ElmoTech SBU2000 Mode d'emploi

SBU2000

Installation and Operation Guide

Information in this documentation is subject to change without notice

and does not represent a commitment on part of Elmo-Tech Ltd. The

software described in this document is subject to the license agreement

that is included with the product, which specifies the permitted and

prohibited uses of the product. Any unauthori ed duplication or use of

this documentation, in whole or in part, in print, or in any other storage

or retrieval system is prohibited.

No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system, or translated into any language in any form

by any means for any purpose other than the purchaser’s personal use

without the permission of Elmo-Tech Ltd.

Unless otherwise noted, all names of companies, products, street

addresses, and persons contained herein are part of a completely

fictitious scenario and are designed solely to document the use of an

Elmo-Tech product.

Corporate Headquarters

Elmo-Tech Ltd.

2 Ha-Bar el St.,

P.O. Box 13236,

61132 Tel Aviv, Israel

Tel: 972-3-7671800

Fax: 972-3-7671801

U.S.A Customers, call 1-800-313-1483

E-mail: contact@elmotech.com

Visit us at: www.elmotech.com

Table of Contents

Installation Instructions for the Electronic

Monitorin System

1. SBU2000 Monitorin Unit Placement

In order to install the Electronic Monitoring System, you will need to find the best

location for the SBU2000 Monitoring Unit. The ideal location for the SBU2000

Monitoring Unit is as close as possible to the center of the house.

The SBU2000 Monitoring Unit should be placed on a flat hori ontal surface, at

least 3 feet off the ground and at least 1 foot away from the wall. The SBU2000

Monitoring Unit should be in an open area away from other electrical appliances,

personal computers, laptops or metal objects.

2. Installin the SBU2000 Monitorin Unit

In order to install the SBU2000 Monitoring Unit, perform the following steps:

1. Disconnect the telephone cord from the wall telephone socket and plug it into

the Phone socket, located on the rear panel of the SBU2000 Monitoring Unit.

2. Connect one end of the supplied telephone cord into the Line socket, located

on the rear panel of the SBU2000 Monitoring Unit, and then connect the other

end of the same cord into the wall telephone socket.

3. Connect the appropriate end of the power adapter cord into the Power socket

located on the rear panel of the SBU2000 Monitoring Unit.

4. Connect the power adapter into a wall power socket. The SBU2000

Monitoring Unit makes an audible beeping sound and then runs through a

series of initialisation tests to check that everything is in order.

5. After completing the initialisation tests successfully the SBU2000 Monitoring

Unit beeps again and the left and right external LED indicators, located on the

rear panel of the SBU2000 Monitoring Unit are turned on. This indicates that

the SBU2000 Monitoring Unit is in a working state and has automatically

switched to standby mode.

3. Installin the 2TRACK

Installing the 2TRACK system involves:

1. Collecting the appropriate installation equipment and tools

2. Verifying that the Offender is registered in the E3-MWS software

3. Activating the 2TRACK Tracker unit

a. Installation Equipment

The kit of installation equipment includes the following items:

1. Tracker unit with carrying pouch and power adapter

2. Transmitter with strap holder

3. Locking clips

Warning: The Tracker unit’s battery must be

fully charged.

Verify the battery’s status by plugging the

charger into the Tracker unit and removing it.

The Tracker unit’s screen displays a power bar

to indicate the charge level of the battery.

b. Installation Tools

You will also need the following installation tools:

1. Manual Reset Device (MRD) – for activating the Transmitter

2. Strap locking tool – for locking the Transmitter

3. 0.2” (5mm) flat head screwdriver – for opening the locking clip

4. Snake eye screwdriver – for changing the straps of the Transmitter

c. Offender Information in the E3-MWS

Verify the following Offender details in the E3-MWS software application:

1. Offender’s name and address

2. Offender’s program type – 2TRACK Active

3. Equipment serial numbers – these must match the serial numbers on

the equipment you are planning to activate:

a. Tracker unit serial number

b. Transmitter serial number

Note: The relevant serial numbers are visible

on the back or side of each equipment item.

 Tracker unit SIM card details

For more information about working with the E3-MWS system, refer to the E3-

MWS Monitor Operator’s Manual.

4. Place 2TRACK in SBU2000 Unit

The SBU2000 unit device used to recharge the 2TRACK and transmit all GPS

location information, violation information, and house arrest status. It also

monitors the Ankle Bracelet when the 2TRACK is placed in the base unit

(docked).

5. Installation Manual for bracelet unit

Bracelet

To Attach the Bracelet

1. Match the Bracelet serial number on the Bracelet case to the number on

the Bracelet serial number in the hardware list in PCE. The ankle

transmitter and strap will be shipped unattached. You must insert one end

of the strap into the transmitter and push the locking pins into place. Make

sure that the locking pins are flush with the case. Measure the strap to the

offender’s leg and cut the strap to fit around the offender’s ankle. You

should si e the strap so that it allows approximately ¼ inch of space

between the offender’s leg and the strap to ensure comfort.

2. Once you have the strap attached, push the locking pin through the holes

on the bracelet and into the strap until it locks into place

3. Make sure the locking pin is pushed far enough so that the top of the pin is

flush with the bracelet case

To Remove the Bracelet

1. Cut the strap

2. Using the screwdriver provided, turn the right locking pin counter

clockwise and the left locking pin clockwise to remove

3. Lift each side of the pin up from the strap and remove. Slide both ends of

the strap out of its channel. Dispose of the strap

4. Clean the bracelet with mild detergent. Rinse, dry, and return to your

inventory.

Downloading the Curfew Schedule

Once the monitoring system has been installed, perform the following:

1. Verify that the right LED located on the rear panel of the SBU2000

Monitoring Unit is constantly on and not flashing.

2. Using a mobile phone, call the monitoring center personnel and ask them to

perform a manual download.

Table des matières

Autres manuels ElmoTech Instrument de mesure

ElmoTech

ElmoTech SBU2000 Mode d'emploi

ElmoTech

ElmoTech MEMS 3000 Manuel utilisateur

ElmoTech

ElmoTech MU-800-2 Guide de démarrage rapide

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur