Elkay OBFAVRFRD Manuel d'installation
97571C (Rev. E - 11/04)
OBFAVRFRD
Page 1
Installation, Care & Use Manual
FIG. 1
7
18
32
5
21
27 SEE FIG. 6
31
19
28
17
26,29
23, 24, 25
36
6
933 38 9
37
OBFAVRFRD
Page 2
97571C (Rev. E - 11/04)
FIG. 2 *ADAREQUIREMENT
LEGEND
A=RECOMMENDEDWATERSUPPLYLOCATION 3/8O.D.UNPLATEDCOPPERTUBECONNECT STUB1-1/2IN.(38mm)OUT FROMWALLSHUTOFF BYOTHERS
B=RECOMMENDED LOCATIONFORWASTE OUTLET1-1/4”O.D. DRAIN
C=1-1/4TRAPNOTFURNISHED**
D=ELECTRICALSUPPLY(3) WIRERECESSEDBOX
E=INSURE PROPER VENTILATIONBYMAINTAINING6"(152 mm)(MIN.)CLEARANCEFROM CABINET LOUVERSTOWALL.
F=7/16 BOLTHOLESFORFASTENINGUNITTOWALL
FINISHEDFLOOR
97571C (Rev. E - 11/04)
OBFAVRFRD
Page 3
IMPORTANT
ALLSERVICE TOBE PERFORMEDBY AN AUTHORIZED SERVICE PERSON
HANGERBRACKETSANDTRAPINSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
y7-3/4 in. (197mm) dimension from wall to centerline of trap must be maintained for proper fit.
yAnchor hanger securely to wall using all six 1/4 in. dia. mounting holes.
3) Install straight valve for 3/8" O.D. tube. INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is engaged properly in the slots on the cooler back.
5) Loosen the two screws holding the lower front panel at the bottom of cooler base. Pull front panel forward to gain access
inside cooler.
6) Connect water inlet line - See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler water line making sure that the end of the
waste line fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 15 by
using a small screwdriver through the small hole in the push button item 2 (See Fig.3). Clockwise adjustment will raise
stream and counter-clockwise adjustment will lower stream. For best adjustment stream should hit basin approximately
6-1/2" (165mm) from bubbler.
PROTECTFROMHARD FREEZING
9) If the ambient air temperature drops below 0° F, the cooler needs to be drained of all water by blowing out all water lines
and the drain trap.
FIG. 3
34 8
13 14
15
10
2
34
20 930 10
35
1
16
OBFAVRFRD
Page 4
97571C (Rev. E - 11/04)
PRINTED IN U.S.A.
PARTS LIST
PART NO
22897C
45662C
75672C
45663C
35906C
35907C
35909C
56033C
75500C
70864C
27469C
75566C
40045C
15005C
61313C
50986C
75532C
35900C
38417001
27295C
55996C
98118C
40614C
50400C
50401C
70444C
21903C
27306C
70016C
55931C
15009C
56092C
26999C
22814C
22822C
22854C
22862C
22955C
100322740560
400660943730
75519C
75520C
75674C
Panel - Bottom Dispenser
Button - Push
Screw - Cap
Sleeve - Push Button
Heater Strip
Switch - Rocker
Heater Thermostat Assy
Washer
Screw - Torx
Screw - #8 x 5/8” Lg. Torx/Slot
Panel - Screen
Screw - Torx
Hex Nut
Retaining - Nut
Regulator
Holder - Regulator
Screw
Power Cord
Screw - #8-18 x 3/8” HHSM
Panel - Front Dispenser
Strainer
Bubbler Assembly
DrainTube
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Basin - Stainless Steel
Adaptor - Basin
Hex Nut #10-32
Cover-Dispenser Bottom Gray
Bubbler - Nipple
Poly Tubing (Cut To Length)
Cover - Bottom
Panel - LH No Push
Panel-RH No Push
Panel - LH Rear
Panel-RH Rear
Panel - Front Lower
Gasket
Hanger Bracket
Bit - Pinned Torx T-15
Bit - Pinned Torx T-25
Wrench - Allen 7/64
ITEM
NO DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
NS
NS
NS
NS
NOTE: All correspondence pertaining to any of the above water
coolers or orders for repair parts MUST include Model No. and
Serial No. of cooler, name and part number of replacement part.
WARNING!
This unit is frost resistant down to 0° F with no wind. Prevail-
ing winds can reduce the ability of the heater element to
preventlightfreezing. If the ambient air temperaturewilldrop
below 0° F, the cooler needs to be drained of all water by
blowing out all water lines and the drain trap.Aheater strip
is used to heat the unit and will begin to cycle at 40° +/- 5°
F. Acheck at this temperature will ensure the heater is
working and the unit is resistant to light freezing.
ALSO,MAKE SURE THERE ARENO PLASTIC OR
FLAMMABLECOMPONENTS DIRECTLYABOVETHE
HEATER STRIP.
FIG. 5
12
12
11
FIG.4
FIG. 6
22
39
31
www.DrinkingFountainDoctor.com 800-518-5388
Table des matières
Autres manuels Elkay Congélateur
Elkay
Elkay ESRC8 1E Series Manuel d'installation
Elkay
Elkay FD700DL Manuel utilisateur
Elkay
Elkay EZFTL8 1E Series Manuel d'installation
Elkay
Elkay LFAE8TF1Z Manuel utilisateur
Elkay
Elkay EWTLA Series Manuel d'installation
Elkay
Elkay EFOA8T1Z Manuel utilisateur
Elkay
Elkay LVRCHDTL8SC Manuel utilisateur
Elkay
Elkay LFAE8SF1Z Manuel utilisateur
Elkay
Elkay LFAE14L1Z Manuel utilisateur
Elkay
Elkay FD7003*F2YJO Series Manuel d'installation
Elkay
Elkay LFAE8LF1Z Manuel utilisateur
Elkay
Elkay Flexi-Guard EZ Series Manuel d'installation
Elkay
Elkay LFAE20SF1Y Manuel utilisateur
Elkay
Elkay LVRCHDTLDDSC Manuel utilisateur
Elkay
Elkay OBFAVR8 1D Series Manuel d'installation
Elkay
Elkay EL Series Manuel d'installation
Elkay
Elkay EFOA8S1Z Manuel utilisateur
Elkay
Elkay LFAE14SF1Z Manuel utilisateur
Elkay
Elkay LZS8WSS2K Mode d’emploi
Elkay
Elkay EFRCM8K Manuel utilisateur
