Eldes ESIM120 Manuel utilisateur

GSM SWITCH  GATE CONTROLLER

ESIM120

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced written authorization from

“ELDES UAB”. “ELDES UAB”reserves the right to update or modify this document and/or related products without a warning. Hereby, ELDES UAB

declares that this GSM Switch -Gate controller ESIM120 is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt.

User Manual v1.0

Safety instructions

Please read and follow these safety guidelines and assembly instructions in order to maintain safety of operators and people around:

• GSMcontrolsystemESIM120(furtherreferencedasthesystemordevice)containsanintegratedradiotransceiveroperatingin

GSM 850/900/1800/1900 MHz bands.

DO NOT use the system where it can interfere with other devices and cause any potential danger.

• DONOTmountthesystemnexttomedicalequipmentordevices,iftheyrequireso.

• DONOTusethesysteminhazardousenvironment.

• DONOTexposethesystemtohighhumidity,chemicalenvironmentormechanicalimpacts.

• DONOTattempttopersonallyrepairthesystem.

• Systemlabelisonthebottomsideofthedevice.

System ESIM120 is a device mounted in limited access areas. Any system repairs must be done only by qualied, safety aware

personnel.

Mains power must be disconnected before any installation or tuning work starts. The system installation or maintenance

must not be done during stormy conditions.

The system must be powered by main 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply which must be

approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the

system, switching the terminals places does not have any aect.

AnyadditionaldeviceslinkedtothesystemESIM120(computer,sensors,relaysetc.)mustbeapprovedbyLSTEN60950-1

standard.

External power supply can be connected to AC mains only inside

installation room with automatic 2-pole circuit breaker capable of

disconnecting circuit in the event of short circuit or over-current

condition. Open circuit breaker must have a gap between con-

nections of more than 3mm and the disconnection current 5A.

FuseF1modelMINISMDC050F0.5A.Blownfusecannotbereplacedbytheuserandthereplacementfuseshavetobeexactlythe

same as indicated by the manufacturer.

Thedeviceisfullyturnedobydisconnecting2-poleswitchodeviceoftheexternalpowersupplyoranyotherlinked

device that the system ESIM120 is powered from.

TheWEEE (WasteElectrical andElectronicEquipment)markingon thisproductor its documentationindicatesthatinthe EUthe

product must not be disposed of together with household waste.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

ESIM120

AC/DC

If you use I security class computer for setting the parameters it must be connected to earth.

Limited Liability

The buyer must agree that the system will re-

duce the risk of re, theft, burglary or other dan-

gers but does not guarantee against such events.

“ELDES UAB” will not take any responsibility

regarding personal, property or revenue loss while

using the system.

“ELDES UAB” responsibility according to local

lawsdoesnotexceedvalueofthepurchasedsys-

tem.

“ELDES UAB” is not aliated with GSM opera-

tors providing cellular services therefore is not res-

ponsible for the quality of cellular services.

Manufacturer Warranty

The system carries a 24-month warranty by the

manufacturer “ELDES UAB”.

Warranty period starts from the day the system

has been purchased by the end user. The warranty

is valid only if the system has been used as inten-

ded, following all guidelines listed in the manual

and within specied operating conditions. Receipt

with purchase date must be kept as a proof.

The warranty is voided if the system has been

exposed to mechanical impacts, chemicals, high

humidity, uids, corrosive and hazardous environ-

ment or other force majeure factors.

Content:

1. The system ESIM120 ............................................1pcs

2. ESIM120 user manual..........................................1pcs

3. GSM antenna.................................... .....................1pcs

About User Manual

This document describes GSM switch - gate controller ESIM120, its operation and installation.

It is very important to read User Manual before start using the system. A quick start guide is located in rst two chapters. Chap-

ter 3 describes additional system capabilities.

CONTENT

1. General Information......................................................... 4

1.1 Function..................................................................................................................4

1.2 Operation Description.......................................................................................4

1.3 Technical Specications ....................................................................................4

1.4 Connector and LED Indicators Functionality ...........................................5

1.5 Connection Circuit..............................................................................................5

1.6 System Installation..............................................................................................5

2. System Pre-operation, Control & Conguration............6

2.1 System Language................................................................................................6

2.2 SMS Password.......................................................................................................7

2.3 Administrator Phone Numbers ......................................................................7

2.4 Date & Time Settings..........................................................................................8

2.5 User Database Management...........................................................................9

2.6 Scheduler Settings...........................................................................................15

2.7 Output Conguration.....................................................................................16

2.8 Input & Output Status..................................................................................... 18

2.9 Input Conguration.........................................................................................18

2.10 Info SMS.............................................................................................................19

2.11 Conrmation by Call upon Output Control Action ...........................20

2.12 Control from any Phone Number.............................................................21

2.13 Event Log Deletion........................................................................................22

2.14 System Restart ................................................................................................22

3. Appendix.........................................................................23

3.1 Restoring Default Parameters...................................................................... 23

3.2 Eldes Conguration Tool software ...............................................................23

3.3 ESIM120 control by GPRS .............................................................................. 23

3.4 Technical Support............................................................................................. 26

1. General Information

1.1 Function

ESIM120 is a micro-controller based 2-relay device intended to control gate automatics, road barriers or to remotely turn on/o

any electronic device over GSM network.

Examples of using the system:

• Roadbarriercontrolintheparkinglotofresidentialhousesoroces

• Controllinggatesofprivatehouses

• Electronicappliancecontrolforaspeciedperiod.E.g.,turnon/oaquariumlighting,pump,watering,heatingetc.

• Turnoncomputersystem

• Turnon/oanyelectricappliance

• ”Frozen“systemreboote.g.computernetwork,server

• Noticationaboutafaultingateorotherautomatics.

1.2 Operation Description

System ESIM120 operates over GSM network. Gates are opened or any other electric appliance is turned on/o by making a phone

call to the system. The phone call is automatically rejected by the system, therefore the phone call becomes free of charge.

On calling to the phone number of the system it checks whether the caller is one of the administrators or stored in the user da-

tabase.Iftheuserisstoredinthesystem,thespeciedoutput(-s)foraparticularuseristurnedon/oforaspeciedperiod.The

system will ignore incoming requests from an unknown telephone number or SMS message containing wrong password.

By connecting the opened-gate/barrier sensor to one of the 3 inputs, the administrators can receive SMS message about the gates

that did not close during the set time period.

Thereare3waysofconguration:SMSmessages,overUSBcableorInternet(deviceconnectoverGPRS).

1.3 Technical Specications

Electrical, mechanical and other specications

Supply voltage 10-24V50Hz~200mAmax/10-24V 200mAmax

Current used in standby model not more than 50mA

GSM modem frequency 850/900/1800/1900 MHz

Number of outputs 2

Output type NO(relay)

Numberof“low”level(negative)inputs 2

Numberof“high”level(positive)inputs 1

Allowable“low”level(negative)inputvalues Voltage: 0... 16V; current: -0.8... -0.4mA

Allowable“high”level(positive)inputvalues Voltage: 5... 50V; current: 0.17 .... 1.7mA

Relayoutputmaximumcommutatingvalues 24V 1A / 24V 50Hz ~0,5A

Dimensions 70x85x57mm

Operating temperature range -20…+55oC(-30...+55oCwithlimitations)

Number of administrators 5

Number of users 500(1000optional)

MANUAL ELDES ESIM120 V1.0 5

1.4 Connector and LED Indicators Functionality

1.5 Connection Circuit

1.6 System Installation

The system can be installed only in a metal or non-ammable plastic enclosure. If the metal enclosure and transformer is used it

isnecessarytogroundtheenclosureusingyellow/greencolourcable.Fortheconnectionof230Vtransformeruse3x0.75mm2

1 thread double isolated cable. The primary circuit of the transformer must be connected through 0.5A fuse. 230V power supply

cables cannot be grouped with low voltage cable group. For the connection of power supply and output connectors use 1 thread

2x0.75mm2cable. For the connection of input/output connectors use 0.50 mm21 thread cable.

1. PlaceSIMcardintheholderbutmakesurethatSIMcardPINcodeisdisabled(PINcodecanbedisabledbyputtingSIMcard

intomobilephoneandfollowingpropermenus).SIMcardshouldnothaveanyremainingSMSmessages.

2. Connect the circuit as shown in g. No 2. Connect control connectors of the gate automatics device to the relay contacts. The

systems that are already installed most often contain a button for opening the gates.The relay can be connected instead of the

button or in parallel with its contacts.

3. Connect a sensor or switch to inputs Z1-Z3 that turns on only when gates are lifted. Low level signal is connected to Z1 and Z3.

HighlevelsignalisconnectedtoZ2.(Inputconnectionisanadditionalfunctionanditisnotnecessarytoinstall).

4. The system will start in less than a minute. LED2 indicator should be blinking or be ON indicating connection to GSM.

Short explanation of the main units

GSM MODEM GSM network 850/900/1800/1900 MHz modem

SIM CARD SIM card

LED Light-emitting diodes indicator

DEFAULT Connectors(D1andD2)forrestoringdefaultsettings

ANT GSM antenna SMA type connector

USB Mini USB connector

F1 Fuse

Connector functionality

Labeling Explanation

AC/DC Power supply pins

RELAY1 Dryrelaycontact.Normallyopen(NO)

RELAY2 Dryrelaycontact.Normallyopen(NO)

COM Common pin

Z5 Not Connected

Z4 Not Connected

Z3 “Low” level input Z3

Z2 “High”level input Z2

Z1 “Low” level input Z1

Fig. No. 1

ANT

GSM

MODEM

SIM

CARD

MIC

LED1

LED2

DEFAULT D1 D2

AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1

USB

ESIM 120

AC/DC

Power

supply

Gate controller Gate controller

RELAY1 RELAY2

COM Z3 Z2 Z1

Fig. No. 2

NOTE

Althoughthe installationofsystemESIM120 isnotcomplex,wehighly

recommend installing the device only in the case if you have minimal

electrotechnical or electronics knowledge. Otherwise you can damage

the device.

LED indicators functionality

LED1 Indicates SIM card

status

LED2 Indicates network

status

LED1 status Meaning

OFF SIM card is wor-

king properly

ON SIM card

error

LED2 status Meaning

OFF No network connection

Blinking 1 times per second Poor network connection

Blinking 3 time per second Medium network connection

ON Excellentnetworkconnection

2. System Pre-operation, Control & Conguration

VERY IMPORTANT!!!

In this user manual the underscore symbol ”_” represents one <space> character. Every underscore symbol must be replaced

by a single <space> character. There must be no spaces or other unnecesary characters at the beginning and at the end of the

message.XXXX–4-digitSMSpassword(thedefaultSMSpasswordis0000–fourzeros).

For easier and quicker conguration we recommend connecting the system to personal computer via USB cable and installing congura-

tion program ELDES Conguration Tool. Please, refer to chapter 3.2. for more details

The system can also be congured remotely by connecting over GPRS connection. Please, refer to chapter 3.3 for more details.

System conguration and control using SMS messages is performed by sending it to ESIM120 phone number from one of the

authorizedphonenumbers.ThestructureofSMSmessageconsistsof4digitSMSpassword(thedefaultSMSpasswordis0000–four

zeros),theparameterandvalue.Forsomeparametersthevaluedoesnotapply,i.e.STATUS.

Primary Conguration:

1. Set the system language. Please, refer to chapter 2.1 for more details.

2. Once the SMS reply conrming the successful language setup is received, proceed to chapter 2.2

3. Otherwise check the GSM network connection of the system by making a call to the system from any mobile phone. The

SMS reply asking to change the password conrms that GSM signal present.

4. In other case, change the SMS centre phone number.

SMS centre number is stored in SIM card by the GSM operator, therefore if SIM card has already

been successfully used to send SMS messages over a mobile phone, then it is not necessary

to change SMS centre number.

In order to change/enter SMS centre number send the following SMS message to the system.

Language in which the system communicates with the user by SMS messages. The language

must be set before changing factory default SMS password, therefore SMS password is not

required in the following SMS message.

SMS Centre

Phone Number

Set Language

SMS text:

0000_SMS_+37011111111

Example: 0000_SMS_+37069899992

SMS text:

Value: LL – language index, range – [LT - Lithuanian, RU - Rus-

sian, EN - English, EE - Estonian]

Example: EN

2.1 System Language

MANUAL ELDES ESIM120 V1.0 7

AllSMScommandsstartwitha4-digitpassword.Manufacturerdefaultpasswordis0000(four

zeros),whichisnecessarytochange.Non-numericalcharacterslikeletters,dots,colons,spa-

ces are not allowed.

The system supports up to 5 administrator phone number entries allowing full system con-

gurationandcontrol(includingoutputcontrol).User1phonenumberismandatorywhile

other phone number entries are not necessary. All numbers must be entered starting with

international country code e.g. 44[area code][local number]. The plus symbol is not necessary.

Phone number length – up to 15 digits.

To receive the list containing added administrator numbers send the following SMS message.

Set SMS Password

Add Administrator

Numbers

List Administrator

Numbers

SMS text:

0000_PSW_XXXX

Value: XXXX – new 4-digit SMS password

Example: 0000_PSW_1111

SMS text:

XXXX_NR1:37011111111_NR2:37011111112_

NR3:37011111113_NR4:37011111114_NR5:37011111115

Example: 1111_NR1:37011111111_NR3_37011111113

SMS text:

XXXX_HELPNR

Example: 1111_HELPNR

2.2 SMS Password

2.3 Administrator Phone Numbers

This SMS message erases a particular or several administrator phone numbers at once. The

system will not allow erasing of the User 1 phone number. This number can only be modied.

Delete Administrator

Numbers

SMS text:

XXXX_NR2:DEL_NR3:DEL_NR4:DEL_NR5:DEL

Example: 1111_NR4:DEL_NR5:DEL

It is important to set correct date and time so that the system can send reports at specied

times.

Date and time can be set by sending the following SMS message.

Date & Time

SMS text:

XXXX_YYYY.MM.DD_HH:MM

Value: YYYY– year; MM – month, range – [01... 12]; DD – day,

range - [01... 31]; HH – hours, range – [00... 23], MM – minutes,

range – [00... 59].

Example: 1111_2011.12.01_14:15

2.4 Date & Time Settings

MANUAL ELDES ESIM120 V1.0 9

Thesystemsupportsupto500dierentdatabaseusers(1000optional)whichgainaccessto

controltheoutputs(gatesoranyotherelectricapplianceconnectedtotheoutput)bymaking

phone call to the system.

Userentryinthedatabaseconsistsofphonenumber(mandatory),username(notmandato-

ry)andadditionalparameters.

All user numbers must be entered starting with international country code e.g. 44[area code]

[local number]. The plus symbol is not necessary. Phone number length – up to 15 digits.

Length of user name - up to 16 characters.

To receive the list containing added database users send the following SMS message.

Add User

List Users

SMS text:

XXXX_N:37011111111:UserName

Example: 1111_N:37011111111:UserName1_N:37011111112_

N:37011111113:UserName2

SMS text:

XXXX_GETALLNUMBERS

Example: 1111_GETALLNUMBERS

2.5 User Database Management

NOTE:Databaseuserscanbemanagedbyadministrator(-s)only.

NOTE: Afteraddingall500users(1000optional)tothedatabasethesystemwillnotallowtoaddanymoreusers.Inordertoadd

a dierent user, please, delete one or more current database users.

ATTENTION:Depending on entered user numbers and/or user names you might receive more than 55 SMS messages!

This feature allows to erase a particular user or several users from the database. It is possible to

deleteauser(-s)byusernameorbyphonenumber.

Thisfeatureallowstoeraseallusersfromthedatabase(nottheadministratornumbers)at

once.

This feature allows to search for a user in the database. It is possible to search for user by user

name or by phone number.

Delete User (-s)

Delete All Users

Search for User

SMS text:

XXXX_D:37011111111 or XXXX_D:UserName

Example: 1111_D:37011111111_UserName2_UserName3

SMS text:

XXXX_D:ALL

Example: 1111_D:ALL

SMS text:

XXXX_T:37011111111 or XXXX_T:UserName

Example: 1111_T:UserName1

NOTE: Only one user name/phone number can be searched at a time.

Autres manuels pour ESIM120

Table des matières

Autres manuels Eldes ouvre-porte

Eldes

Eldes ESIM110 Manuel utilisateur

Manuels ouvre-porte populaires d'autres marques

Elite

Elite CSW200UL Manuel utilisateur

CAME

CAME FROG-PM4 Manuel utilisateur

SOMFY

SOMFY FX230 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Manuel utilisateur

Turnstiles

Turnstiles FSW 900 Manuel utilisateur

Erreka

Erreka BUL BL33 Mode d'emploi

Erreka

Erreka VULCAN S Manuel utilisateur

Beninca

Beninca R1-2 WBV Manuel utilisateur

Erreka

Erreka VULCAN D Manuel utilisateur

Motorline professional

Motorline professional FORT Mode d’emploi

Beninca

Beninca BOB5024 Manuel utilisateur

AGA

AGA GATEMASTER 900 HD Manuel utilisateur

Chamberlain

Chamberlain MotorLift HC280ML Manuel utilisateur

SOMFY

SOMFY Dexxo RTS Pro Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur

Westfalia

Westfalia 85 27 06 Manuel utilisateur

CAME

CAME F500 Manuel utilisateur

Extel

Extel VERA Manuel utilisateur