Electro Industries/GaugeTech 3DAA5 Manuel utilisateur

Electro Industries/GaugeTech

Doc# E104779 Q-1

Quick Start Guide for 3DAA5/3DAA5-H Meters

Hardware Installation

NOTE: For 50 Hz power systems—Connect phase A voltage to terminal 5 and neutral to terminal 4. Do not exceed 300 VAC

L-N. This provides a frequency reference. If no frequency reference is connected, the unit will default to 60 Hz operation.

Meter Dimensions and Cut-out

Electrical Installation

Three-Phase, Four-Wire Wye with 3 CTs Three-Phase, Three-Wire Delta System Wye with 2 CTs

Electro Industries/GaugeTech

Doc# E104779 Q-2

Programming the Meter

- Basic programming information is given here. For step-by-step instructions refer to the meter’s User manual, on the enclosed CD.

- Programming tasks are divided into 9 Groups that contain programming Functions. Use the meter buttons to access the Groups/

Functions and program the meter.

- Programmable Function values are always four-digit numeric elds. For example, to enter the number 25, you must enter 0025.

Enter Programming Mode:

1. Press and hold PRINT/PROG until 3 appears in the bottom display.

2. Press SET (3DAA5) or THD/K (3DAA5-H) to multiply the 3 to 333.

3. Digits begin scrolling in the upper display. Press SET or THD/K each time 5 appears, until the bottom display reads 555 (this is the

meter’s password.

4. PPP and then 0 appear in the upper display: the meter is now in programming mode for Group 0.

Exit Programming Mode: IMPORTANT! You MUST exit Programming Mode to store any changes.

NOTE: The steps to exit Programming Mode depend on your current stage. If you are located at Function level begin at Step 1; if you

are located at Group level, begin at Step 3.

1. Press C/N until the Group number in the upper display is followed by E (Exit).

2. Press PRINT/PROG to return to Group level.

3. Press C/N until E appears in the upper display.

4. Press PRINT/PROG to exit Programming Mode.

Programming Amp Full Scale Settings

1. Enter programming mode (see instructions above).

2. Press C/N until 1 appears in the upper display.

3. Press PRINT/PROG to activate GROUP 1: 10 appears in the upper display; the current value

appears in the lower display, and the middle display contains a vertical line indicating Scale factor:

- an UP position signies Kiloamps

- a DOWN position signies Amps.

See the example gure on the right.

4. Press PRINT/PROG to begin data entry: the lower display is replaced with a single dash.

5. Press MAX/MIN/LIMITS to set the Scale factor by moving the vertical line UP (for Kiloamps)

or DOWN (for Amps).

6. Press PRINT/PROG to store the value. A decimal point appears in the lower display.

7. Press MAX/MIN/LIMITS to move the decimal point, then press PRINT/PROG to store the setting.

NOTE: If the decimal point is already where you want it, press PRINT/PROG to continue.

8. The middle display contains the present Full Scale for Amps and four dashes appear in the lower display for data entry. Enter

the four digit Full Scale value you want by pressing MAX/MIN/LIMITS to increase the digit’s value, and then pressing

PRINT/PROG to store each digit. Repeat until all four digits are entered.

9. The lower display contains the new Full Scale setting; the middle display indicates the Scale Factor; the Group and Function

number appear in the upper display. IMPORTANT! When you are done, follow the Exiting procedure described above.

NOTE: Refer to your meter’s User manual on the enclosed CD for step-by-step instructions for additional programming tasks.

Electro Industries/GaugeTech

1800 Shames Drive Westbury, New York 11590

Tel: 516-334-0870

FAX: 516-338-4741

www.electroind.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Electro Industries/GaugeTech Instrument de mesure

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1500+ Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1250 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1450 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1262 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 250 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark NEMA 1 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1262 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1450 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100S Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech SBM 100 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 50 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 270 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100T Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 270 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 100 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Shark 270 Manuel utilisateur

Electro Industries/GaugeTech

Electro Industries/GaugeTech Nexus 1250 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur