Emerson Rosemount Analytical 400A Manuel utilisateur

Rosemount Analytical

MODEL 400A

HYDROCARBON ANALYZER

INSTRUCTION MANUAL

NOTE

THIS MANUAL IS APPLICABLE TO MODEL 400A, CATALOG NUMBER 194106

WITH SERIAL NUMBERS BEGINNING WITH 2000001

748262-K

NOTICE

The information contained in this document is subject to change without notice.

Instruction Manual 748262-K

July 1997

Printed in USA

Rosemount Analytical Inc.

4125 East La Palma Avenue

Anaheim, California 92807-1802

Teflon®is a registered trademark of E.I. duPont de Nemours and Co., Inc.

SNOOP®is a registered trademark of NUPRO Co.

CONTENTS

748262-K Rosemount Analytical July 1997 I

Model 400A Hydrocarbon Analyzer

PREFACE

SAFETY SUMMARY ..........................................................................................P-1

SPECIFICATIONS..............................................................................................P-3

CUSTOMER SERVICE, TECHNICAL ASSISTANCE AND FIELD SERVICE....P-5

RETURNING PARTS TO THE FACTORY.........................................................P-5

TRAINING ......................................................................................................P-5

DOCUMENTATION............................................................................................P-5

SECTION 1. INTRODUCTION

1.1 DESCRIPTION.........................................................................................1-1

1.2 ANALYZER MOUNTING OPTIONS.........................................................1-1

1.3 FUEL GAS OPTIONS...............................................................................1-2

1.4 OUTPUT OPTIONS..................................................................................1-3

1.4.1 Isolated Remote Range Change and Identification ....................1-4

1.4.2 Range Trim Option......................................................................1-4

1.5 SAMPLE PUMP OPTION.........................................................................1-4

1.6 GAS SAFETY FEATURES.......................................................................1-4

SECTION 2. INSTALLATION

2.1 UNPACKING............................................................................................2-1

2.2 LOCATION...............................................................................................2-1

2.3 VOLTAGE REQUIREMENTS...................................................................2-1

2.4 FUEL AND AIR REQUIREMENTS...........................................................2-2

2.4.1 Fuel Gas.....................................................................................2-2

2.4.2 Air ......................................................................................2-3

2.5 SAMPLE HANDLING................................................................................2-3

2.6 GAS CONNECTION.................................................................................2-4

2.7 LEAK CHECK...........................................................................................2-6

CONTENTS

ii July 1997 Rosemount Analytical 748262-KModel 400A Hydrocarbon Analyzer

SECTION 2. (CONTINUED)

2.8 ELECTRICAL CONNECTIONS ............................................................... 2-6

2.8.1 Line Power Connections ............................................................ 2-6

2.8.2 Voltage Output Selection and Cable Connections for

Recorder....................................................................... 2-7

2.8.3 Voltage to Current Output Board (optional)................................ 2-7

2.8.4 Auxiliary Contacts....................................................................... 2-7

2.8.5 Remote Range Control and Indication....................................... 2-7

2.8.6 Sample Pump Accessory........................................................... 2-9

SECTION 3. STARTUP AND CALIBRATION

3.1 INITIAL STARTUP AND CALIBRATION.................................................. 3-1

3.1.1 Selection of Calibration Method and Assoicated Standard

Gas(es)......................................................................... 3-4

3.2 CALIBRATION PROCEDURE ................................................................. 3-5

3.3 RANGE SWITCH..................................................................................... 3-7

3.4 RANGE TRIM OPTION............................................................................ 3-8

SECTION 4. OPERATION

4.1 ROUTINE OPERATION........................................................................... 4-1

4.2 RECOMMENDED CALIBRATION FREQUENCY.................................... 4-1

4.3 SHUTDOWN............................................................................................ 4-1

4.4 OBTAINING MAXIMUM SENSITIVITY.................................................... 4-2

SECTION 5. THEORY

5.1 PRINCIPLE OF OPERATION.................................................................. 5-1

5.2 BURNER.................................................................................................. 5-1

5.2.1 Response to Different Hydrocarbons......................................... 5-2

5.3 ANALYZER FLOW SYSTEM................................................................... 5-4

5.4 PREAMPLIFIER BOARD......................................................................... 5-4

5.5 MAIN ELECTRONICS BOARD................................................................ 5-5

5.5.1 Post Amplifier............................................................................. 5-5

5.5.2 Digital Display............................................................................. 5-5

5.5.3 Span ..................................................................................... 5-6

5.5.3.1 Range Trim (Option)................................................... 5-6

5.5.4 Remote Range Control............................................................... 5-6

5.6 HEATER/FAN TEMPERATURE ASSEMBLY.......................................... 5-6

CONTENTS

748262-K Rosemount Analytical July 1997 iii

Model 400A Hydrocarbon Analyzer

SECTION 5. (CONTINUED)

5.7 IGNITION CIRCUIT..................................................................................5-7

5.8 SYSTEM POWER SUPPLIES..................................................................5-7

5.9 FLAME-OUT BOARD...............................................................................5-8

SECTION 6. SERVICE AND TROUBLESHOOTING

6.1 SYSTEM CHECKOUT..............................................................................6-1

6.2 SERVICING FLOW SYSTEM AND BURNER..........................................6-2

6.2.1 Burner Disassembly and Cleaning..............................................6-3

6.2.2 Thermistor...................................................................................6-4

6.2.3 Fuel and Air Restrictors ..............................................................6-4

6.2.4 Sample Capillary.........................................................................6-4

6.3 TROUBLESHOOTING .............................................................................6-4

SECTION 7. REPLACEMENT PARTS

7.1 CIRCUIT BOARD REPLACEMENT POLICY ...........................................7-1

7.2 RECOMMENDED REPLACMENT PARTS LIST......................................7-1

GENERAL PRECAUTIONS FOR HANDLING & STORING HIGH PRESSURE CYLINDERS

WARRANTY

FIELD SERVICE AND REPAIR FACILITIES

CONTENTS

iv July 1997 Rosemount Analytical 748262-KModel 400A Hydrocarbon Analyzer

FIGURES

2-1 Range Input-Output Board....................................................................... 2-8

2-2 Range Control and Output Connections.................................................. 2-10

3-1 Power Switch Location............................................................................. 3-2

3-2 Typical Curves of Downscale Response vs. Time for Various

Hydrocarbons............................................................................... 3-5

3-3 Example 1 Display................................................................................... 3-7

3-4 Example 2 Display................................................................................... 3-8

3-5 Example 3 Display................................................................................... 3-8

3-6 Range Trim Option Schematic................................................................. 3-9

4-1 Typical Curve of Analyzer Response vs. Pressure Setting on Sample

Pressure Regulator....................................................................... 4-2

4-2 Typical Curves of Analyzer Response vs. Pressure Setting on Fuel Pressure

Regulator...................................................................................... 4-3

4-3 Typical Curves of Analyzer Response vs. Pressure Setting on Air

Pressure Regulator....................................................................... 4-3

5-1 Flame Ionization Detection Theory.......................................................... 5-1

5-2 Typical Curves of Downscale Response vs. Time for Various

Hydrocarbons............................................................................... 5-2

TABLES

1-1 Fuel Gas vs. Analyzer Characteristics..................................................... 1-3

2-1 Range Control.......................................................................................... 2-8

3-1 Internal Pressure Regulators Settings..................................................... 3-2

3-2 Range Switch Settings............................................................................. 3-7

5-1 Approximate Effective Carbon Numbers.................................................. 5-3

5-2 Input Sensitivities..................................................................................... 5-5

5-3 Fullscale Sensitivity.................................................................................. 5-6

6-1 Troubleshooting....................................................................................... 6-5

CONTENTS

748262-K Rosemount Analytical July 1997 v

Model 400A Hydrocarbon Analyzer

DRAWINGS (LOCATED IN REAR OF MANUAL)

620424 Schematic Diagram, Preamplier

620429 Schematic Diagram, Main Electronics

620434 Schematic Diagram, Isolated V/I

622883 Flow Diagram, Model 400A

623190 Burner Parts List

624003 Schematic Diagram, Temperature Control Board

654328 Installation Drawing, Model 400A

654905 Schematic Diagram, Relay Board

654910 Schematic Diagram, Relay Board

654913 Assembly Instructions, I/O Board

654998 Assembly Instructions, Relay Board

655354 Pictorial Wiring Diagram, Model 400A

657546 Schematic Diagram, Flame-Out Board

CONTENTS

vi July 1997 Rosemount Analytical 748262-KModel 400A Hydrocarbon Analyzer

NOTES

PREFACE

748262-K Rosemount Analytical July 1997 P-1

Model 400A Hydrocarbon Analyzer

CAUTION: HIGH PRESSURE GAS CYLINDERS

SAFETY SUMMARY

To avoid explosion, loss of life, personal injury and damage to this equipment and

on-site property, all personnel authorized to install, operate and service the Model

400A Hydrocarbon Analyzer should be thoroughly familiar with and strictly follow the

instructions in this manual. Save these instructions.

DANGER is used to indicate the presence of a hazard which will cause severe

personal injury, death, or substantial property damage if the warning is ignored

WARNING is used to indicate the presence of a hazard which can cause severe

personal injury, death, or substantial property damage if the warning is ignored.

CAUTION is used to indicate the presence of a hazard which will or can cause minor

personal injury or property damage if the warning is ignored.

NOTE is used to indicate installation, operation, or maintenance information which is

important but not hazard-related.

Do not operate without doors and covers secure. Servicing requires access to

live parts which can cause death or serious injury. Refer servicing to qualified

personnel.

For safety and proper performance this instrument must be connected to a

properly grounded three-wire source of power.

This analyzer requires periodic calibration with known zero and standard gases.

Refer to Sections 2.6, 3.8, 3.9, 3.10 and 3.11. See also General Precautions for

Handling and Storing High Pressure Cylinders, following Section 7.

WARNING: ELECTRICAL SHOCK HAZARD

PREFACE

P-2 July 1997 Rosemount Analytical 748262-KModel 400A Hydrocarbon Analyzer

CAUTION: TOPPLING HAZARD

WARNING: PARTS INTEGRITY

WARNING: POSSIBLE EXPLOSION HAZARD

Do not apply power to analyzer or ignite burner until all leak checks have been

performed and until the environment of the analyzer has been determined to be

non-hazardous. See Section 2.7 for leak check procedure.

This instrument uses a fuel containment hydrogen. The instrument is designed to

protect against the formation of an explosive gas mixture within the enclosure. It

must NOT be operated if the internal ventilation fan is not functioning. Do NOT

operate without factory installed fuel flow restrictor in place.

Check the fuel supply and containment system for leaks, both inside and outside the

analyzer, upon installation, before initial startup, during routine maintenance, or any

time the integrity of the fuel containment system is broken, to assure that the system

is leak-tight. Refer to Leak Check Procedure, Section 2.7, Step 6.

The enclosure is protected by a continuous dilution air purge system, as

recommended in IEC* Publication 79-2 (Third Edition - 1983). Do not operate unit

unless the continuous dilution purge system is properly installed and

functioning. Upon startup or loss of pressurization, purge for fifteen minutes

before restoring power unless the internal atmosphere is known to be

non-explosive.

Tampering or unauthorized substitution of components may adversely affect

safety of this product. Use only factory documented components for repair.

This instrument’s internal pullout chassis is equipped with a safety stop latch

located on the left side of the chassis.

When extracting the chassis, verify that the safety latch is in its proper (counter-

clockwise) orientation.

If access to the rear of the chassis is required, the safety stop may be overridden by

lifting the latch; however, further extraction must be done very carefully to insure the

chassis does not fall out of its enclosure.

If the instrument is located on top of a table or bench near the edge, and the chassis

is extracted, it must be supported to prevent toppling.

Failure to observe these precautions could result in personal injury and/or damage to

the product.

Autres manuels pour Rosemount Analytical 400A

Table des matières

Autres manuels Emerson Instrument de mesure

Emerson

Emerson TopWorx 4310 Manuel utilisateur

Emerson

Emerson Rosemount 9175 Manuel utilisateur

Emerson

Emerson DIXELL XWEB1000D PRO Schéma de câblage

Emerson

Emerson RLDS Mode d'emploi

Emerson

Emerson Nelson CM-1 Manuel utilisateur

Emerson

Emerson Micro Motion 1700 Guide rapide

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson ROSEMOUNT 485 Annubar Pak-Lok Manuel utilisateur

Emerson

Emerson Lumity IC100D EVO Manuel utilisateur

Emerson

Emerson 250-5000 Manuel utilisateur

Emerson

Emerson Rosemount 3051 Manuel utilisateur

Emerson

Emerson Rosemount 2130 Manuel utilisateur

Emerson

Emerson A6312 Manuel utilisateur

Emerson

Emerson Rosemount 1057 Manuel utilisateur

Emerson

Emerson RXi HMI Manuel utilisateur

Emerson

Emerson Rosemount FCL Manuel utilisateur

Emerson

Emerson Micro Motion SGM Series Guide rapide

Emerson

Emerson Rosemount 2555 Manuel utilisateur

Emerson

Emerson FB2100 Manuel utilisateur

Emerson

Emerson Machinery Health Expert CSI 2600 Manuel utilisateur

Emerson

Emerson Rosemount 1056 Manuel utilisateur

Emerson

Emerson Rosemount 8600 Series Manuel utilisateur

Emerson

Emerson Rosemount 3410 Series Manuel de programmation

Emerson

Emerson Rosemount Wireless Pressure Gauge Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur