ELC dmXLAN node1s Manuel utilisateur
dmXLAN node1s User Manual
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
dmXLAN node1s User Manual
The dmXLAN node1s is a single port desk or surface mounted Ethernet to DMX / DMX
to Ethernet node.
This easy to use device will either convert one DMX universe from a lighting desk for
use with an Ethernet network, or provide one DMX universe from an Ethernet
network. The dmXLAN node1s is fully compatible and programmable using the free
ELC dmXLAN software available for download at www.elclighting.com.
The ELC dmXLAN node1s is available in the following variations:
DLN1SF female XLR (5-pin)
DLN1SM male XLR (5-pin)
•Remote programming and monitoring
•Supports sACN, ArtNet & Shownet
•Remote fixture parameter override
•DMX input normal or backup
•DMX output normal, HTP, priority merging, softpatch (channel by channel),
programmable merging with DMX channel control
•RDM Compatible
•Support for WYSIWYG, ESP, Capture
Features
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
Network 10/100 Mbit Ethernet (on Neutrik Ethercon or RJ-45)
The network connection uses a standard UTP network connection.
DMX port pin out
Pin
Description
1
Ground/screen
2
Data –
3
Data +
4
–
5
–
All DMX ports are bi-directional (can act as input or output) with RDM preparation
and internal 120 Ohm terminator resistors.
Mounting
The ELC dmXLAN node1s can be mounted to a wall or surface using the keyhole or
circular hole located on the back of the device.
This product may only be used for
controlling dimmers and moving lights.
Using the product outside of these specifications
will remove all responsibility from the supplier.
Connections
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
The dmXLAN node1s is operated by configuring the device through the dmXLAN
control software. The software can be downloaded from the ELC website at
www.elclighting.com.
Further configuration of the dmXLAN node1s is all done using the single red switch
located on the front of the unit, between the two connections.
This switch can be used in 3 ways;
•Press and hold the switch at power on (when plugging in the PoE source):
this will force the device into boot mode / firmware upgrade mode
•Press the switch (briefly):
this will select the dmXLAN node1s in the active dmXLAN software
•Press and hold the switch for 10 seconds:
this will program the device according to the default settings;
omale XLR version: input universe 0.0
ofemale XLR version: output universe 0.0
Using the dmXLAN software, the DMX port can be programmed to act as input or
output or it can be disabled.
DMX port as output
When a port is set up as a DMX output it can operate in the following modes;
•Disabled the DMX output is disabled
•Outzero the DMX sends out a DMX test signal with all channels at 0%
•Single the output sends out the DMX values of the selected (primary)
Art-Net universe. The DMX output is enabled the first time it detects the DMX
universe on the network (or internal DMX inputs). If the universe on the
network fails, the DMX output will go into DMX hold.
•Dual HTP like single, but merges two DMX universes (primary and
secondary) in highest takes precedence.
•Dual LTP like dual HTP but in latest takes precedence (on a channel by
channel basis).
Menu operation
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
DMX port as input
When a port is set up as a DMX input it can operate in the following modes;
•Disabled the DMX input does nothing
•Normal any valid DMX is sent onto the network (and internal use)
using the selected universe (Art-Net)
Backup the DMX input will not send data if the selected universe is present
on the network. If the selected universe is not present on the network for several
seconds and the input has valid DMX, then it will send DMX data.
If another sender starts sending the same universe, the input will go back into backup
mode.
Power: Power over Ethernet (IEEE 802.3af)
Dimensions: 83 x 75 x 45 mm
Weight: 0.3 kg
Technical specifications
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
Read all instructions - especially the safety requirements - in the user manual before use.
Save these instructions - the safety and operating instructions should be retained for future
reference. Carefully follow all instructions.
Cleaning
Disconnect all connected supply and signal cables before cleaning the unit. Clean with a dry
cloth. Do not use any liquids or aerosols on the unit.
Usage
Do not use the unit near water or moisture. - Do not block any ventilation openings, they are
necessary for the essential airflow within the unit and protect it against overheating. - Install
in accordance with the manufacturer’s instructions. - Do not insert any objects through the
ventilation slots of the unit, as these could come in contact with live parts or could cause
short circuits. This could cause electric shock and/or fire. - Do not install near any heat
sources such as radiators, stoves or other apparatus (including amplifiers) that produce heat.
- Unplug this apparatus during lightning storms or when unused for long periods of time. Do
not place the unit on unstable surfaces.
Servicing
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way such as; damage to the power supply cord or plug, spillage of
liquids, objects falling into the apparatus, exposure to rain or moisture, abnormal operation
or falling damage. In all of the previous conditions, disconnect the main plug immediately
and call your distributor or technical support!
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
General safety instructions
General safety instructions
__________________________________________________________________________________
ELC dmXLAN node1s User Manual
We,
Manufacturers name: ELC lighting b.v.
Manufacturers address: Weerijs 8
5422 WV Gemert
the Netherlands
Herewith take the full responsibility to confirm that the product
Product Category: Lighting control equipment
Name of product: ELC-DLN1SF / ELC-DLN1SM
Which refer to this declaration are manufactured in the Netherlands and complies with the
following product specifications and harmonized standards:
Safety: LVD (Low Voltage Directive) 2014/35/EU, EN62368-1
EMC: 2014/30/EG, EN55032
ROHS (II): 2011/65/EU
With the presumption that the equipment is used and connected according to the manual,
supplied with the equipment. All signal input- and output connections must be shielded and
the shielding must be connected to the ground of the corresponding plug.
Gemert, February 16, 2018
ing. Joost van Eenbergen
Declaration of Conformity
Table des matières
Autres manuels ELC Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
