Elsys AMPLIMAX EPRL16 Manuel utilisateur

AMPLIMAX

EPRL16

USER MANUAL

Maximum performance

for Internet in low or

nonexistent locations.

EASY

INTERNET

NANO

SIM

BEFORE USING

ATTENTION

TECHNICAL SPECIFICATIONS

To avoid physical and functional damage, do not open this device

beyond connections compartment. Prevent it from falls and / or

violent shocks. Always use its original font. Avoid using this

product or the devices connected to it during storms.

There is a risk of electric shock due to lightning strike.

BASIC REQUIREMENTS

• Network cable (RJ45) to connect Amplimax to POE – lenght depends on each installation.

• SIM Card nano (with active data plan).

This product has an active data collection function. For more information or deactivation,

refer to the item "Data Collection" in this manual.

Frequency band

Received level (mW)

Range (km)

850 MHz

Up to 200X more than the 3G / 4G USB modem

Up to 5X more than the 3G / 4G USB modem

Never insert the adapter that came with the product without the SIM card to avoid damaging the product's connector.

PLEASE NOTE: The source voltage for this product is 24 VDC. As this value is higher than that supported by most products on

the market, be careful not to connect it to other equipment, otherwise it will be damaged.

IMPORTANT

This product is

compatible with

the nano size

SIM card.

PLEASE NOTE:

Never insert or remove

the SIM card in the slot

with the device on. This

could damage it.

ABOUT THE RANGE OFTHIS PRODUCT

The range of AMPLIMAX depends on a number of factors, such as: frequency of operation, location and height of installation,

terrain profile, number and type of obstacles between the product and the cell tower, rain and reflections. Due to these factors

it is not possible to predict it accurately. Based on the experiences already made and published in the literature, we present

below an estimated comparison between two scenarios:

Scenario 1: USB modem connected indoors.

Scenario 2: AMPLIMAX ELSYS installed on the roof, at a height of 5 meters.

The table below describes the improvement in the range and level received fromAMPLIMAX in scenario 2 regarding to the

USB modem in scenario 1:

Supply voltage:

• 12 to 24VDC

Frequency Bands:

4G: 600*(B71), 700 (B12, B13, B14), 850(B5),

1700 (B4, B66), 1900 (B2) MHz

3G: 850 (B5), 1700 (B4) and 1900 (B2) MHz

Rate of data transmission:

• LTE R9: (DL) 70Mbps Max and (UL) 50Mbps Max

• HSPA R6: (DL) 21 Mbps Max and (UL) 5.76Mbps Max

• UMTS R99: (DL) 384kbps Max and (UL) 384kbps Max

MIMO 2x2 on the 4G downlink at the bands B4 and B66

Transmission power:

• Class 3 (24dBm + 1 / -3dB) for UMTS

• Class 3 (23dBm ± 2dB) for LTE

Operation temperature:

• External unit: 14°F ~ 140°F

• Power supply and POE: 32°F ~ 104°F

Storage temperature:

• -4°F ~ 158°F

Ethernet Port

• RJ45 connector

• IEEE 802.3 - Ethernet 10 / 100Mbps

Maximum length of RJ45 cable:

• With original source 24 VDC / 0.75A: 328ft

• With 12 VDC / 1.5 A source: 50ft

• With 12 VDC / 1.5 A battery: 50ft

Factory configured IP address

• 192.168.10.254

Main directional antenna

• 700 up to 2700 MHz

• Vertical polarization

• Gain:

700 to 960 MHz: 6 dBi 1710 to 1910 MHz: 7.9 dBi 1920 to 2700 MHz: 10 dBi

10 dBi (1920 MHz), 10 dBi (2310 MHz) and 8 dBi (2700 MHz)

Directional diversity antenna

• Bands: B4 and B66 (downlink)

• Horizontal polarization

• Gain: 8 dBi (2110 up to 2200 MHz)

Sim Card Slot

• Accepts nano Sim Card only

*Obs.: The band 600 MHz is the only one that is not covered by the product internal antenna. So, for that band,

the use an external antenna is mandatory.

1. Entrance to the SIM Card of the chosen carrier. Inserting untilyou feel a "click"

2. CELL NETWORK LED - Flashing, with time on longer than off, indicates connection established. Flashing, with off time longer

than on, indicates network search.

3. 4G LED - On indicates 4G connection. Off indicates 3G connection

4. RJ45 connection - for network cable up to 328 ft.

5. EASY INSTALL key - When pressed for 7 seconds, it performs the factory reset / Without the Sim Card it starts the blind

search / With the Sim Card it starts the signal location

6. Display (4 digits) - Displays equipment information

A. Connector for external antenna and LED indicator: Internal Antenna - LED off /External Antenna - LED on. Use only in

extreme cases and with cable up to 1.5m (max.).

B. Switching key between internal and external antenna.

WiFi

NOTEBOOK PC

B1 3 4 5 6

ANT EXT ANT

INT/EXT

RJ45/POE

SIM CARD

SIM CA RD

NANO

PRODUCT DETAILS

AMPLIMAX CONNECTIONS

POE INJECTOR CONNECTIONS

CELL

NETWORK EASY

INSTALL

POE CONNECTIONS

DC: Power supply 24V / 0.75A (dual voltage 100 ~ 240V).

POE: Network cable up to 100 m. Connects to AMPLIMAX.

LAN: Network cable to connect: PC, AP, Wi-Fi Router or Switch.

LED: Indicates source on and connected to the POE.

POE

LAN

POE

LED

POWER

SOURCE

AMPLIMAX

Preferably, the installation must be done according to the following steps:

NETWORK CABLE ASSEMBLY

Provide a network cable that will connect the POE to the AMPLIMAX, with direct assembly, that is, with the same two ends. If

the cable is passed through conduits, pass it before crimping its terminals. The use of good connectors and cable is essential

(it is recommended to use shielded CAT5e cable if the installation is external), especially since the cable also conducts the

product supply. The correct assembly of this cable is essential forthe proper functioning of the product and also to avoid

damaging it. For more information on cable assembly, check the Cable Assembly section in this manual. Use cable approved

by FCC, especially if the length is greater than 33 ft.

POE INSTALLATION

The POE must be installed indoors and connected to the source, computer, telephone and AMPLIMAX, as shown in the

diagram above.

INSTALLATION

Wi-Fi

The installation of AMPLIMAX must be done according to the simplified diagram below:

GENERAL CONNECTIONS MAP

The Sim Card

(nano) is installed

directly on the

AMPLIMAX.

100-240V

power supply

Use only a

cable of

NETWORK

RJ-45

(Ethernet)

ROUTER

SMARTPHONE

NOTEBOOK

PC OR

NOTEBOOK

POE

The product is not suitable for use in

domestic environments, as it may

cause electromagnetic interference

that requires the user to take the

necessary measures to minimize

these interferences.

To ensure better performance, it

is recommended to install

AMPLIMAX outdoors.

TABLET

If you want to know the cellular networks available at the installation site, perform the following steps:

Before mounting the reflector on the AMPLIMAX and before connecting the SIM Card, take the AMPLIMAX cabinet to a location

close to the final installation. Remove the AMPLIMAX cover and connect the network cable from the POE, as shown below:

POWER

SOURCE 24V NETWORK CABLE

RJ45 / Ethernet

ANT EXT ANT

INT/EXT

RJ45/POE

SIM CARD

POE

EASY INSTALL

BLIND SEARCH OF CARRIERS

Keep the product without

the SIM Card at this time

Hold it up so that

it can follow the

information on

the display.

As soon as the product is turned on, the display must

show the "Boot" ( ) message followed by "Load"

( ) and “---” Soon after, it displays the power of

supply that arrives at the product, which must be

greater than or equal to 9V ( ) Make sure that the

product is missing the SIM Card and wait for the

display show the message "nSIM" ( )

Then, press the “Easy Install" key, so that the equipment

starts the "Blind Search". Lift the product and hold it at

its bottom, so as not to impair the functioning of your

antenna, as shown in the figure on the side:

The "Blind Search" may take a few minutes, depending on the location and configuration of the product. At the end of this

period, the display will show the list of available cellular networks, organized by technology: (E.g.: 4G and 3G) and the level of

each one. (See list of networks in OPERATION). If no cellular networks are found, try searching elsewhere. The search will only

be performed on the technologies (4G and 3G) selected on the AMPLIMAX configuration web page. The factory setting will

search for 4G and 3G networks.

Once the "Blind search" has started, the process cannot be interrupted, and it must wait until the results obtained are

displayed. If you wish to interrupt the display of the Blind Search results, simply press the "Easy Install" key again.

Generally, the better the carrier level, the better the data rate. Keep in mind, however, that when the reflector is fitted and the

correct pointing is made, the level of the selected carrier tends to increase significantly.

Note: In some regions, an carrier that has a cellular network may rent its infrastructure to another carrier. In this way, the same

signal will be shared by the two carriers. In this case, the search will show only the carrier name that owns the cellular network.

CELL

NETWORK EASY

INSTALL

CELL

NETWORK EASY

INSTALL

CAUTION: To insert or remove the Sim Card, turn off the product or remove the network cable.

BEST SIGNAL FINDER

Once the carrier has been chosen and the reflector is correctly fitted, remove the AMPLIMAX cover and insert the SIM Card

in the correct position. Then reconnect the network cable from the POE, as shown according the figure.

As soon as the product is turned on, the display must show the message "Boot", followed by "Load", "- - - -" and the supply

voltage. If the product identifies a cellular network, it will display its name, followed by its band, signal level and technology in

a cyclical manner.

ANTENNA POINTING

FIT THE REFLECTOR TO THE CABINET (TOP TO BOTTOM)

SIM CARD POSITIONING

ANT EXT ANT

INT/EXT

RJ45/POE

SIM CARD

ANT EXT ANT

INT/EXT

RJ45/POE

SIM CARD

1 2 3

POE

Fit the reflector to the back

of the cabinet.

It must sliding like a drawer,

up to the limit of the path.

At the end, must activate

the lock with a "click".

The top view must appear as

in the figure below.

Attention to the

correct position

of the SIM Card

nano

NETWORK CABLE

RJ45 / Ethernet

Insert the card until the

end, when you feel a

"Click '

EASY

INSTALL

CELL

NETWORK

EASY

INSTALL

CELL

NETWORK

PRODUCT FASTENING

ON WALLS

ON MASTS

After the supply voltage disappears, press the “Easy Install" button, which will make the equipment indicate the level received

through the display in real time.

Note: When one carrier rents the cellular network from another, the display indicates the name of the proprietary network.

The value will be between 00 and 99%. In addition, there is an audible indication that is activated

at that time. The more continuous the sound, the stronger the signal. If AMPLIMAX is not yet

registered on the cellular network, the display will indicate the flashing message "BUSC.

Slowly rotate the AMPLIMAX pointing, trying to identify the angle that allows the best reception level. Vary it position, trying to

get away from possible obstacles. In general, the higher it is installed, the better the signal level.

Usually, a level above 30% already allows the use of the product. Even so, the higher the level received, the better it can be the

stability of your Internet. It is important to always seek the highest possible signal level.

Once the best position and pointing has been identified, just press the “Easy Install " key once to exit this mode.

The wall installation can be done with two screws for S6, S7 or S8 bushings. Fix the two screws on the wall 7.2 cm apart

(center-to-center), as the figure below:

When screwing the screws, leave a space of approximately

4 mm from the wall. Then, fit the AMPLIMAX to these

screws through the rear holes as in the figure:

The screws must

have a head of 0.9 to

1.0 cm in diameter

Prepare the mast with the template.

Then insert the clamps in the cabinet.

Prepare the mast with

the template. Then

insert the clamps in

the cabinet.

EASY

INSTALL

Curved guides

facilitate passage

of clamps

See drilling templates on the final page

Make sure your local network card is enabled to receive IP

automatically. The information below is for Windows 7:

• Select the Start / Control Panel / Network and Internet /

Network and Sharing Center / Change adapter settings option.

• With the right mouse button, select Local Connection

and go to Tools.

• Double click on "TCP / IP Protocol Version 4".

The screen on the side willbe displayed:

• Make sure that the "Obtain an IP address automatically"

option is enabled.

• Press OK and exit all screens.

Enter your browser and start using the Internet. Advanced

setting can be made through the product setting page, as

described in the item "WEB Setting Page".

VERIFYING THE INSTALLATION

Typically, the installation will be completed in this step. After energizing the product, wait 1 and a

half minutes. Check, then, that it is already possible to browse the Internet by connecting the

network cable (RJ-45) to a notebook, PC, Access Point or Wi-Fi router.

If you are unable to navigate, proceed to the next step.

(Only if necessary).

SETTING THE IP ON THE COMPUTER

OPERATION

OPERATING MODE

DISPLAY AND

WEB PAGE

Monitoring - With the inserted Sim Card it displays: carrier, band, signal level and technology.

Blind Search - Without the inserted Sim Card it displays: animation and audible signal until it search and displays the networks.

Signal Finder - With the Sim Card inserted, it displays the carrier's best signal level and audible signal.

Stand by - When it is not active, the display indicates "ON". The keys continue to function.

Network list

Received level and frequency band

Received level indication

Cellular technologies Messages

AT&T

DISPLAY

DISPLAYDISPLAY

Display

Technology (Mbps)

Carrier Description

Description

RECEIVED

LEVEL (%)

RECEIVED LEVEL

(dBm) RSSI-3G and 2G

Download up to 70 Mbps

Upload up to 50 Mbps No Sim Card (Sim Card)

HSPA +

Download up to 21.4 Mbps

Upload up to 5.7 Mbps

With Sim Card but without

registration Find forthe carrier

Band (MHz) in which the equipment is registered.

91 to 99%

61 to 90%

31 to 60%

0 to 30

> -70 dBm

-90 to-70 dBm

-100 to -91 dBm

<-100 dBm

RECEIVED LEVEL

(dBm) RSRP- 4G

> -90 dBm

-110 to -90 dBm

-120 to -11 dBm

< -120 dBm

QUALITY

EXCELLENT

GOOD

ACCEPTABLE

WEAK SIGNAL

Displays the current signal level, where XX is the percentage of the signal level.

This value varies between 00 and 99. The higher the value, the better the signal.

Unidentified level.

Searching for inserted

Sim Card network

Integrated Antenna enabled

Enabled External Antenna

Insert PIN on the LINK 4G

setting web page

Voltage at the RJ45 / POE

connector in Volts (Ex: 9 Volts)

HSUPA

Download up to 7.2 Mbps

Upload up to 5.7 Mbps

HSDPA

Download up to 7.2 Mbps

Upload up to 384 Kbps

Download up to 384 Kbps

Upload up to 384 Kbps

The received level signal is

indicated both on the

equipment's display and on

the web page. On the display,

it is indicated in percentage

and preceded by the letter

"n". On the AMPLIMAX

setting web page, the level is

indicated both in percentage

and in dBm. Levels above

30% are considered

sufficient, according to the

table on the side.

TMobile

Verizon

600

With the computer settings done correctly, open the browser of your choice and enter the IP address of the AMPLIMAX

(the factory default is 192.168.10.254). If all connections are correct, the product setting page can be accessed.

* If the automatic option does not work, make sure that the equipment is receiving some signal from the carrier.

AMPLIMAX HOME PAGE

Page with the basic settings of the Ethernet port and the 4G / 3G / 2G connection

FEATURED FEATURES:

BLIND SEARCH:

In the menu Tools is it is possible to do a BLIND SEARCH of carriers,

even with a Sim Card installed in the product. Find out which carrier is

performing best in your region.

BALANCE CONSULTATION:

Still on the menu Tools it is possible to receive and send SMS. This tool is

useful to check messages sent by the carrier and to make data inquiries.

Another tool that allows you to make balance inquiries is the "USSD",

which is also in the menu Tools.

DATA COLLECTION

In the menu About the Device it is possible to enable or disable data

collection, as well as to know its details.

The maximum cable length

must be 1.5m.

EXTERNAL ANTENNA

Although this product is integrated with a

high-performance Heptaband antenna, it

allows the installation of an external

antenna in a practical way in a TNC

connector, but there is an important detail

about the cable length.

To avoid signal loss, the external antenna

installation cable must not exceed 5ft.

Cellular connection

Antenna Type

Connection Type

Automatic Connection

Configured Ethernet

IP Address

Network Mask

Tools

General

Settings

System

Status

SIM: Carrier: Vivo Signal Level: 97% 4G Connection: UPDATE

Apply Changes

Internal

Automatic

192.168.10.254

255.255.255.0

To change the network mask of the Ethernet port

Call settings

Economy Mode

(Maximum speed 2MBPs)

Good

About

the device

WEB SETTING PAGE

System Status - On this page the user can see

all the equipment information.

To save press the “Apply Changes” key

To change the

IP address of

the Ethernet

port

To switch integrated

or external antenna.

To choose the mode

Turn on: Validate carriers

automatically.

Turn off: Manually select the carrier's

username, password and APN

Autres manuels pour AMPLIMAX EPRL16

Table des matières

Manuels Routeur sans fil populaires d'autres marques

Milesight

Milesight UG67 Manuel utilisateur

Airlogic

Airlogic AirSync Class 1 Manuel du propriétaire

Samsung

Samsung WCH730B Manuel utilisateur

TELEFONICA

TELEFONICA USB Adapter Manuel utilisateur

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuel utilisateur

Askey

Askey RAC2V1K Manuel utilisateur

Alloy

Alloy WLF2454AP-S Manuel utilisateur

TP-Link

TP-Link TL-WR542G Manuel utilisateur

NETGEAR

NETGEAR WNR2000v4 Manuel utilisateur

Hama

Hama 53120 Manuel utilisateur

Intellinet

Intellinet 524582 Manuel utilisateur

Asus

Asus RT-N10P Manuel utilisateur

D-Link

D-Link DIR-506L Manuel utilisateur

Sapido

Sapido GR297n Manuel utilisateur

Asus

Asus DSL-N55U Manuel utilisateur

AMTC

AMTC WR7502 Manuel utilisateur

Compaq

Compaq CP-2W - iPAQ Connection Point Manuel utilisateur

SMC Networks

SMC Networks WBR14-N2 FICHE Manuel utilisateur