Eliwell ICPlus 902 Manuel utilisateur
ICPlus 902
Electronic controller with 1 intervention point
EN
USER INTERFACE
ICPlus 902
KEYS
UP
Press and release
Scroll menu items
Increases values
Press for at least 5 sec
Function can be configured by the user (H31)
STAND-BY (ESC)
Press and release
Returns to the previous menu level
Confirms parameter value
Press for at least 5 sec
Function can be configured by the user (H33)
DOWN
Press and release
Scroll menu items
Decrease values
Press for at least 5 sec
Function can be configured by the user (H32)
SET (ENTER)
Press and release
Displays alarms (if active)
Opens Machine Status menu
Confirm commands
Press for at least 5 sec
Opens Programming menu
ICONs
Decimal Point Temperature
Permanently on: decimal point Permanently on: displays a temperature
Flashing: Soft Start active Flashing: reduced set active, displays
a temperature or no unit of
measure selected
Off: otherwise
Pressure Humidity
Permanently on: displays a pressure Permanently on: displays a humidity
Flashing: reduced set active and displays
a pressure
Flashing: reduced set active and displays
a humidity
Relay OUT1 Not Used
Permanently on: OUT1 output active
Flashing: a delay, a protection or a locked
start-up
Off: otherwise
Alarm NOTE:
When switched on, the device performs a Lamp Test; the
display and LEDs will flash for several seconds to check that
they all function correctly.
Permanently on: alarm active
Flashing: alarm acknowledged
Off: otherwise
NTC/PTC MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
NTC: -50...110°C (-58...230°F)
PTC: -50...140°C (-58...302°F)
on display with 3½ digits + sign
Analogue input 1 NTC or 1 PTC
(selectable by parameter H00)
Serial TTL for connection to Copy Card or
Televis/Modbus remote control systems
Digital outputs OUT1: 1 SPDT relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -50 ... 140°C (-58 ... 284°F)
Accuracy better than 0.5% of end of scale +1 digit
Resolution 0.1°C (0.1°F up to +199.9°F; 1°F over)
NTC/PTC - 12V, 12-24V
Supply
Pb1
OUT1
1 2 3 8 9 10 11
NTC/PTC - 24V, 115V, 230V
Supply
Pb1
OUT1
1 2 3 4 5 10 11
TERMINALS
1-2 N.C. regulator relay OUT1 *4-5 Power supply 24Va, 115Vaand 230Va.
1-3 N.O. regulator relay OUT1 *8-9 Power supply 12Va/c and 12-24Va/12-36Vc.
10-11 Probe Pb1 Input
ATTL input for Copy Card and TelevisSystem connection * depends on model
NTC/PTC MODEL (with 2HP relay)
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
NTC: -50...110°C (-58...230°F)
PTC: -50...140°C (-58...302°F)
on display with 3½ digits + sign
Analogue input 1 NTC or 1 PTC
(selectable by parameter H00)
Serial TTL for connection to Copy Card or
Televis/Modbus remote control systems
Digital outputs OUT1: 1 SPST relay 16(8)A 2Hp 250 Va
Buzzer output only on models where this is provided
Measurement range -50 ... 140°C (-58 ... 284°F)
Accuracy better than 0.5% of end of scale +1 digit
Resolution 0.1°C (0.1°F up to +199.9°F; 1°F over)
NTC/PTC - 12V (2 Hp)
Supply
Pb1
OUT1
4 5 7 8 9 10 11
NTC/PTC - 230V (2 Hp)
Supply
Pb1
OUT1
4 5 76 9 10 11
TERMINALS
4-5 N.O. regulator relay OUT1 *6-7 Power supply 24Va, 115Vaand 230Va.
9-11 Probe Pb1 Input *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.
ATTL input for Copy Card and TelevisSystem connection * depends on model
V/I MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
-199...199 (ndt = n)
-199.9...199.9 (ndt = y)
-1999...1999 (ndt = int)
on display with 3½ digits + sign
Analogue input
1 V/I (0-1V, 0-5V, 0-10V, 0...20mA, 4...20mA)
(selectable by parameter H00)
Maximum load: - current = 100 Ω
- voltage = 20 kΩ
Serial TTL for connection to Copy Card or
Televis/Modbus remote control systems
Digital outputs OUT1: 1 SPDT relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -1999 ... 1999
Accuracy better than 0.5% of end of scale +1 digit
Resolution 1 or 0.1 digit according to settings
V/I - 12V, 12-24V
+12V
I
V
+ +−
Supply
OUT1
1 2 3 7 8 9 10 11 12
V/I - 24V, 115V, 230V
+12V
I
V
+ +−
Supply
OUT1
1 2 3 76 9 10 11 12
TERMINALS
1-2 N.O. regulator relay OUT1 *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.
1-3 N.C. regulator relay OUT1 *9-10-12 Voltage input (9=GND; 10=”+”; 12=12V)
*6-7 Power supply 24Va, 115Vaand 230Va.*9-11-12 Current input (9=GND; 11=”+”; 12=12V)
ATTL input for Copy Card and TelevisSystem connection * depends on model
PT100/Tcj-Tck MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
PT100: -150...650°C
TcJ: -40...750°C
TcK: -40...1350°C
on display with 3½ digits + sign
Analogue input 1 PT100 or 1 TcJ / Tck
(selectable by parameter H00)
Serial TTL for connection to Copy Card or
Televis/Modbus remote control systems
Digital outputs OUT1: 1 SPDT relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -150 ... 1350°C (-238 ... 2462°F)
Accuracy see ‘Pt100/TcJ/TcK models’ table
Resolution see ‘Pt100/TcJ/TcK models’ table
PT100/Tcj-Tck - 12V, 12-24V
Supply
Pb1
+−
1 2 3 6 7 10 11 12
OUT1
PT100/Tcj-Tck - 24V, 115V, 230V
Supply
Pb1
+−
1 2 3 65 10 11 12
OUT1
TERMINALS
1-2 N.O. regulator relay OUT1 *6-7 Power supply 12Va/c and 12-24Va/12-36Vc.
1-3 N.C. regulator relay OUT1 *10-11-12 Probe PT100 input - 3 wires (Pb1)
*5-6 Power supply 24Va, 115Vaand 230Va.*11-12 TcJ/TcK input
ATTL input for Copy Card and TelevisSystem connection * depends on model
PT100/Tcj-Tck MODELs
PT100: ACCURACY: 0.5% for whole scale + 1 digit
0.2% from -150 to 300°C
RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
TcJ: ACCURACY: 0.4% for whole scale + 1 digit
RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
Tck: ACCURACY: 0.5% for whole scale + 1 digit
0.3% from -40 to 800°C
RESOLUTION: 0.1°C (0,1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
MOUNTING - DIMENSIONS
The device is designed for panel mounting. Drill a 29x71 mm hole and insert the instrument; secure it with the special brackets provided. Do not
install the instrument in damp and/or dirty places; in fact, it is suitable for use in places with ordinary or normal levels of pollution.
Keep the area around the instrument cooling slots adequately ventilated.
74 mm
32 mm
29 mm
71 mm
70 mm
59 mm
EWPA-EWHS PROBE CONFIGURATION
EWPA 007/030 2 wires / Transducer
Transducer
brown
white
9101112
EWHS 304/314 3 wires
Probe
GND (only EWHS314)
V+
RH/T
9101112
EWHS 284 2 wires
Probe
brown
blue
9101112
EWHS 314 4 wires (V-I model)
Probe
GND
V+
RH
T
GND
ICPlus
1I
CPlus 2
91011129101112
USING THE COPY CARD
The Copy Card is connected to the serial port (TTL) and allows rapid programming of the instrument parameters. Access Installer parameters by
entering ‘PA2’, scroll through the folders using and until folder FPr appears. Select it using , scroll through the parameters using
and , then select the function using (eg. UL).
• Upload (UL): Select UL and press . This function uploads the programming parameters from the instrument to the card. If the
procedure is a success, ‘y’, will appear on the display, otherwise ‘n’ will appear.
• Format (Fr): This command is used to format the copy card (recommended when using the card for the first time).
Important: the Fr parameter deletes all data present.This operation cannot be cancelled.
• Download:Connect the Copy Card when the instrument is switched off. At power-on, data is downloaded from the copy card to the
instrument automatically. At the end of the lamp test, the display will show ‘dLy’ if the operation was successful and ‘dLn’
if not.
UPLOAD
DOWNLOAD
OR
NOTE: After downloading, the instrument works with the settings of the new map just downloaded.
Table des matières
Autres manuels Eliwell Contrôleurs
Eliwell
Eliwell EZ-HT Manuel utilisateur
Eliwell
Eliwell ECH 200BD "Adaptive" Manuel utilisateur
Eliwell
Eliwell IDplus 902 Manuel utilisateur
Eliwell
Eliwell EWPC 961/S Manuel utilisateur
Eliwell
Eliwell EWDB 111 Manuel utilisateur
Eliwell
Eliwell ID 974 Manuel utilisateur
Eliwell
Eliwell ID 970 Manuel utilisateur
Eliwell
Eliwell ID 961 Manuel utilisateur
Eliwell
Eliwell 210 L Series Manuel utilisateur
Eliwell
Eliwell IC 912 Pt100-TC Manuel utilisateur
Eliwell
Eliwell IWP 740 Manuel utilisateur
Eliwell
Eliwell RGF 312 Manuel utilisateur
Eliwell
Eliwell EWHT 1800LX Manuel utilisateur
Eliwell
Eliwell FREE Panel EVP 3300/C Manuel utilisateur
Eliwell
Eliwell IC 912 LX Pt100 R Manuel utilisateur
Eliwell
Eliwell EW961 Manuel utilisateur
Eliwell
Eliwell EWRC 500 NT Series Manuel utilisateur
Eliwell
Eliwell ID 971 Manuel utilisateur
Eliwell
Eliwell EWPlus 971 Manuel utilisateur
Eliwell
Eliwell EWPlus 902 Manuel utilisateur
