Emerson PACSystems RX3i Energy Pack Manuel utilisateur

QUICK START GUIDE

GFK-3000B

Sep 2019

PACSystemsTM RX3i

RACKLESS ENERGY PACK

(IC695ACC403)

Overview ii 
Contents 
1Overview..................................................................................... 2 
2Hardware Installation.................................................................. 4 
2.1 Mounting the Energy Pack on a DIN Rail ...............................................................4 
2.2 Panel-Mounting the Energy Pack..........................................................................5 
3Cable Connections ....................................................................... 6 
3.1 Connect Input Power to Energy Pack....................................................................7 
3.2 Connecting the Energy Pack to the Controller......................................................8 
4Grounding ................................................................................... 9 
5Initial Power-up......................................................................... 10 
6LED and Status Indications......................................................... 11 
6.1 LED Indications: Special Cases ............................................................................12 
6.2 Energy Pack Status Bit Operation........................................................................12 
7Replacing the CAP Pack Module................................................. 13 
8Firmware Updates ..................................................................... 15 
8.1 LED Indications for Firmware Updates ................................................................15 
9Additional Information.............................................................. 16 
 
 

Quick Start Guide Chapter 1

GFK-3000B Sep 2019

iii

Caution Notes as Used in this Publication

Caution notices are used where equipment might be damaged if care is

not taken.

Caution

Note: Notes merely call attention to information that is especially significant to understanding

and operating the equipment.

These instructions do not purport to cover all details or variations in equipment, nor to provide for

every possible contingency to be met during installation, operation, and maintenance. The

information is supplied for informational purposes only, and Emerson makes no warranty as to the

accuracy of the information included herein. Changes, modifications, and/or improvements to

equipment and specifications are made periodically and these changes may or may not be reflected

herein. It is understood that Emerson may make changes, modifications, or improvements to the

equipment referenced herein or to the document itself at any time. This document is intended for

trained personnel familiar with the Emerson products referenced herein.

Emerson may have patents or pending patent applications covering subject matter in this

document. The furnishing of this document does not provide any license whatsoever to any of these

patents.

Emerson provides the following document and the information included therein as-is and without

warranty of any kind, expressed or implied, including but not limited to any implied statutory

warranty of merchantability or fitness for particular purpose.

Quick Start Guide Chapter 1

GFK-3000B Sep 2019

Overview 2

1Overview

An Energy Pack is used in conjunction with a Controller to preserve user memory in

the Controller during power fluctuations or outages.

If system power is lost, the Energy Pack maintains power long enough for a

Controller to write its user memory contents to non-volatile memory. When system

power is restored, the user memory is restored if the Controller is configured to

power up from RAM.

Figure 1.1: Interconnect Wiring Diagram

Quick Start Guide Chapter 1

GFK-3000B Sep 2019

Overview 3

Ordering Information

IC695ACC403

Energy Pack. Includes base, CapPack module and

Energy Pack to Controller cable.

IC695ACC413

Replacement CapPack module.

IC695CBL003

Replacement 0.6m (24”) Energy Pack to

Controller cable.

Quick Start Guide Chapter 2

GFK-3000B Sep 2019

Hardware Installation 4

2Hardware Installation

The Energy Pack can be mounted on a standard EN50022 DIN rail or an equipment

panel. It is designed to be mounted adjacent to the Controller and connected to the

Controller using the provided cable (IC695CBL003).

Heat dissipation: When mounting the Energy Pack, allow a minimum clearance of

25.4mm (1 inch) on all four sides of the unit (right, left, top and the bottom).

2.1 Mounting the Energy Pack on a DIN Rail

The Energy Pack snaps easily onto the DIN rail. No tools are required.

1) Incline Energy Pack so that top edge of plastic recess (Figure 2.1) engages

top of DIN rail

2) Swivel the Energy Pack so that bottom spring-loaded plastic clip engages

bottom of DIN rail.

3) Listen for click as plastic clip springs back, securing the Energy Pack onto

the DIN rail.

Quick Start Guide Chapter 2

GFK-3000B Sep 2019

Hardware Installation 5

Figure 2.1: Snap Mount to DIN Rail

2.2 Panel-Mounting the Energy Pack

Recommended fasteners:

Four M4-0.7 machine screws with minimum length of 25mm (or 8-32, 1”

min. length) and nuts.

•Over tightening the mounting screws could crack the plastic housing.

Caution

Quick Start Guide Chapter 3

GFK-3000B Sep 2019

Cable Connections 6

3Cable Connections

Figure 3.1: Input Power and Output Power/Control Connections

Quick Start Guide Chapter 3

GFK-3000B Sep 2019

Cable Connections 7

3.1 Connect Input Power to Energy Pack

IMPORTANT

Before connecting input power, see complete installation instructions in the

PACSystems Controllers: Battery and Energy Pack Manual, GFK-2741E or later.

You will need:

•A 24Vdc, 72W SELV power supply

•A power cord with 18 AWG (0.82mm2) copper wires

•An 18 AWG (0.82mm2) copper wire for frame ground

•An input power terminal block –provided (Weidmuller part number

1748010000)

•A small flat-head screwdriver (such as a 1.4mm jeweler’s screwdriver)

1. Using the power cord, connect the power supply output to the Energy Pack’s

input power terminal block.

To insert the wires in the power terminal block connector, you may need to

use the small screwdriver to release the spring clamp on the terminal block.

Recommended wire stripping length is 7mm (0.28 in).

Quick Start Guide Chapter 3

GFK-3000B Sep 2019

Cable Connections 8

Figure 3.2: Energy Pack Input Power Mating Connector (bottom view)

2. Insert the plug into the Energy Pack’s Input Power connector and securely

tighten the attaching screws.

3.2 Connecting the Energy Pack to the Controller

With power to the system turned off, use the supplied cable (IC695CBL003)

to connect the output of the Energy Pack (green connector) to the 24Vdc

input on the Controller (3-pin green connector) and to the serial

communication link (using the 5-pin green connector). Refer to Figure 4.1.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Contrôleurs

Emerson

Emerson NZ Series Manuel utilisateur

Emerson

Emerson FISHER 670 Series Manuel utilisateur

Emerson

Emerson Dixell XR03CH Schéma de câblage

Emerson

Emerson Fisher 4195KA Manuel utilisateur

Emerson

Emerson Asco 642 Series Manuel utilisateur

Emerson

Emerson Tartarini FL Manuel utilisateur

Emerson

Emerson Dixell iPro Master IPM500D Schéma de câblage

Emerson

Emerson Fisher EZR Manuel utilisateur

Emerson

Emerson Dixell XR44CH Schéma de câblage

Emerson

Emerson 2202 Instructions de montage

Emerson

Emerson CASH VALVE A-360 Manuel

Emerson

Emerson EXD-TEVI Manuel utilisateur

Emerson

Emerson Bettis GVO-C Series Mode d’emploi

Emerson

Emerson Bettis SMART EHO G Series Mode d'emploi

Emerson

Emerson Fisher 1305 Series Manuel utilisateur

Emerson

Emerson Fisher MR95 Series Manuel utilisateur

Emerson

Emerson Fisher SR5 Manuel utilisateur

Emerson

Emerson Fisher 667 Manuel utilisateur

Emerson

Emerson Dixell XV308K Manuel utilisateur

Emerson

Emerson PMAC II Manuel utilisateur

Emerson

Emerson unidrive sp Manuel utilisateur

Emerson

Emerson Dixell XRi60CH Schéma de câblage

Emerson

Emerson Copeland XCM25D Mode d’emploi

Emerson

Emerson Branson 2000X ae Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur