Endress+Hauser Deltapilot M FMB50 Caractéristiques techniques

Products Solutions Services

Brief Operating Instructions

Deltapilot M FMB50, FMB51,

FMB52, FMB53

Hydrostatic level measurement

PROFIBUS PA

Pressure sensor with the CONTITE™ measuring cell

(condensate-resistant)

These Brief Operating Instructions are not a substitute for the

Operating Instructions pertaining to the device.

Detailed information about the device can be found in the

Operating Instructions and the additional documentation.

Available for all device versions via

• Internet: www.endress.com/deviceviewer

• Smartphone/tablet: Endress+Hauser Operations app

KA01034P/00/EN/06.21-00

71549534

2021-09-30

Associated documentation Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA

2 Endress+Hauser

1 Associated documentation

Order code:

Ext. ord. cd.:

Ser. no.:

www.endress.com/deviceviewer Endress+Hauser

Operations App

XXXXXXXXXXXX

XXXXX-XXXXXX

XXX.XXXX.XX

Serial number

A0023555

2 About this document

2.1 Document function

The Brief Operating Instructions contain all the essential information from incoming

acceptance to initial commissioning.

Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA About this document

Endress+Hauser 3

2.2 Symbols used

2.2.1 Safety symbols

DANGER

This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in

serious or fatal injury.

WARNING

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

serious or fatal injury.

CAUTION

This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in

minor or medium injury.

NOTICE

This symbol contains information on procedures and other facts which do not result in

personal injury.

2.2.2 Electrical symbols

Protective earth (PE)

Ground terminals that must be connected to ground prior to establishing any other

connections.

The ground terminals are located on the interior and exterior of the device:

• Interior ground terminal: protective earth is connected to the mains supply.

• Exterior ground terminal: device is connected to the plant grounding system.

2.2.3 Symbols for certain types of information and graphics

Symbols for certain types of information and graphics

Permitted

Procedures, processes or actions that are permitted

Forbidden

Procedures, processes or actions that are forbidden

Tip

Indicates additional information

Reference to documentation

Reference to page

Visual inspection

Notice or individual step to be observed

Basic safety instructions Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA

4 Endress+Hauser

1, 2, 3, ...

Item numbers

Series of steps

Result of a step

2.3 Registered trademarks

• KALREZ®

Registered label of E.I. Du Pont de Nemours & Co., Wilmington, USA

• TRI-CLAMP®

Registered label of Ladish & Co., Inc., Kenosha, USA

• PROFIBUS PA®

Trademark of the PROFIBUS User Organization, Karlsruhe, Germany

• GORE-TEX® trademark of W.L. Gore & Associates, Inc., USA

3 Basic safety instructions

3.1 Requirements for the personnel

Personnel must meet the following requirements for their tasks:

‣Trained, qualified specialists must be suitably qualified to perform this function and task

‣Are authorized by the plant owner/operator

‣Are familiar with federal/national regulations

‣They must have read and understood the instructions in the manual, supplementary

documentation and certificates (depending on the application) prior to starting work

‣They must follow instructions and comply with basic conditions

3.2 Intended use

The Deltapilot M is a hydrostatic pressure sensor for measuring level and pressure.

3.2.1 Foreseeable incorrect use

The manufacturer is not liable for damage caused by improper or non-intended use.

Verification for borderline cases:

‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in

verifying the corrosion resistance of fluid-wetted materials, but does not accept any

warranty or liability.

3.3 Workplace safety

For work on and with the device:

‣Wear the required personal protective equipment according to federal/national

regulations.

Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA Basic safety instructions

Endress+Hauser 5

‣Switch off the supply voltage before connecting the device.

3.4 Operational safety

Risk of injury!

‣Operate the device in proper technical condition and fail-safe condition only.

‣The operator is responsible for interference-free operation of the device.

Conversions to the device

Unauthorized modifications to the device are not permitted and can lead to unforeseeable

dangers:

‣If, despite this, modifications are required, consult with Endress+Hauser.

