Emerson Rosemount 2120 Manuel utilisateur
Quick Start Guide
00825-0100-4030, Rev GB
March 2022
Rosemount™ 2120 Level Switch
Vibrating Fork
Contents
About this guide...........................................................................................................................3
Installation................................................................................................................................... 5
Prepare the electrical connections..............................................................................................11
Connect wiring and power up.....................................................................................................26
Configuration.............................................................................................................................30
Operation...................................................................................................................................32
Quick Start Guide March 2022
2 Rosemount 2120 Level Switch
1 About this guide
This Quick Start Guide provides basic guidelines for the Rosemount 2120.
Refer to the Rosemount 2120 Reference Manual for more instructions. The
manual and this guide are also available electronically at
Emerson.com/Rosemount.
1.1 Safety messages
WARNING
Failure to follow safe installation and servicing guidelines could result in
death or serious injury.
Ensure the level switch is installed by qualified personnel and in accordance
with applicable code of practice.
Use the level switch only as specified in this manual. Failure to do so may
impair the protection provided by the level switch.
The weight of a level switch with a heavy flange and extended fork length
may exceed 37 lb. (18 kg). A risk assessment is required before carrying,
lifting, and installing the level switch.
Repair, e.g. substitution of components, etc. may jeopardize safety and is
under no circumstances allowed.
WARNING
Explosions could result in death or serious injury.
Verify the operating atmosphere of the level switch is consistent with the
appropriate hazardous locations certifications.
Before connecting a handheld communicator in an explosive atmosphere,
ensure the instruments are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
In explosion-proof/flameproof and non-incendive installations, do not
remove the housing cover when power is applied to the level switch.
The housing cover must be fully engaged to meet flameproof/explosion-
proof requirements.
March 2022 Quick Start Guide
Quick Start Guide 3
WARNING
Electrical shock could cause death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be
present on leads can cause electrical shock.
Ensure the power to the level switch is off, and the lines to any other external
power source are disconnected or not powered while wiring the level switch.
Ensure the wiring is suitable for the electrical current and the insulation is
suitable for the voltage, temperature, and environment.
WARNING
Process leaks could result in death or serious injury.
Ensure the level switch is handled carefully. If the process seal is damaged,
gas might escape from the vessel (tank) or pipe.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to and/or
misconfiguration of end users’ equipment. This could be intentional or
unintentional and needs to be protected against.
Physical security is an important part of any security program and
fundamental to protecting your system. Restrict physical access by
unauthorized personnel to protect end users’ assets. This is true for all
systems used within the facility.
CAUTION
Hot surfaces
The flange and process seal may be hot at high process temperatures. Allow
to cool before servicing.
Quick Start Guide March 2022
4 Rosemount 2120 Level Switch
2 Installation
2.1 Fork alignment in a pipe installation
The fork is correctly aligned by positioning the groove or notch as indicated
(Figure 2-1).
Figure 2-1: Correct Fork Alignment for Pipe Installation
A
B
A
B
OK
OK
A. Tri Clamp process connections have a circular notch
B. Threaded process connections have a groove
2.2 Fork alignment in a vessel (tank) installation
The fork is correctly aligned by positioning the groove or notch as indicated
(Figure 2-2).
Figure 2-2: Correct Fork Alignment for Vessel (Tank) Installation
A
B
C
OK OK
OK
A. Tri Clamp process connections have a circular notch
B. Threaded process connections have a groove
C. Flanged process connections have a circular notch
March 2022 Quick Start Guide
Quick Start Guide 5
2.3 Mounting the threaded version
2.3.1 Threaded vessel (tank) or pipework connection
Procedure
1. Seal and protect the threads. Use anti-seize paste or PTFE tape
according to site procedures.
A gasket may be used as a sealant for BSPP (G) threaded connections.
2. Screw the level switch into the process connection.
Note
Tighten using the hexagon nut only.
Figure 2-3: Vertical Installation
A
A. Gasket for BSPP (G) threaded connection
Figure 2-4: Horizontal Installation
A
A. Gasket for BSPP (G) threaded connection
Quick Start Guide March 2022
6 Rosemount 2120 Level Switch
2.3.2 Threaded flange connection
Procedure
1. Place the customer-supplied flange and gasket on the vessel (tank)
nozzle.
A
A. Gasket (customer supplied)
2. Tighten the bolts and nuts with sufficient torque for the flange and
gasket.
3. Seal and protect the threads. Use anti-seize paste or PTFE tape
according to site procedures.
A gasket may be used as a sealant for BSPP (G) threaded connections.
March 2022 Quick Start Guide
Quick Start Guide 7
4. Screw the level switch into the flange thread.
Note
Tighten using the hexagon nut only.
A
A. Gasket for BSPP (G) threaded connection
2.4 Mounting the flanged version
Procedure
1. Lower the level switch into the nozzle.
A
A. Gasket (customer supplied)
Quick Start Guide March 2022
8 Rosemount 2120 Level Switch
2. Tighten the bolts and nuts with sufficient torque for the flange and
gasket.
2.5 Mounting the Tri Clamp version
Procedure
1. Lower the level switch into the flange face.
A
A. Seal (supplied with Tri Clamp)
March 2022 Quick Start Guide
Quick Start Guide 9
2. Fit the Tri Clamp.
Quick Start Guide March 2022
10 Rosemount 2120 Level Switch
Autres manuels pour Rosemount 2120
5
Table des matières
Autres manuels Emerson Changer
Emerson
Emerson Rosemount 2521 Series Manuel utilisateur
Emerson
Emerson SC885 Manuel utilisateur
Emerson
Emerson Rosemount 2130 Manuel utilisateur
Emerson
Emerson AVOCENT Manuel utilisateur
Emerson
Emerson Penberthy MGS-314 Series Manuel
Emerson
Emerson Rosemount 2110 Manuel utilisateur
Emerson
Emerson Fisher GH04148 Manuel utilisateur
Emerson
Emerson 80 Series GO Switch Manuel utilisateur
Emerson
Emerson TopWorx TX Series Manuel utilisateur
Emerson
Emerson Avocent SV 220 Manuel utilisateur
Emerson
Emerson Alco Controls PS1 Series Manuel utilisateur
Emerson
Emerson ASCO 7000 Series Manuel utilisateur
Emerson
Emerson Alco Controls PS1 Series Manuel utilisateur
Emerson
Emerson ASCO 7000 Series Manuel utilisateur
Emerson
Emerson ASCO 7000 Series Manuel utilisateur
Emerson
Emerson Avocent SV 220D Manuel utilisateur
Emerson
Emerson SCKM120 Manuel utilisateur
Emerson
Emerson SC 820 Manuel utilisateur
Emerson
Emerson Rosemount FS-IR-975 Manuel utilisateur
Emerson
Emerson AVENTICS PM1 Manuel utilisateur
