Emhart Teknologies PoP ProSet 3400 Manuel utilisateur

INSTRUCTION MANUAL

ProSet 3400 Series

Pneumatic Blind Rivet Tool

INSTRUCTION MANUAL

ProSet® 3400 Series

Pneumatic Blind Rivet Tool

Page 2 Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Contents

Introduction...............................................................................................................................................2

Safety Instructions....................................................................................................................................3

Specifications ...........................................................................................................................................4

Packaged Accessories..........................................................................................................................4

Tool Requirements................................................................................................................................4

ProSet®3400 Tool Dimensions.............................................................................................................5

Common Nosepieces ...........................................................................................................................6

Basic Tool Operation ................................................................................................................................6

Front End Service.................................................................................................................................7

Mandrel Collection System (MCS) – ProSet®3400 MCS .....................................................................8

Cleaning the Collector Silencer.............................................................................................................8

Tool Assembly Torque Requirements....................................................................................................9

ProSet®3400/3400MCS Diagram ..........................................................................................................10

Parts List ................................................................................................................................................12

Hydraulic Oil Charging Procedure ..........................................................................................................14

Maintenance...........................................................................................................................................15

Safety Data.............................................................................................................................................16

Troubleshooting......................................................................................................................................17

EC Declaration of Conformity .................................................................................................................18

Notes......................................................................................................................................................19

Introduction

POP ®ProSet®3400 tools are light weight, Air/Hydraulic rivet setting tools recommended for use with genuine

POP ®Brand Rivets per the following chart:

Rivet Diameter

Rivet Type Material

(Body – Mandrel) 1/8”(*)

[3.2 mm]

5/32” (*)

[4.0 mm]

3/16” (**)

[4.8 mm]

1/4” (†)

[6.4 mm]

Al – Al 9999

Al – St / SS 9999

St – St 9999

Open End & MultiGrip™

SS – SS; Mo – St /SS 9999

Al – Al 9999

Al – St / SS; Cu – St 9999

St – St 9999

Closed End

SS – SS 9999

LSR Rivets Al – Al 999(†) NA

T - Rivet Al – St 999(†) 9

Self Plugger St – St 999(†) 9

HR™ Rivets St – St 999(†) 8

HS Rivets Al – Al; St – St, NA NA NA 9

Ultra-Grip®Al – Al; St – St; SS – SS NA NA 9(†) 9

Al: Aluminum, St: Steel, SS: Stainless Steel, Cu: Cooper, Mo: Monel . (*) Use PRG540-46 Jaws and FAN276-064 Jaw Pusher set up.

(**) Use PRG540-46 Jaws and DPN276-006 Jaw Pusher set up. (†) Use PRG540-44 Jaws and DPN276-006 Jaw Pusher set up.



Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614 Page 3

Safety Instructions

TO INSURE PROPER FUNCTIONING AND SAFE OPERATION READ THIS MANUAL

CAREFULLY BEFORE SETTING UP OR OPERATING THE POP ®ProSet®3400 SERIES TOOLS

1. DO NOT use this tool in a manner other than that recommended by Emhart Teknologies.

2. Always wear eye protection when using or when near a tool that is in use.

3. This tool is NOT designed for use in explosive atmospheres.

4. Inspect tool for damage before connecting to air supply including all air connections.

5. Trained personnel must perform tool repair and/or maintenance at the prescribed intervals.

6. Disconnect the air supply when adjusting, servicing or removing any part of the tool.

7. Keep fingers off the trigger when connecting the air supply or if the air supply fails.

8. Keep fingers away from the front of the tool when connecting the air supply or setting rivets.

9. DO NOT point the tool at anyone.

10. DO NOT operate tool with the Nose Housing removed.

11. DO NOT operate tool without the Deflector or Collector.

12. DO NOT modify the tool in any way. Modification will make void any applicable warranties

and could result in damage to the tool or physical injury to the user.

13. DO NOT look into the tool from the front or the back during use or when connected to air

supply.

14. The operating pressure must not exceed 100 psi (6.9 bar).

15. DO NOT direct tool exhaust towards anyone.

16. Wash hands if exposed to hydraulic fluid or lubricant.

17. Keep hair, fingers and loose clothing away from moving parts of the tool.

Page 4 Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Specifications

ProSet®3400 ProSet®3400MCS

Weight 4.19 lbs. (1.90 kg) 4.41 lbs. (2.00 kg)

Length 12.17” (309 mm) 13.15” (344 mm)

Height 12.44” (316 mm) 10.20” (316 mm)

Stroke 1.02” (26 mm) 1.02” (26 mm)

Air Consumption 0.172 cu. ft. per rivet

(4.86 lper rivet)

2.83 scfm (max.)