Repair

To ensure continued operational safety and reliability:

‣Carry out repairs on the device only if they are expressly permitted.

‣Observe federal/national regulations pertaining to repair of an electrical device.

‣Use original spare parts and accessories from Endress+Hauser only.

Hazardous area

To eliminate a danger for persons or for the facility when the device is used in the hazardous

area (e.g. explosion protection, pressure vessel safety):

‣Based on the nameplate, check whether the ordered device is permitted for the intended

use in the hazardous area.

‣Observe the specifications in the separate supplementary documentation that is an integral

part of these Instructions.

3.5 Product safety

This measuring device is designed in accordance with good engineering practice to meet state-

of-the- art safety requirements, has been tested, and left the factory in a condition in which

they are safe to operate.

It fulfills general safety requirements and legal requirements. It also conforms to the EC

directives listed in the device-specific EC declaration of conformity. Endress+Hauser confirms

this fact by applying the CE mark.

Incoming acceptance and product identification Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA

6 Endress+Hauser

4 Incoming acceptance and product identification

4.1 Incoming acceptance

DELIVERY NOTE

1 = 2

A0016870

• Is the order code on the delivery note (1) identical to the order code on the product sticker

(2)?

• Are the goods undamaged?

• Do the data on the nameplate correspond to the order specifications and the delivery note?

• Is the documentation available?

• If required (see nameplate): Are the safety instructions (XA) present?

If one of these conditions is not fulfilled, please contact your Endress+Hauser sales office.

4.2 Storage and transport

4.2.1 Storage conditions

Use original packaging.

Store the measuring device in clean and dry conditions and protect from damage caused by

shocks (EN 837-2).

4.2.2 Transporting the product to the measuring point

LWARNING

Incorrect transport!

Housing and membrane may become damaged, and there is a risk of injury!

‣Transport the measuring device to the measuring point in its original packaging or by the

process connection.

‣Follow the safety instructions and transport conditions for devices weighing more than 18

kg (39.6 lbs).

Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA Mounting

Endress+Hauser 7

5 Mounting

5.1 Mounting requirements

5.1.1 General installation instructions

• Devices with a G 1 1/2 thread:

When screwing the device into the tank, the flat seal has to be positioned on the sealing

surface of the process connection. To avoid additional strain on the process membrane, the

thread should never be sealed with hemp or similar materials.

• Devices with NPT threads:

• Wrap Teflon tape around the thread to seal it.

• Tighten the device at the hexagonal bolt only. Do not turn at the housing.

• Do not overtighten the thread when screwing. Max. tightening torque:

20 to 30 Nm (14.75 to 22.13 lbf ft)

• For the following process connections, a tightening torque of max. 40 Nm (29.50 lbf ft) is

specified:

• Thread ISO228 G1/2 (Order option "GRC" or "GRJ" or "G0J")

• Thread DIN13 M20 x 1.5 (Order option "G7J" or "G8J")

5.1.2 Mounting sensor modules with PVDF thread

LWARNING

Risk of damage to process connection!

Risk of injury!

‣Sensor modules with PVDF thread must be installed with the mounting bracket provided!

LWARNING

Material fatigue from pressure and temperature!

Risk of injury if parts burst! The thread can become lose if exposed to high pressure and

temperature loads.

‣The integrity of the thread must be checked regularly. Also, the thread may need to be re-

tightened with the maximum tightening torque of 7 Nm (5.16 lbf ft). Teflon tape is

recommended for sealing the ½" NPT thread.

5.2 Mounting the device

5.2.1 General installation instructions

NOTICE

Damage to the device!

If a heated device is cooled during a cleaning process (e.g. by cold water), a vacuum develops

for a short time and, as a result, moisture can enter the sensor via the pressure compensation

(1).

‣Mount the device as follows.

Mounting Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA

8 Endress+Hauser

A0028471

• Keep the pressure compensation and GORE-TEX® filter (1) free from contamination.

• Do not clean or touch process membranes with hard or pointed objects.

• The process membrane in the rod and cable version is protected against mechanical damage

by a plastic cap.

• The device must be installed as follows in order to comply with the cleanability

requirements of the ASME-BPE (Part SD Cleanability):

A0028472

Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA Mounting

Endress+Hauser 9

5.2.2 FMB50

Level measurement

• Always install the device below the lowest measuring point.

• Do not install the device at the following positions:

• in the filling curtain

• in the tank outlet

• in the suction area of a pump

• at a point in the tank which could be affected by pressure pulses from the agitator.

• The calibration and functional test can be carried out more easily if you mount the device

downstream from a shutoff device.

• The Deltapilot M must also be insulated in the case of media that can harden when cold.

Pressure measurement in gases

Mount the Deltapilot M with the shutoff device above the tapping point so that any

condensate can flow into the process.

Pressure measurement in vapors

• Mount the Deltapilot M with the siphon above the tapping point.

• Fill the siphon with liquid before commissioning. The siphon reduces the temperature to

almost ambient temperature.

Pressure measurement in liquids

Mount the Deltapilot M with the shutoff device below or at the same level as the tapping

point.

Mounting Deltapilot M FMB50, FMB51, FMB52, FMB53 PROFIBUS PA

10 Endress+Hauser

5.2.3 FMB51/FMB52/FMB53

• When mounting rod and cable versions, make sure that the probe head is located at a point

as free as possible from flow. To protect the probe from impact resulting from lateral

movement, mount the probe in a guide tube (preferably made of plastic) or secure it with a

clamping fixture.

• In the case of devices for hazardous areas, comply strictly with the safety instructions when

the housing cover is open.

• The length of the extension cable or the probe rod is based on the planned level zero point.

The height of the protective cap must be taken into consideration when designing the

layout of the measuring point. The level zero point (E) corresponds to the position of the

process isolating diaphragm.

Level zero point = E; top of the probe = L.

17 (0.67)

A0023559

Autres manuels pour Deltapilot M FMB50

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Endress+Hauser Instrument de mesure

Endress+Hauser

Endress+Hauser Liquiphant M FTL51C Manuel utilisateur

Endress+Hauser

Endress+Hauser Micropilot S FMR540 Manuel utilisateur

Endress+Hauser

Endress+Hauser MemoLink Manuel utilisateur

Endress+Hauser

Endress+Hauser Profi Bus Levelflex M FMP40 Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic M FMU40 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Liquiline CM44P Caractéristiques techniques

Endress+Hauser

Endress+Hauser prosonic flow 92 Manuel

Endress+Hauser

Endress+Hauser Micropilot FMR62 Instructions d'utilisation

Endress+Hauser

Endress+Hauser Micropilot FMR62 Manuel

Endress+Hauser

Endress+Hauser Deltabar FMD72 Manuel utilisateur

Endress+Hauser

Endress+Hauser Viomax CAS51D Manuel utilisateur

Endress+Hauser

Endress+Hauser Prosonic S FMU90 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Memocheck Sim CYP03D Manuel utilisateur

Endress+Hauser

Endress+Hauser LT5 Manuel utilisateur

Endress+Hauser

Endress+Hauser StamoLys CA 71 CU Manuel utilisateur

Endress+Hauser

Endress+Hauser Cerabar M PMC51? Cerabar M PMP51 Manuel utilisateur

Endress+Hauser

Endress+Hauser PROline promag 50 w Manuel

Endress+Hauser

Endress+Hauser FQG60 Manuel de l'opérateur

Endress+Hauser

Endress+Hauser Proline t-mass 65 PROFIBUS DP Manuel utilisateur

Endress+Hauser

Endress+Hauser magphant Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar PMD55B Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag W 300 PROFINET Manuel utilisateur

Endress+Hauser

Endress+Hauser Levelflex FMP56 Caractéristiques techniques

Endress+Hauser

Endress+Hauser Proline Promass 80E Manuel

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

Acterna

Acterna MS1400 Manuel utilisateur

R&S

R&S ZPH Manuel utilisateur