Eloflex S1 Manuel utilisateur

INSTRUCTION MANUAL

FOR USE, DRIVING AND SAFETY

Read this documentation before using your Eloﬂex

to make sure that you use it in a manner that is safe, and which does not harm you,

your environment or your scooter.

Eloﬂex S1

Thanks and good luck!

Thank you for choosing an Eloﬂex as your power scooter. It means a lot to us because

our vision is to make people’s everyday life a little easier and to give people with disabilities

a greater freedom. We hope you experience both with the help of your Eloﬂex.

We believe that you will enjoy much of your new scooter. This manual contains

important information on safety, use and care. We encourage you to read through this

entire documentation before using your Eloﬂex for the ﬁrst time. We also suggest that

you train to run your Eloﬂex on a secluded, open and level surface before using it in other

contexts.

Eloﬂex scooter is designed for users with many different needs. Decide whether

Eloﬂex is suitable for the user is always taken by the ordinator or dealer together with the

user himself. Eloﬂex accepts no responsibility for cases where the scooter is not

adapted to the user’s needs.

An Eloﬂex should primarily be used in its standard design. If the scooter has to

be adapted or altered in any way, it must only be carried out by your assistant center or by

Eloﬂex. Please note that damages and faults caused by non-compliance with the operating

instructions or due to poor maintenance are not covered by the warranty.

Good luck and great joy with your Eloﬂex.

Drive carefully

Content Page

Intended use 3

Folding 4

Adjust seat length and seat height 5

Lift armrests 6

Anti-tip device 6

Manual driving 6

Remote key 7

Lights 7

Charging instructions 7

Control panel 8

Change seat width 9

Transport and storage 9

Error codes 10

Safety while driving 11

General safety information 13

Technical information 15

Contact 16

Type classiﬁcation and intended use

Eloﬂex power scooters have been developed for people

who have difﬁculty walking or cannot walk at all, but who

have vision ability, physical ability and mental ability to control

an scooter.

Eloﬂex Scooter is designed for outdoor use, but is compact

and ﬂexible enough for indoor use too. The chapter

”Technical data” at the back of this document contains

information on speed, turning radius, range, maximum lifting

capacity and maximum weight for the user and so on. We

encourage you to read all safety information in the chapter

”Safety” in this document.

Eloﬂex is tested and approved according to EN12184: 2014

- class B (indoor and outdoor use). Eloﬂex is also approved

according to ISO-7176, IEC60601 and the batteries are

approved according to UN38.3.

Eloﬂex power scooters meet the applicable requirements

of the MDR 2017/745.

Class 1 conformity assessment / CE marking has been

issued in accordance with Annex VIII Chapter III of MDR

2017/745. Conformity assessment procedure: Annex II and

Annex III of MDR 2017/745.The CE marking will be void if you

use replacement components or accessories that have not

been approved for this product.

Needs

The purpose of an Eloﬂex scooter is to compensate for an

injury or disability, which is why it is recommended in

the following circumstances:

• If the user has the inability to walk or very limited ability

to walk, which makes it difﬁcult to move in his / her own

home.

• If there is a need to leave the home to get out or to visit

places that are normally visited in order to carry out everyday

affairs.

• When the user has difﬁculty getting to, or performing work

or activities because of his / her mobility disabilities.

It is advisable to use Eloﬂex scooter both indoors

and outdoors, if it is not possible to use hand-operated

wheelchairs due to mobility problems, but it is still possible to

properly handle a scooter.

Accessories

Chargers and bag with simpler tools are available when

delivered in the storage bag under the seat.

Utility

Only use the Eloﬂex scooter when fully functional.

Otherwise you put yourself and others at risk. The following

list does not include all possible situations. It describes only

certain situations that may affect the usability of the scooter.

• Do not use the scooter if the batteries are defective or

deformed

• Do not use the scooterif the engine is jerky or

makes abnormal noise

• Do not use the scooter if the brake function

appears to be wrong

• If your tires are worn, contact your assistant center or

dealer

• If you notice any damage to the seat belt, armrest, seat,

backrest, handlebar or other part of the scooter, contact your

assistant center or dealer.

• If you notice any damage to the electrical system (cables,

batteries, chargers, etc.), please contact your assistant

center or dealer.

Warranty

You always have a two-year warranty on your Eloﬂex scooter.

