Encore Networks EN-1000 Manuel utilisateur

Go to Table

of Contents

Go to EN

Product Menu

For information on trademarks, safety, limitations

of liability, and similar topics, see

https://www.encorenetworks.com/disclaimer/.

Using the EN-1000’s Management

System

he EN-1000 provides wireless and wired connections to a local area network

(LAN), to a wide area network (WAN), and to peripheral devices and remote

devices. This document describes use of the EN-1000’s browser management system.

Any platform (PC, Mac, Linux, etc.) that supports a browser (Internet Explorer,

Firefox, Chrome, Safari, etc.) can manage the EN-1000. The following sections

discuss use of the EN-1000’s management system:

•Connecting to the EN-1000

•Activating the Wireless Module

•Logging In

•Navigating the EN-1000’s Management System

•Ending the Session

2.1 Connecting to the EN-1000

The EN-1000’s management system displays in a browser window. The management

system can run on any platform (for example, a Windows, Mac, or Linux platform)

that supports a web browser.

The EN-1000’s default configuration is Cell Failover,

and the EN-1000 is fully

functional for network access. Under this configuration, the EN-1000 can be managed

via a direct connection to its Ethernet LAN port or (even if there is a management

connection to the LAN port) via a network connection that reaches the EN-1000’s WAN

port or cellular wireless port.

The LAN port on the EN-1000’s front panel (Figure 2-1) is on a private network. The

EN-1000 software includes a DHCP server that assigns an IP address to a device

connected to its LAN port. A device connected to the LAN port sees the gateway

address 192.168.10.1, representing the EN-1000.

1. For information on Quickstart configuration options, see the EN-1000™ Quick Configuration Guide.

EN-1000™ Reference Manual

Document 2

Version A.2, December 2015

Page 1-2 EN-1000™ Reference Manual, Document 2 Go to Table

of Contents

Go to EN

Product Menu

The EN-1000’s WAN port (also on the rear panel) is on a separate network from

its LAN port. The EN-1000’s WAN port is a DHCP client, by default.

2.2 Activating the Wireless Module

When the EN-1000 is powered up, upon its initial attempt to connect to the

Verizon CAT-1 LTE network, automatic over-the-air (OTA) activation does the

following:

• registers the CAT-1 LTE cellular module's International Mobile Equipment

Identity (IMEI) with the Verizon network

• registers the CAT-1 LTE cellular wireless module’s subscriber identity module

(SIM) ID with the Verizon network

• obtains the access point name (APN) from the Verizon CAT-1 LTE

Authentication, Authorization, and Accounting (AAA) server

Note: This activity can take as long as 20 minutes.

No action is required by the end user.

2.3 Logging In

1Make sure you have a terminal available to manage the EN-1000, and make

sure the terminal’s power is on.

2Connect the EN-1000 to its AC power adaptor, and plug the adaptor into an

AC outlet.

Note: The AC power adaptor must be rated for 12 volts DC.

❖The EN-1000 powers on.

3Use an Ethernet cable to connect your management terminal to the Ethernet

LAN port on the EN-1000’s rear panel.

❖The LAN port assigns an IP address to your management terminal.

Figure 2-1. EN-1000 Front Panel

Using the EN-1000’s Management System Page 1-3 Go to Table

of Contents

Go to EN

Product Menu

4On the management terminal, open a web browser.

5In the browser's address field, type the EN-1000’s gateway IP address

192.168.10.1 (or, if you prefer, type http://192.168.10.1), and press the

console’s Enter key (Figure 2-2).

Note: Instead of using a direct connection to the LAN port, you can connect

across a public network. In that case, type https:// followed by the

EN-1000’s public IP address.

Figure 2-2. Browser Address Field

Note: If the browser asks whether the EN-1000 router (192.168.10.1)

may set cookies, answer Yes, or Yes for the Session, or something

similar.

Caution: Do not block cookies for the EN-1000. Otherwise, you might not

be able to manage the EN-1000.

❖The browser navigates to the specified IP address and displays the

EN-1000 Log-In Screen (Figure 2-3).

Note: The Username field might display the user name.

Caution: The EN-1000 management system uses JavaScript in its browser-

based display. A message to enable JavaScript (similar to the message in

Figure 2-4) might display in your browser.

If you see the message in Figure 2-4, do the following:

• On the browser menu, open Tools or Options (or an equivalent menu

item in your browser).

• In the browser’s menu system, Enable JavaScript, and Save that setting.

• Right-click on the browser screen, and select Refresh, Rewrite, or

Reload (or the equivalent for your browser).

Figure 2-3. EN-1000 Log-In Screen

Figure 2-4. Message to Enable JavaScript

http://192.168.10.1

JavaScript required!

You must enable JavaScript in your browser or the management system will not work properly.

Page 1-4 EN-1000™ Reference Manual, Document 2 Go to Table

of Contents

Go to EN

Product Menu

❖The EN-1000 Log-In Screen is redisplayed, without a message to enable

JavaScript.

6Type your user name and password in the appropriate fields of the EN-1000

Log-In Screen. Use the default log-in values:

• The default user name for the EN-1000 is admin.

Note: EN-1000 routers shipped before July 09, 2018, use the default

password encore!1.

All devices, including EN-1000 routers, shipped from the factory on or after

July 09, 2018, use a randomly generated default password. That password

is in the lower right corner of a sticker on the bottom of the router's chassis.

Retain that sticker; you will need the default password if the router must be

reset.

Note: You may wish to change the password; however, save the default

password somewhere, in case you need to reset the router in the future.

Check with your network administrator for all names and passwords.

7Then press the console’s Enter key or select the screen’s Login button

(below the Log-In fields).

❖The system accepts your log-in. Then the EN-1000 Status Overview

Screen is displayed (Figure 2-5). This screen provides an overview of the

EN-1000’s status.

Note: If the EN-1000’s WAN port is connected to a network, you might see

the WAN port’s assigned IP address. (The WAN port is a DHCP client by

default.) In Figure 2-5, the IP address assigned to the WAN port is

192.168.1.151.

Figure 2-5. EN-1000 Status Overview Screen

Using the EN-1000’s Management System Page 1-5 Go to Table

of Contents

Go to EN

Product Menu

On the EN-1000 management screens, the top row of tabs indicates the

management areas.

◆Status

◆System

◆Network

◆Logout

◆Quickstart

There is a second row of tabs under each management area. The second row

provides detail for the selected management area. (The EN-1000 senses its

hardware configuration and displays tabs to represent that configuration.) In

Figure 2-5, the Status management area shows the following detail tabs:

◆Overview

◆Routes

◆System Log

◆Realtime Graphs

An Auto Refresh indicator (to the right of the Encore Networks logo) is

displayed on several screens. You can select this indicator to turn automatic

screen refreshment on or off.

8Do the following:

aTo use the EN-1000, see Navigating the EN-1000’s Management System.

bTo configure the EN-1000’s parameters, see the document Configuring the

EN-1000 for its Network Functions.

cTo review the EN-1000’s settings and performance, see the document

Monitoring the EN-1000.

2.4 Navigating the EN-1000’s Management

System

2.4.1 Saving or Discarding Changes

Buttons to Reset, Save, or Save & Apply are displayed in the lower righthand

corner of EN-1000 configuration screens. You can use them as described below:

• Select the Save & Apply button to save changes that take effect immediately.

• Select the Save button to save changes that will take effect after the EN-1000

is rebooted.

• Select the Reset button to discard changes you have made but have not yet

saved, and to see the screen with its values before you made those changes.

If you close the browser without saving changes in the configuration, the previous

configuration is used when you reopen the EN-1000 management system in the

browser.

Page 1-6 EN-1000™ Reference Manual, Document 2 Go to Table

of Contents

Go to EN

Product Menu

2.4.2 Restarting (Rebooting) the EN-1000

There may be times when the EN-1000 needs to be restarted. We recommend

using the menu system to restart the EN-1000, because that provides a

controlled approach to restarting. Any processes that are running will be shut

down properly before the router restarts.

Caution: In general, do not manually restart the EN-1000 by disconnecting

it from its power source and then reconnecting it to power. That method of

rebooting might interrupt processes running on the EN-1000.

1To restart the EN-1000, select the System management area.

2Then select the Reboot tab.

❖The System Reboot screen is displayed (Figure 2-6).

Figure 2-6. EN-1000 System Reboot

3On this screen, select Perform Reboot.

❖The menu system restarts the EN-1000. During the reboot, a message

similar to one of the messages in Figure 2-7 might be displayed.

Figure 2-7. Message while Rebooting

Note: Rebooting might take a minute or longer.

❖When the EN-1000 has rebooted, the EN-1000 Log-In Screen is displayed

(Figure 2-8).

Waiting for 192.168.10.1...

Please wait. Device rebooting.

Figure 2-8. EN-1000 Log-In Screen

Using the EN-1000’s Management System Page 1-7 Go to Table

of Contents

Go to EN

Product Menu

2.5 Ending the Session

1When you wish to log out, select the Logout tab.

❖The system logs out, and the EN-1000 Log-In Screen is redisplayed (recall

Figure 2-8).

Table des matières

Autres manuels Encore Networks Matériel réseau

Encore Networks

Encore Networks BANDIT III Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur