Eliwell ICPlus 915 Manuel utilisateur
ICPlus 915
Electronic controller with 2 intervention points
EN
USER INTERFACE
ICPlus 915
KEYS
UP
Press and release
Scroll menu items
Increases values
Press for at least 5 sec
Function can be configured by the user (H31)
STAND-BY (ESC)
Press and release
Returns to the previous menu level
Confirms parameter value
Press for at least 5 sec
Function can be configured by the user (H33)
DOWN
Press and release
Scroll menu items
Decrease values
Press for at least 5 sec
Function can be configured by the user (H32)
SET (ENTER)
Press and release
Displays alarms (if active)
Opens Machine Status menu
Confirm commands
Press for at least 5 sec
Opens Programming menu
ICONs
Decimal Point Temperature
Permanently on: decimal point Permanently on: displays a temperature
Flashing: Soft Start active Flashing: reduced set active, displays
a temperature or no unit of
measure selected
Off: otherwise
Pressure Humidity
Permanently on: displays a pressure Permanently on: displays a humidity
Flashing: reduced set active and displays
a pressure
Flashing: reduced set active and displays
a humidity
Relay OUT1 Relay OUT2
Permanently on: OUT1 output active Permanently on: OUT2 output active
Flashing: a delay, a protection or a locked
start-up
Flashing: a delay, a protection or a locked
start-up
Off: otherwise Off: otherwise
Alarm NOTE:
When switched on, the device performs a Lamp Test; the
display and LEDs will flash for several seconds to check that
they all function correctly.
Permanently on: alarm active
Flashing: alarm acknowledged
Off: otherwise
NTC/PTC MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
NTC: -50...110°C (-58...230°F)
PTC: -50...140°C (-58...302°F)
on display with 3½ digits + sign
Digital input 1 digital voltage free input
Analogue input 1 NTC or 1 PTC
(selectable by parameter H00)
Serial TTL for connection to Copy Card or Televis/
Modbus remote control systems
Digital outputs OUT1: 1 SPDTrelay 8(4)A250Va
OUT2: 1 SPST relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -50 ... 140°C (-58 ...284°F)
Accuracy better than 0.5% of end of scale +1 digit
Resolution 0.1°C (0.1°F up to +199.9°F; 1°F over)
NTC/PTC - 12V, 12-24V
D.I.
Supply
Pb1
OUT1 OUT2
1 2 3 4 5 7 8 9 10 11 12
NTC/PTC - 24V, 115 V, 230 V
D.I.
Supply
Pb1
OUT1 OUT2
1 2 3 4 5 6 7 9 10 11 12
TERMINALS
1-2-3 regulator relay OUT1 *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.
4-5 regulator relay OUT2 9-11 Probe Pb1 Input
*6-7 Power supply 24Va, 115Vaand 230Va.9-12 Digital Input (D.I.)
ATTL input for Copy Card and TelevisSystem connection * depends on model
V/I MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
-199...199 (ndt = n)
-199.9...199.9 (ndt = y)
-1999...1999 (ndt = int)
on display with 3½ digits + sign
Digital input 1 digital voltage free input
Analogue input
1 V/I (0-1V, 0-5V, 0-10V, 0...20mA, 4...20mA)
(selectable by parameter H00)
Maximum load: - current = 100 Ω
- voltage = 20 kΩ
Serial TTL for connection to Copy Card or Televis/
Modbus remote control systems
Digital outputs OUT1: 1 SPDTrelay 8(4)A 250 Va
OUT2: 1 SPST relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -1999 ... 1999
Accuracy better than 0.5% of end of scale +1 digit
Resolution 1 or 0.1 digit according to settings
V/I - 12V, 12-24V
+12V
I
V
+ +−
Supply
OUT1 OUT2
1 2 3 4 5 7 8 9 10 11 12
V/I - 24V, 115V, 230V
+12V
I
V
+ +−
Supply
OUT1 OUT2
1 2 3 4 5 7 9 10 11 126
TERMINALS
1-2-3 regulator relay OUT1 *7-8 Power supply 12Va/c and 12-24Va/12-36Vc.
4-5 regulator relay OUT2 *9-10-12 Voltage input (9=GND; 10=”+”; 12=12V)
*6-7 Power supply 24Va, 115Vaand 230Va.*9-11-12 Current input (9=GND; 11=”+”; 12=12V)
ATTL input for Copy Card and TelevisSystem connection * depends on model
PT100/Tcj-Tck MODEL
CONNECTIONS INPUT/OUTPUT CHARACTERISTICS
Display range:
PT100: -150...650°C
TcJ: -40...750°C
TcK: -40...1350°C
on display with 3½ digits + sign
Digital input 1 digital voltage free input
Analogue input 1 PT100 or 1 TcJ / Tck
(selectable by parameter H00)
Serial TTL for connection to Copy Card or Televis/
Modbus remote control systems
Digital outputs OUT1: 1 SPST relay 8(4)A 250 Va
OUT2: 1 SPST relay 8(4)A 250 Va
Buzzer output only on models where this is provided
Measurement range -150 ... 1350°C (-238 ...2462°F)
Accuracy see ‘Pt100/TcJ/TcKmodels’ table
Resolution see ‘Pt100/TcJ/TcKmodels’ table
PT100/Tcj-Tck - 12V, 12-24V
D.I.
Supply
Pb1
+−
OUT2
1 2 3 4 6 7 8 9 10 11 12
OUT1
PT100/Tcj-Tck - 24V, 115V, 230V
D.I.
Supply
Pb1
+−
OUT2
1 2 3 4 5 6 8 9 10 11 12
OUT1
TERMINALS
1-2 regulator relay OUT1 8-9 Digital Input (D.I.)
3-4 regulator relay OUT2 *10-11-12 Probe PT100 input - 3 wires (Pb1)
*5-6 Power supply 24Va, 115Vaand 230Va.*11-12 TcJ/TcK input
*6-7 Power supply 12Va/c and 12-24Va/12-36Vc.
ATTL input for Copy Card and TelevisSystem connection * depends on model
PT100/Tcj-Tck MODELs
PT100: ACCURACY: 0.5% for whole scale + 1 digit
0.2% from -150 to 300°C
RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
TcJ: ACCURACY: 0.4% for whole scale + 1 digit
RESOLUTION: 0.1°C (0.1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
Tck: ACCURACY: 0.5% for whole scale + 1 digit
0.3% from -40 to 800°C
RESOLUTION: 0.1°C (0,1°F) from -199.9°C up to 199.9°C; 1°C (1°F) beyond
MOUNTING - DIMENSIONS
The device is designed for panel mounting. Drill a 29x71 mm hole and insert the instrument; secure it with the special brackets provided.
Do not install the instrument in damp and/or dirty places; in fact, it is suitable for use in places with ordinary or normal levels of pollution.
Keep the area around the instrument cooling slots adequately ventilated.
74 mm
32 mm
29 mm
71 mm
70 mm
59 mm
EWPA-EWHS PROBE CONFIGURATION
EWPA 007/030 2 wires / Transducer
Transducer
brown
white
9101112
EWHS 304/314 3 wires
Probe
GND (only EWHS314)
V+
RH/T
9101112
EWHS 284 2 wires
Probe
brown
blue
9101112
EWHS 314 4 wires (V-I model)
Probe
GND
V+
RH
T
GND
ICPlus
1I
CPlus 2
91011129101112
ACCESSING AND USING THE MENUs
The resources are organized into 2 menus which are accessed as follows:
• ‘Machine Status’ menu: press and release the key.
• ‘Programming’ menu: hold down the key for 5 seconds.
Either do not press any keys for 15 seconds (timeout) or press the key once, to confirm the last value displayed and return to the previous
screen.
PASSWORD
Password ‘PA1’: used to access User parameters. The password is not enabled by default (PS1=0).
To enable it (PS1≠0): press and hold for longer than 5 seconds, scroll through the parameters using and until you see the label
PS1, press to display the value, modify it using and , then save it by pressing or . If enabled, it will be required in
order to access the User parameters.
Password ‘PA2’: used to access Installer parameters. The password is enabled by default (PS2=15).
To modify it (PS2≠15): press and hold for longer than 5 seconds, scroll through the parameters using and until you see the
label PA2, press , set the value to ‘15’ using and , then confirm using . Scroll through the folders until you find the label
diS and press to enter. Scroll through the parameters using and until you see the label PS2, press to display the value,
modify it using and , then save it by pressing or .
The visibility of ‘PA2’ is as follows:
1) PA1 and PA2 ≠ 0: Press and hold for longer than 5 seconds to display PA1 and PA2. It will then be possible to decide whether to
access the User parameters (PA1) or the Installer parameters (PA2).
2) Otherwise: The password PA2 is amongst the level1 parameters. If enabled, it will be required when accessing the Installer
parameters; to enter it, proceed as instructed for password PA1.
If the value entered is incorrect, the label PA1/PA2 will be displayed again and the procedure will need to be repeated.
MACHINE STATUS MENU
Access the Machine Status menu by pressing and releasing the key. If no alarms are active, the ‘SEt’ label appears.
Use the keys and to scroll through all the folders in the menu:
- AL:alarms folder (only visible if an alarm is active);
- SP1:Setpoint 1 setting folder;
- SP2:Setpoint 2 setting folder;
- Pb1:probe 1 - Pb1 folder;
Setting the Setpoint: To display the Setpoint value press the key when the ‘SEt’ label is displayed.
The Setpoint value appears on the display. To change the Setpoint value, press the and keys within 15
seconds. Press to confirm the modification.
Displaying probes: When label Pb1 is present, press the key to view the value measured by the corresponding probe (NOTE:
the value cannot be modified).
PROGRAMMING MENU
To access the ‘Programming’ menu, press the key for more than 5 seconds. If specified, an access PASSWORD will be requested: ‘PA1’ for
User parameters and ‘PA2’ for Installer parameters (see ‘PASSWORD’ paragraph).
User Parameter: When accessed, the display will show the first parameter (e.g. ‘diF’). Press and to scroll through all the parameters on
the current level. Select the desired parameter by pressing . Press and to modify it and to save the changes.
Installer Parameter: When accessed, the display will show the first folder (e.g. ‘CP’). Press and to scroll through the folders on the
current level. Select the desired folder using . Press and to scroll through the parameters in the current folder and select the
parameter using . Press and to modify it and to save the changes.
NOTE: Make sure you switch the instrument off and on again each time the parameter configuration is changed, in order to prevent mal-
functioning in the configuration and/or timing in progress.
Table des matières
Autres manuels Eliwell Contrôleurs
Eliwell
Eliwell ID 971 Manuel utilisateur
Eliwell
Eliwell EWRC 500 NT Series Manuel utilisateur
Eliwell
Eliwell EWDR 983/CS Manuel utilisateur
Eliwell
Eliwell ID 961 Manuel utilisateur
Eliwell
Eliwell IC 912 LX Pt100 R Manuel utilisateur
Eliwell
Eliwell EW961 Manuel utilisateur
Eliwell
Eliwell ID 970 Manuel utilisateur
Eliwell
Eliwell EZ-HT Manuel utilisateur
Eliwell
Eliwell IC 915 NTC/PTC Manuel utilisateur
Eliwell
Eliwell ECH 200BD "Adaptive" Manuel utilisateur
Eliwell
Eliwell IWP 740 Manuel utilisateur
Eliwell
Eliwell EWDB 111 Manuel utilisateur
Eliwell
Eliwell EWHT 1800LX Manuel utilisateur
Eliwell
Eliwell IC 912 Manuel utilisateur
Eliwell
Eliwell EWCM 4120 Manuel utilisateur
Eliwell
Eliwell IC 915 NTC/PTC Manuel utilisateur
Eliwell
Eliwell EW 4800 Manuel utilisateur
Eliwell
Eliwell EWHT 1800LX Manuel utilisateur
Eliwell
Eliwell EWRC 300 NT Series Manuel utilisateur
Eliwell
Eliwell ID 974 Manuel utilisateur