(80 l/min (max.))

Pulling Force 4160 lbs. @ 90 psi (18500 N @ 0.62 MPa)

Noise Level LAeq,T = 78.5 dB(A), LWA = 84.0 dB(A), LPeak = 103.6 dB(C)

Vibration Level 0.61 m/s2, Time to 2.5 m/s2> 24hrs (EAV)

Packaged Accessories

Qty Item ProSet®3400 ProSet®3400MCS Part No.

1 ProSet®3400 Rivet Tool 99-

1 Operating Instructions 99P449

1 Maintenance Manual 99P551

1 Nosepiece for 4 size open end rivets 99PRN414

1 Nosepiece for 5 size open end rivets 99PRN514

1 Nosepiece for 6 size open end rivets 99PRN614

1 Nosepiece for 8 size open end rivets Installed Installed PRN811

1 Jaw Pusher (Assy) for 4&5 size rivets 99FAN276-064

1 Air Line Assembly 99FAN276-154

1 4 mm Hex. Socket Screw Key 99DPN239-139

1 Warranty Card 99FG2184

Tool Requirements

Air supply * 6 scfm (150 l/min) Minimum

Recommended Operating Pressure 72.5-90 PSI (0.50-0.62 MPa) dry, filtered

Maximum Operating Pressure 100 PSI (0.69 MPa) dry, filtered

Hydraulic Oil ** POP ®p/n: PRG540-130 [1 qt. (.945 ml)]

Jaw Lubricant ** POP ®p/n: PRG510-130 [6 oz. (177 ml)]

Seal Lubricant ** POP ® p/n: PSA075508P [1 ¾ oz. (54 g)]

(*) Note: For best results and long service life, use dry, filtered air supply.

(**) Note: See lubricant safety information.

•

Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614 Page 5

ProSet®3400 Tool Dimensions

ProSet

3400 MCS

ProSet

3400

4.21” (107 mm)

.882” (22.4 mm)

12.17” (309 mm)

12.44” (316 mm)

4.21” (107 mm)

2.32” (59 mm)

4.06”

(103 mm)

2.66” (67.5 mm)

4.21” (107 mm)

.882” (22.4 mm)

12.44” (316 mm)

4.06”

(103 mm)

2.66” (67.5 mm)

2.32” (59 mm)

13.15” (334 mm)

Page 6 Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Common Nosepieces

* Included with the tool

For T-Rivets use PRN625 nosepiece when using 3/16” (4.8mm) diameter rivets and PRN825 for ¼” (6.4mm)

diameter rivets. For Monobolt®rivets use N-410 nosepiece for 3/16” (4.8mm) and N-414 for ¼” (6.4mm)

diameter rivets.

Basic Tool Operation

Before operating the tool check the following:

Inspect tool for damage or leaking oil – do not use tool if it is damaged or leaking oil.

Check that correct nosepiece is fitted and tightened to 60 - 65 in-lbs [6.8 – 7.3 N-m] torque.

Check that the Nose Housing Nut (8) is tight – hand tighten only.

Connect tool to air supply – see air supply requirements (page 4).

Fit Mandrel Collector (113) – (MCS tool only).

Open air supply valve by sliding red OS Slider (130) on side of tool (see note below).

Insert rivet into nosepiece.

Position rivet in work piece.

Pull trigger to set rivet.

Release trigger – if equipped, MCS suction will draw spent mandrel into the collector.

!Note: The ProSet®3400 has an OS (Open-Shut) Valve for switching the air supply ON and OFF to

save air when the tool is not in use.

Closed End HR Rivets

Rivet

Diameter Open End Steel

Mandrel

Aluminum

Mandrel

Aluminum

Body

Steel

Body

HS Rivets Ultra-Grip®Jaw Pusher

1/8”

(3.2 mm) PRN414* PRN424 PRN434 PRN414* PRN4HR - -

5/32”

(4.0 mm) PRN514* PRN524 PRN534 PRN514* PRN5HR - -

FAN276-064*

3/16”

(4.8 mm) PRN614* PRN624 PRN634 PRN614* PRN6HR - N-406

1/4”

(6.4 mm) PRN811* PRN822 - PRN811* - PRN8PS

PRN8PS or

N-407

DPN276-006*

Air Supply ON: Open OS Valve

by sliding OS Slider in the

direction shown (up).

Air Supply OFF: Close OS Valve

by sliding OS Slider in the

direction shown (down).

OS Slider

Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614 Page 7

Front End Service

For optimum tool performance, Front-End maintenance should be performed regularly as per the “Preventative

Maintenance Schedule”.

!Note: UNPLUG AIR SUPPLY while servicing front-end to avoid INJURY.

1. REMOVE NOSE HOUSING:

Unscrew the Nose Housing Nut by hand and

slide Nose Housing off the tool.

2. REMOVE JAW GUIDE TO ACCESS JAWS

AND INTERNAL PARTS:

Pull back the Jaw Guide Lock to disengage the

Jaw Guide Lock teeth and unscrew and remove

the Jaw Guide.

Remove Jaws, Jaw Pusher, and Jaw Pusher

Spring for servicing.

3. CLEAN PARTS:

Clean Jaws, Jaw Guide, Jaw Pusher, Spring

and thread area of the Pulling Head.

Apply Seal Lubricant to outside surface of Jaws

and inside surface of the Jaw Guide.

4. REASSEMBLY OF INTERNAL PARTS AND JAW

GUIDE:

Place the Jaws into the Jaw Guide and slide the Jaw

Pusher Spring and Jaw Pusher into the Pulling Head.

Apply a small amount of Seal Lubricant to the Pulling

Head threads and Jaw Guide Lock teeth. Screw the Jaw

Guide onto the Pulling Head until it stops. Check to

make sure the teeth are engaged.

Apply Jaw Lubricant to the Jaw area by submerging the

assembled Jaw Guide into Jaw lube about 1 in. (25mm).

Clean off excess Jaw Lube from the outside of the Jaw

Guide.

(! Make sure the air supply is disconnected !)

5. REINSTALL NOSE HOUSING ASSEMBLY:

Refit the Nose Housing and hand-tighten the Nose

Housing Nut securely against the O-Ring. If the nut is

not tightened sufficiently against the O-Ring there may

be a loss of suction on the MCS tool version.

Nose Housing

Nose Housing Nut

Wrench Flat

Jaw Guide

Pulling Head

Jaw Guide Lock

Housing Adapter

O-Ring

Jaw Guide Lock motion

Pulling Head Locking Teeth.

Jaw Guide teeth

Page 8 Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Collector Silencer (119)

Collector End (121)

Collector End Cap (120)

Collector End Nut (122)

Mandrel Collection System (MCS) – ProSet®3400 MCS

For safety purposes, removing the Collector from the tool automatically turns the MCS suction OFF. Refitting

the Collector turns the MCS suction ON.

Cleaning the Collector Silencer

For optimum performance, the Collector Silencer should be cleaned at regular intervals as per the

“Preventative Maintenance Schedule”.

!Note: UNPLUG AIR SUPPLY while servicing Collector to avoid INJURY.

1. CLEAN THE COLLECTOR :

•Remove and empty the Collector (113) by turning counterclockwise.

•Remove the Collector End Nut (122) (17mm wrench) and remove the Collector End Cap (120).

•Remove the Collector Silencer (119).

•Clean and remove debris from all components.

Collector Body (118)

MCS suction ON MCS suction OFF

Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614 Page 9

2. RE-ASSEMBLE THE COLLECTOR :

•Secure Collector End (121) to Collector Body (118). Use a screwdriver or similar tool to hold the

Collector End in place during re-assembly (see picture below).

•Place the Collector Silencer (119) onto the Collector End (121).

•Place Collector End Cap (120) on Collector End (121).

•Install and tighten Collector End Nut (122) on Collector End (121).

Tool Assembly Torque Requirements

Item Part No. Description Torque Value

137

136

135

PRN811

PRN614

PRN514

PRN414

Nosepiece 8 size

Nosepiece 6 size

Nosepiece 5 size

Nosepiece 4 size

60 – 65 in-lbs (6.8 – 7.3 N-m)

61 DPN276-031 Sleeve Lower 55 - 63 ft-lbs (75 - 85 N-m)

81 DPN276-043 Sleeve Lock Nut 44 - 52 ft-lbs (60 - 70 N-m)

111 DPN907-003 Socket Head Cap Screw 46 - 51 in-lbs (5.2 – 5.8 N-m)

See exploded ProSet®3400/3400MCS Diagram

Screwdriver

ProSet

3400/3400MCS Diagram

Page 10



Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

Page 10 Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614

ProSet®3400/3400MCS Diagram

Ce manuel convient aux modèles suivants

Autres manuels Emhart Teknologies Outils électriques

Emhart Teknologies

Emhart Teknologies POP NUT PNT800A Manuel utilisateur

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel