Elinx EIR405-T Manuel utilisateur
i Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
E
EI
IR
R4
40
05
5-
-T
T
U
Us
se
er
r
M
Ma
an
nu
ua
al
l
ii Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
E
EI
IR
R4
40
05
5
-
-
T
T
D
Do
oc
cu
um
me
en
nt
ta
at
ti
io
on
n
N
Nu
um
mb
be
er
r:
:
E
EI
IR
R4
40
05
5
-
-
T
T-
-
0
01
10
09
9m
m
U
Us
si
in
ng
g
d
do
om
me
es
st
ti
ic
c
a
an
nd
d
i
im
mp
po
or
rt
te
ed
d
p
pa
ar
rt
ts
s
b
by
y
International
Headquarters
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics Ltd.
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
©2008 B& B Electronics Mfg. Co. Inc. No part of this publication may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including photography, recording, or any information
storage and retrieval system without written consent. Information in this manual is subject to change
without notice, and does not represent a commitment on the part of B&B Electronics Mfg. Co. Inc.
B&B Electronics Mfg. Co. Inc. shall not be liable for incidental or consequential damages resulting from the
furnishing, performance, or use of this manual.
All Brand names used in this manual are the registered trademarks of their respective owners. The use of trademarks or other
designations in this publication is for reference purposes only and does not constitute an endorsement by the trademark holder
Table of Contents
Table of Contents
1. Overview ............................................................................................................................................................1
Introduction.......................................................................................................................................................1
Features............................................................................................................................................................2
Packing List.......................................................................................................................................................2
2. Hardware Description .......................................................................................................................................3
Front Panel .......................................................................................................................................................3
Top View...........................................................................................................................................................4
Wiring the Power Inputs....................................................................................................................................4
Wiring the Fault Alarm Contact.........................................................................................................................5
LED Indicators ..................................................................................................................................................6
Ports..................................................................................................................................................................6
Cabling..............................................................................................................................................................8
3. Mounting Installation ......................................................................................................................................11
DIN-Rail Mounting...........................................................................................................................................11
Wall Mount Plate Mounting.............................................................................................................................13
4. Hardware Installation......................................................................................................................................14
Installation Steps.............................................................................................................................................14
5. Troubleshooting..............................................................................................................................................16
6. Technical Specification...................................................................................................................................17
iii Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Overview
1 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Overview
Introduction
The EIR405-T is an industrial DIN mount, unmanaged 5 port Gigabit Ethernet switch.
High-Speed Transmissions
The EIR405-T includes a switch controller that can automatically sense transmission
speeds (10/100/1000 Mbps). The RJ-45 interface can also be auto-detected, so MDI or
MDI-X is automatically selected and a crossover cable is not required. All Ethernet ports
have memory buffers that support the store-and-forward mechanism. This assures that
data is properly transmitted
Dual Power Input
To reduce the risk of power failure, the EIR405-T provides two 12 to 48 VDC power
inputs. If the power fails, the switch will automatically switch to the secondary power
input. Also if the power goes out the corresponding P1 or P2 LED will go out and the
Fault LED will light. The contacts for the alarm output will also open.
Flexible Mounting
The EIR405-T can be DIN or Panel mounted. The compact design is suitable for
space-constrained environment such as a small cabinet.
Advanced Protection
The power line input on the EIR405-T supports up to 3,000 VDC EFT protection, which
secures the equipment against unregulated voltages and makes the system safer and more
reliable. The Ethernet ports support up to 6,000 VDC ESD protections which makes the
switch suitable for harsh environments.
Wide Operating Temperature
The operating temperature of the EIR405-T is -40 to 75oC. This wide range allows the
switch to be used in some of the harshest industrial environments that exist.
Overview
2 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Easy Troubleshooting
LED indicators make troubleshooting quick and easy. There are 2 LED’s for each port
that display the link status and transmission speed. Three LED’s P1, P2 and Fault help
you diagnose if power is present.
Features
•Provides 5 x 10/100/1000Base-T Mbps Ethernet ports.
•Supports full/half duplex flow control
•Supports auto-negotiation (10/100/1000)
•Supports MDI/MDI-X auto-crossover
•Supports Jumbo Frame of 9Kbytes
•Supports surge (EFT) protection 3,000 VDC for power input
•Supports 6,000 VDC Ethernet ESD protection
•Supports redundant 12 to 48 VDC power inputs
•Provides flexible mounting: DIN-rail or Panel Mounting
•Supports operating temperatures from -40 to 75oC
Packing List
•(1) EIR405-T, 5 Port Gigabit Industrial Ethernet Switch
•(1) Quick Start Guide
•(1) CD ROM with User Manual
•(2) Wall Mounting Bracket and Screws
Hardware Description
3 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Hardware Description
Front Panel
The Front Panel view of the EIR405-T is shown below.
Hardware Description
4 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Top View
The top panel view of the EIR405-T is equipped with one terminal block connector that
consists of two 12 to 48 VDC power inputs and the fault alarm output.
Wiring the Power Inputs
Follow the steps below to insert the power wires.
1. Insert the positive and negative wires into the V+ and V- contacts on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the wires from becoming loose.
Hardware Description
5 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
Wiring the Fault Alarm Contact
The fault alarm contact is in the middle of terminal block connector as the picture shows
below. If one of the power sources fails a fault will be detected causing the circuit to open.
Note The wire gauge for the terminal block should be 12 to 24 AWG.
Insert the wires into the fault alarm contact (No. 3 & 4)
Hardware Description
6 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
LED Indicators
Below is a table that explains the status of each the power and network status LED’s
found on the front panel of the EIR405-T.
LED Color Description
On Power input 1 is active
P1 Green
Off Power input 1 is inactive
On Power input 2 is active
P2 Green
Off Power input 2 is inactive
On Power input 1 or 2 is inactive
Fault Red
Off Power inputs 1 and 2 are both active, or no power is
present
On Connected to network
Flashing Networking is active
Ports 1 to 5
(Upper LED) Green
Off Not connected to network
On Connected to network at speed of 1000MbpsPorts 1 to 5
(Lower LED) Green Off Not connected to 1000Mbps network
Ports
RJ-45 ports: The RJ-45 ports auto-sense for 10, 100 or 1000 Mbps devices connections.
The auto MDI/MDIX feature allows connections to switches, workstation and other
equipment without changing straight through or crossover cabling. The charts below
show the cable pin assignments for straight through and crossover cables.
Hardware Description
7 Manual Documentation Number EIR405-T – 0109m
www.bb-elec.com
www.bb-europe.com
RJ-45 Pin Assignments
Pin Number Assignment
1 Tx+
2 Tx-
3 Rx+
6 Rx-
Note “+” and “-” signs represent the polarity of each wire pair.
All ports on the EIR405-T support automatic MDI/MDI-X operation, you can use
straight-through cables (See Figure below) for all network connections to PCs or servers,
or to other switches or hubs. In straight-through cables, pins 1, 2, 3, and 6, at one end of
the cable, are connected straight through to pins 1, 2, 3 and 6 at the other end of the cable.
The table below shows the 10BASE-T / 100BASE-TX MDI and MDI-X port pin outs.
Pin MDI-X Signal Name MDI Signal Name
1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
Straight Through Cable Schematic
Table des matières
Autres manuels Elinx Routeur réseau
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité