+Hauser EngyCal RH33 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline Prosonic Flow B 200 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Analytik Jena multi N/C 2100S Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex M FMP43 Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic M FMU44 Manuel utilisateur

Endress+Hauser

Endress+Hauser PROline promag 53 Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic M FMU41 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline t-mass 65 Manuel utilisateur

Endress+Hauser

Endress+Hauser Promag 300 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promass S 300 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Prosonic Flow90U Manuel

Endress+Hauser

Endress+Hauser UniFit CPA 441 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Acterna

Acterna MS1400 Manuel utilisateur

R&S

R&S ZPH Manuel utilisateur