The warranty conditions are in line with the applicable national

and general terms and conditions and rules

and regulations. The detailed warranty conditions can be

downloaded at www.eloﬂex.eu. Note that you should save

the original carton for your Eloﬂex during the warranty period

(the carton can be folded together and set aside)

Life span

The estimated lifetime of an Eloﬂex is 5 years. However, the

life of the product is largely affected by how it is used and

managed. An Eloﬂex can have a much longer life if you take

care of it in a good way and only use it in line with the

information in this document.

Safety regulations and risks

PLEASE READ THE SAFETY INSTRUCTIONS FROM THE

PAGE 11 BEFORE YOU USE YOUR ELOFLEX.

Intended use

Folding

Fold up

Step 1

Lay the folded scooter on the ground

as shown on the right. Fold up the

handlebar by lifting it up and forward.

Then lock the handlebar with the help

of the clamp that is in the hinge in the

bottom of the handlebar. To secure the

clamp, turn the black plastic fuse over

the clamp.

Collapse

Step 1

Open the locking hook as shown in the

picture to the right.

Step 2

Put one hand on the front edge of the

handlebars. Grasp the top edge of the

backrest with the other hand and fold it

forward. Fold the scooter according to

the pictures to the right.

Step 2

Grasp the backrest and pull upwards to

open the chair. Hold with one hand on

the handlebars.

It is very important

that you close the

locking hook before

using the scooter.

Step 3

Close the locking hook on the back

of the scooter - this is very important!

Make sure the locking hook clicks in.

Step 3

Open the locking clamp on the bottom

of the handlebar by turning off the

safety hook and opening the hook.

Then fold down the handlebars and

place it on top of the folded seat.

Adjust seat length and seat height

Increase seat length

Make sure that the scooter is in the driving

position and is switched on. Press and

hold the up arrow to expand the scooter.

Adjust seat height

Remove the scooter’s seat cushion. Pull

the black wire under the front edge of the

seat. At the same time as the wire is kept

in the tensioned position, the rear edge

of the seat can now be adjusted to the

desired position (three different positions).

When the seat is in the desired position,

the front edge of the seat is placed at the

same level as the rear edge. Release the

cable to lock the seat in the hole that is at

the same level as the rear edge.

Shorten seat length

Make sure that the scooter is in the driving

position and is switched on.

Press and hold the down arrow to reduce

the distance between the seat and the

handlebar.

Lift armrests

To lift the armrests up and down, ﬁrst

loosen the lock by turning the locking

lever half a turn. Then lift the armrests.

The anti-tip devices have two positions.

One for driving position and one for

when the scooter is set in a standing

position during storage. You can

easily change the position by manually

adjusting the anti-tip devices.

NOTE! The anti-tip devices must

always be in their driving position (as

in the picture) when the scooter is

used.

Turn off the scooter. Then push the

red levers on the motors (see picture)

to disconnect the magnetic brakes. In

this position, the scooter can be rolled

manually.

Note! If the scooter has to be moved

when turned off, the magnetic lock of

must always be switched off.

Manual driving

Anti-tip device

IMPORTANT!

NEVER kick on the red

levers with your foot.

Only use your hands.

It is important

that you lock

the armrests

when you fold

them down again by turning

the lock lever back half a

turn. LOCKEDOPEN

OFF

IMPORTANT!

NEVER connect the

charger directly to

the battery.

This is how you charge

Start by turning off your Eloﬂex.

Connect the charger to the socket on

front of the handlebar. Make sure that

the contacts’ position matches each

other. Then plug the charger’s power

cable into a wall outlet. Charging is

indicated by a lamp on the charger.

Red lamp means that charging is in

progress. After about three hours, the

batteries are charged at 90 percent.

The scooter can now be used again.

After about 5-8 hours, the light on

the charger becomes green and the

batteries are fully charged. During

charging, the charger itself becomes

warm, and this is normal. For maximum

battery life, charging should take place

for about ﬁve hours when the bar on

Charging instructions

the battery indicator has dropped to

one third. The batteries will not be

damaged by maintenance charges

but for maximum battery lifespan we

recommend that you disconnect the

charger when the batteries are fully

charged.

Charging the batteries can be done

down to -10 degrees. When charging

in lower temperatures, the batteries will

not get fully charged. If your Eloﬂex is

used in minus degrees, the mileage is

affected. For example, at -10 degrees,

the mileage can be reduced by up to

50%.

Remote key

Your Eloﬂex scooter is delivered with a

remote control key. The remote control key

can be used to lock/unlock your scooter.

When the scooter is in the locked position,

it is not possible to drive it.

Your Eloﬂex scooter has front and rear

lighting for increased safety. To turn on the

lights, tap the light icon on the left side of

the handlebar. There are also brake lights

and turn signals. Use the turn signals

with the two arrows on the left side of the

handlebars. The brake light is activated

when the scooter is stationary, when you

release the throttle and when braking with

the brake button.

Lights

Increase seat length

Neutral seat length

Shorten seat length

Increase speed

Decrease speed

On and off button

Control Panel

Information display: The display on the

scooter has 2 different display modes, one

showing current information about speed,

gear selection, headlights and turn signals.

The other display mode lights up in the event

of a fault on the scooter. The current error

code, battery voltage and current gear are

displayed there.

Turn signal left Turn signal right

Lights

Horn

Break

Reverse

Accelerator

Battery control: This indicates how much

power is left in the batteries. When the

batteries are fully charged, all the lights are

on. As the batteries discharges, the lights go

out one at a time. Charge when two thirds of

the lights has gone out.

Driving instructions

To start

When you start the scooter (on and off

button) it is in parking mode. Then press

the red brake button and then you can start

driving with the gray acceleratior button.

To reverse

You push the gray button under the battery control indicator to

change into reverse mode. A beeping sound is heard when

the reverse mode is on (you also see which driving mode that

is on at the scooter’s display). You then reverse by pressing

the accelerator button. When you want to drive forward again,

click on the gray button again to change back into driving

mode.

You can increase the seat width by

moving out the armrests using the widening kit.

You can choose to increase

the seat width by 5 or 10 cm.

Step 1

Loosen the armrests on each side by

unscrewing its two brackets.

Step 2

Fit the widening sleeve between the

chair and the armrest. Reinstall the

armrests.

Change the seat width

You order the widening kit from the reseller from where you bought your scooter.

Transport and storage

• A folded scooter can be placed in the luggage of a larger car. Use ramps to get the

scooter into the car.

• A folded scooter can stand upright as in the picture to the right to take up less space.

• If the scooter is not to be used for a while, we recommend that the batteries be fully

charged before putting the scooter away.

• The scooter should be stored indoors in frost-free, dry and ventilated areas. Storage

temperature on 0-30 degrees is recommended.

• When transporting by bus or by handicap transportation, the Eloﬂex must be attached to

the fastening points shown in the pictures at the bottom. Note that Eloﬂex is not tested as

a car seat. We therefore always recommend that the user moves over to the car’s own

seats.

Error Codes

Error codes that may appear on the display

ERROR CODE CAUSE FIX THE ERROR

Left/Right

solenoid fault

1. The magnetic brake of the left / right

motor is open.

2. Connection fault on the left motor’s

magnetic brake.

3. The magnetic brake of the left motor

is broken, or the control unit may be

damaged.

1. Close the magnetic brake by pulling the

red handle to the closed position.

2. Verify that the motor connector is properly

connected.

3. Contact your reseller for assistance.

Left/Right

Overcurrent

1. Overvoltage due to too much

resistance.

2. Engine or control unit fault.

1. The system resets when the resistance is

gone.

2. Kontakta din återförsäljare för hjälp.

Acceleration not

zero

1. The throttle handle is not in the ”zero

position” when the chair performs a start-

up test.

2. Control unit fault.

1. Release the throttle and restart the scooter.

2. Contact your reseller for assistance.

Acceleration fault Fault in throttle handle or control unit. Contact your reseller for assistance.

MController not

support

Fault in control unit, or wrong type of

control unit.

Change control unit.

Com fault Dis to

1. Loose or incorrectly installed

connections.

2. Control unit fault.

1. Verify that all connections are properly

installed.

2. Contact your reseller for assistance.

Left/Right driver

fault

Control unit fault. Contact your reseller for assistance.

Push rod Fault Short circuit in the length adjustment

motor, broken length adjustment motor or

fault in control unit.

Check the connection to the length

adjustment motor, or contact your reseller for

assistance.

Battery vol too high Wrong battery type or broken battery. Replace the 24V battery.

Battery vol too low The battery is old or uncharged. Charge the battery or replace it if it is old.

Angle sensor fault Angle sensor is broken or connection fault. Contact your reseller for assistance.

Table des matières

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur