Electrolux EDW 1600 Manuel utilisateur

Consumer Service - EMEA

Quality & Continuous Improvement - Technical Support

SERVICE MANUAL

DISHWASHERS

FOR INTERNAL AND PARTNERS USE ONLY

For internal and partners use only.

Publication number

599 83 22 - 09

Edition: 08/2019 - Rev. 0

Dishwashers with electronic control system

SERVICE MODE

• EDW 1600 • EDW 1850

• EDW 1950 • EDW 2200

• EDW 3510 • EDW 4010

Introduction & Purpose

Technical Support – RA

Chapter

CONTENTS:

Introduction & Purpose Chapter 1

User Interface – Introduction Chapter 2

EDW 1600 Chapter 3.1

EDW 1850 Chapter 3.2

EDW 1950 Chapter 3.3

EDW 2200 Chapter 3.4

EDW 3510 Chapter 3.5

EDW 4010 Chapter 3.6

Purpose:

To describe all the Service Mode functions for the User Interfaces included

on this Service Manual

Abbreviations, Acronyms and Definitions

RTA Remaining time adaptation

MCF Machine Configuration File

NTC

PB100

DIVA2

MCB

ADO

Negative Temperature Coefficient resistor

New platform for dual BLDC machines (Global hydraulic)

Platform with single BLDC control in separate unit (MCB)

Motor Control Board (DIVA2)

Auto Door Opener

Document Revisions

Revision Date Description Author

V0.0 08/2019 Document creation Rui Almeida

Electrical appliances must be serviced only

by qualified Service Engineers.

Always use proper safety equipment.

Always remove the plug from the power

socket before touching internal components.

User interface – Introduction

Technical Support – RA

Chapter

User Interface – Modes and Function description

Reset

“Reset” is a special kind of User Operation to stop or deselect a

running program. In Dorothea range, when this function is

performed, the appliance will be in Startup mode with ECO program

and its default option selected.

Reset can be performed in any state except the Startup mode.

Reset is done by pressing the reset key combination for at least 2

seconds or press the specific button dedicated to this function by

the custom software.

The Reset key combination or specific Reset key is clearly indicated

on the control panel as ‘Reset’ or ‘Cancel’.

User Mode

The full function User Mode includes:

•Water Hardness Setting

•Rinse Aid Level Setting

•End of Cycle Buzzer Setting

•Display on Floor Display Colour Setting

•ADO Setting

According to hardware configuration of the dishwasher and

marketing requirement, User Mode in individual models can be a

subset of above functions.

The User Mode functions are not described in this Service Manual

since they are available on the User Manual.

Service Mode

The full function Service Mode includes:

•Fault Memory Reading

•Actuator Test

•LEDTest

•Functional Test cycle

•Enable/disable Extra Rinse

•Enable/disable Pulse Wash

•LCD brightness setting

•LCD contrast setting

According to hardware configuration of the dishwasher and

marketing requirement, Service Mode in individual models can be a

subset of above functions.

All the Service Mode functions are described on this user Service

Manual.

User interface – Introduction

Technical Support – RA

Chapter

Service Mode – Function description

Alarm Reading and Actuator Test

After accessed Service mode to get the saved alarms and test

actuators.

Details of alarm code displaying are in later Alarm Code section.

LED Test / Delete Alarm Memory

To test the LEDS and erase alarm codes from memory.

Functional Test Cycle

Run a test cycle. It runs as a normal wash cycle. It can be cancelled

or run to its end.

Enable/disable Extra Rinse

An additional cold rinse phase can be added to the cycles to

improve wash performance. In factory (default) settings, this is

disabled.

Use this function to enable or disable the Extra Rinse.

Enable/disable Pulse Wash

Pulse Wash can be disabled from the cycles to improve wash

performance. In factory (default) settings, this is enabled.

Use this function to disable or enable Pulse Wash.

EDW1600

Technical Support – RA

Chapter

EDW 1600

Styling Overview

Location of LEDs and Push Buttons

Reset

Press buttons S1+S2 simultaneously for at least 2 seconds to

perform Reset function.

Access Service Mode

The Service Mode can only be accessed after the Reset function

has been carried out and the appliance is switched off.

Press and hold button S1+S2 simultaneously while turn the

appliance on, keep holding the buttons for 4 seconds.

L1, L2 and L3 blink to indicate that Service mode is accessed.

EDW1600

Technical Support – RA

Chapter

Alarm Reading and Actuator Test

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S1 to show the first alarm code.

L1 blinks to indicate the machine is in Alarm Reading.

The first alarm code saved is shown in the display. Please

see later Alarm Codes section.

2. Press button S1 again to show the second alarm code.

3. Press button S1 once more to show the third alarm code.

4. Press button S1 the fourth time to move to Actuator Test. Press

button S1 repeatedly will sequentially turn on one actuator at a

time.

L1 is turned off. L2 blinks to indicate the machine is in

Actuator Test.

The actuator number is shown in the display, see the

following table for details.

Number of

S Pressed

Actuator

Number in

Display

Actuator Comment

4 4 Regeneration Valve

5 5 Drain Pump

6 6 Inlet Valve

Off hen ater level

reached

7 7 Heater

On only if ater level

reached

8 8 Wash Pump

9 9 Dispenser

10 10 Auto door opening

5. Press button S1 when actuator number 10 is activated, the

machine will cycle back to Alarm reading and show the first

alarm code saved.

6. Switching off the appliance will exit Service mode.

LED Test / Delete Alarm Memory

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S2 to start this function.

All used LEDS and display (show “8:88”) blinks 5 second on

1 second off.

If a buzzer is equipped, it beeps for 5 seconds.

The alarm codes saved in memory are erased.

2. Switching off the appliance will exit Service mode.

EDW1600

Technical Support – RA

Chapter

Functional Test Cycle

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S3 to start the test cycle. The cycle will not start if

door is opened.

L3 blinks for the duration of the test cycle.

Display shows the remaining time of test cycle.

The test cycle runs as a normal wash cycle. It can be

cancelled or run to its end.

Enable/disable Extra Rinse

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S1+S2 to enter this function.

L1 blinks indicating it is in Extra Rinse setting mode.

Display show the current setting of Extra Rinse. “0E” for

disabled, “1E” for enabled.

2. Press button S1 to change the setting.

3. Switching off the appliance will exit Service mode.

Enable/disable Pulse Wash

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S2+S3 to enter this function.

L2 blinks indicating it is in Pulse Wash setting mode.

Display show the current setting of Pulse Wash. “0P” for

disabled, “1P” for enabled

2. Press button S2 to change the setting

3. Switching off the appliance will exit Service mode.

EDW1850

Technical Support – RA

Chapter

EDW 1850

Styling Overview

Location of LEDs and Push Buttons

Reset

Press buttons S3+S4 simultaneously for at least 2 seconds to

perform Reset function.

Access Service Mode

The Service Mode can only be accessed after the Reset function

has been carried out and the appliance is switched off.

Press and hold button S1+S2 simultaneously while turn the

appliance on, keep holding the buttons for 4 seconds.

EDW1850

Technical Support – RA

Chapter

L1, L2 and L3 blink to indicate that Service mode is accessed.

Alarm Reading and Actuator Test

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S1 to show the first alarm code.

L1 blinks to indicate the machine is in Alarm Reading.

The first alarm code saved is shown in the display.

Please see later Alarm Codes section.

2. Press button S1 again to show the second alarm code.

3. Press button S1 once more to show the third alarm code.

4. Press button S1 the fourth time to move to Actuator Test. Press

button S1 repeatedly will sequentially turn on one actuator at a

time.

L1 is turned off. L2 blinks to indicate the machine is in

Actuator Test.

The actuator number is shown in the display, see the

following table for details.

Number of

S Pressed

Actuator

Number in

Display

Actuator Comment

4 4 Regeneration Valve

5 5 Drain Pump

6 6 Inlet Valve

Off hen ater

level

reached

7 7 Heater

On only if ater level

reached

8 8 Wash Pump

9 9 Dispenser

10 10 Auto door opening

5. Press button S1 when actuator number 10 is activated, the

machine will cycle back to Alarm reading and show the first

alarm code saved.

6. Switching off the appliance will exit Service mode.

LED Test / Delete Alarm Memory

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S2 to start this function.

All used LEDS and display (show “8:88”) blinks 5 second on

1 second off.

If a buzzer is equipped, it beeps for 5 seconds.

The alarm codes saved in memory are erased.

2. Switching off the appliance will exit Service mode.

EDW1850

Technical Support – RA

Chapter

Functional Test Cycle

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S3 to start the test cycle. The cycle will not start if

door is opened.

L3 blinks for the duration of the test cycle.

Display shows the remaining time of test cycle.

The test cycle runs as a normal wash cycle. It can be

cancelled or run to its end.

Enable/disable Extra Rinse

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S1+S2 to enter this function.

L1 blinks indicating it is in Extra Rinse setting mode.

Display show the current setting of Extra Rinse. “0E” for

disabled, “1E” for enabled.

2. Press button S1 to change the setting.

3. Switching off the appliance will exit Service mode.

Enable/disable Pulse Wash

After accessed Service mode (L1, L2 and L3 blinking):

1. Press button S2+S3 to enter this function.

L2 blinks indicating it is in Pulse Wash setting mode.

Display show the current setting of Pulse Wash. “0P” for

disabled, “1P” for enabled

2. Press button S2 to change the setting

3. Switching off the appliance will exit Service mode.

Autres manuels pour EDW 1600

Ce manuel convient aux modèles suivants

Autres manuels Electrolux Lave-vaisselle

Electrolux

Electrolux DIVA Manuel utilisateur

Electrolux

Electrolux ESL 6180 Manuel utilisateur

Electrolux

Electrolux ESL 5201LO Manuel utilisateur

Electrolux

Electrolux 60 cm Series Manuel utilisateur

Electrolux

Electrolux ESF4100 Manuel utilisateur

Electrolux

Electrolux EEM48330L Manuel utilisateur

Electrolux

Electrolux GA55GL201 Manuel utilisateur

Electrolux

Electrolux ESI 68850 Manuel utilisateur

Electrolux

Electrolux EIDW1805KS Guide de l'utilisateur

Electrolux

Electrolux ESF 66814 Manuel utilisateur

Electrolux

Electrolux ESF 66010 Manuel utilisateur

Electrolux

Electrolux ESF 662 Manuel utilisateur

Electrolux

Electrolux EDW 1003 Manuel utilisateur

Electrolux

Electrolux 506029 Manuel utilisateur

Electrolux

Electrolux EIDW5705PB Guide de démarrage rapide

Electrolux

Electrolux ESF5512LOX Manuel utilisateur

Electrolux

Electrolux EEG68520W Manuel utilisateur

Electrolux

Electrolux ESI 63010 Manuel utilisateur

Electrolux

Electrolux ESF6140 Manuel utilisateur

Electrolux

Electrolux ESF6768KXA Manuel utilisateur

Electrolux

Electrolux ESI6515LAK Manuel utilisateur

Electrolux

Electrolux ESI 66065 Manuel utilisateur

Electrolux

Electrolux ESI66050 Manuel utilisateur

Electrolux

Electrolux ESL 4114 Manuel utilisateur

Manuels Lave-vaisselle populaires d'autres marques

KitchenAid

KitchenAid KUDB230B Manuel utilisateur

Brandt

Brandt BDJ424DB Manuel utilisateur

Asko

Asko DSD767UXXL.AU Manuel utilisateur

Beko

Beko DFN26210W Manuel utilisateur

NEFF

NEFF S153ITX00E Fiche technique

Midea

Midea SV 4.45 wi Manuel utilisateur

LG LDF7932 Manuel utilisateur

Gorenje

Gorenje GV63214 Manuel utilisateur

Hotpoint

Hotpoint HDA1100ZWH Manuel de service

Blomberg

Blomberg LDFN2240W Manuel utilisateur

AEG

AEG FFB83836PM Manuel utilisateur

Cylinda

Cylinda DM3220RFD Manuel utilisateur

Atag

Atag DW8214MB Manuel utilisateur

GE GLD8000 Series Manuel utilisateur

Siemens

Siemens SN23HI02KE Fiche technique

Omega

Omega ODW717X Manuel utilisateur

BORETTI

BORETTI BVW-683 Manuel utilisateur

Siemens

Siemens SN 56N591 Manuel utilisateur