Elah CHASER 1000 Manuel utilisateur
Owner’s Manual
EL–C1000
All rights reserved, photos and content property of
ÓElah International LLC
Page 2
Table of Contents
Front Cover------------------------------------ 1
Table of Contents---------------------------- 2
Technical Information----------------------- 3
Warning Statement-------------------------- 4
Safety Information--------------------------- 5
Chaser 1000 Parts List-------------------- 6
Tool Kit & Assembly------------------------ 7–10
Seat Installation------------------------------ 10 - 11
Seat Adjustment----------------------------- 11
Installing the Handlebar------------------- 12
Handlebar Adjustment--------------------- 13
Folding the Handlebar -------------------- 13
Charging the Batteries ------------------- 14
Chaser 1000 Operation ------------------- 15
Adjusting the Brakes --------------------- 16
Maintenance --------------------------------- 17
Battery Replacement ------------------- 17
Troubleshooting -------------------------- 18
Warranty -------------------------------- 19
Page 3
Technical Information
Type of Motor 48V Hub Brushless DC Motor
Motor Power 1000W
Battery Type Sealed Lead Acid Battery x4 (48V12Ah)
Charger 100-240VAC50-60HZ，1.8A-2.0A amps
Charging Time 6-8 hours
Rated Speed 33km/h ---38km/h (23.6 mph)
Single Charge distance Up to 35KM (21.75 miles)
Maximum Capacity 158kg (350lbs)
Unit Net Weight 1000W/48V12Ah lead acid battery 64KG (141lbs)
*Note: Speed and distance may vary depending upon the road condition and
weight load.
Page 4
Warning Statement
STOP ----- IMPORTANT!
Before you ride your Chaser 1000, please read this carefully:
Your existing insurance policy may not provide coverage for your
Chaser 1000 or electric vehicles. You should contact your insurance
company to confirm if coverage is provided.
Please do not ride your Chaser 1000 until you have read this owner’s
manual completely and you fully understand all its contents. This
manual contains critical information for your safety. If you have any
questions about the safe operation of your Chaser 1000, you should
contact your authorized dealer.
It is very important that you follow all the safety instructions within this
manual to ensure maximum safety.
Failure to comply with all the standards outlined in this manual could
result in fire/ or serious injury.
Authorized dealers will not be liable for any damage or injuries
caused by unsafe or faulty assembly or unauthorized repairs. Any
repairs carried out by unauthorized service technicians are the sole
responsibility of the owner and the Warranty becomes void.
Our Chaser 1000 range of products is designed to be ecologically
conscious, please dispose of used batteries in compliance with local
laws.
If you are using your Chaser 1000 outdoors, please be aware of all state
and local laws governing the use of such vehicles. State and local
ordinances may vary, and you must make sure you comply with all
applicable laws.
Page 5
Safety Information
Before riding your Chaser 1000, please read and be sure you understand this
manual completely. The Chaser 1000 is not a toy and should always be operated
safely. Elah International LLC will not be liable for any damages or injuries to any
person. Any questions you may have about the safe operation of your Chaser
1000 should be directed to your authorized dealer.
Failure to comply with the safety warnings and operating instructions included in
this manual could result in serious injury to the operator and others.
The Chaser 1000 is not designed for end user repairs. An authorized Chaser
1000 repair technician should carry out repairs. We will not be liable for any
damage or injuries due to repairs by unauthorized individuals.
The Chaser 1000 should only be operated by individuals 16 years of age or
older. The Chaser 1000 is not a toy and should always be used responsibly.
Safety Instructions
ü Always wear approved safety equipment when operating the Chaser 1000
ü Observe the maximum weight capacity of 350lbs
ü Only one person should ride the Chaser 1000 at a time.
ü The Chaser 1000 should always be operated safely under safe conditions.
ü Before riding, inspect the Chaser 1000 to ensure all quick releases and
pivot points are secured properly. Make sure the handlebars are secured
and the hand brake is in operating condition.
ü Check the battery to ensure it is properly charged.
ü The power ignition must be off when charging.
ü Remove your Chaser 1000 from charge once it is charged. Do not
leave the charger plugged in any longer than 8 hours.
ü Charge the battery when only the low power mark is illuminated on the
display.
ü Do not expose the Chaser 1000, batteries, or charger to wet conditions.
ü Always drive on paved surfaces.
ü Be careful when riding on wet or uneven surfaces.
Always wear a helmet when riding the Chaser 1000
Page 6
Chaser 1000 Parts List
1. Front Wheel
2. Disc Brake
3. Electric motor
4. Headlight (pod)
5. Front fork
6. Basket
7. Folding Handlebar Connection
8. Ignition Key (pod)
9. Throttle
10. Headlight Switch
11. Green Button for Horn
12. Handlebar height adjustment
13. Power Indicator (pod)
14. Seat Post
15. Seat Height Adjustment
16. Handbrake
17. Safety Wheels
18. Rear Wheels
19. Battery Cover
20. Electrical Connectors
Page 7
Tool Kit
Charger
Assembling the Chaser 1000
1.) Unpack the Chaser 1000 and inspect all the parts to ensure all are
included.
Tool
Kit
Page 8
2.) Place your Chaser 1000 on a flat, clean surface. Place a block 3.5”
under the front, by the battery. This will make it easier for the next
step.
3.) Remove the Battery Cover at the base of the scooter. Unscrew the
two bolts at the end of the base.
Page 9
4.) Once the cover is removed, locate the Red Inline Fuse Folder. Insert
the Green 30 AMP blade fuse into the Red Inline Fuse Folder. Tuck
the wires without pinching and reinstall.
5.) After reinstalling, the battery pack put the base cover back on and re-
screw the bolts to the appropriate holes.
6.) Connecting the neck to the base - Remove the bolts and nuts from the
connecting tube clamp. Place the connecting tube into the top opening.
Align the bolt holes.
7.) Slide the two bolts through the holes connecting the tube and neck.
Twist the bolts, do not hammer them through.
Page 10
8.) Tighten the bolts and nuts using the wrenches in the tool kit. Also,
tighten the small bolts on the outside of the tube clamp securely.
9.) To assemble the seat, make sure that the parts needed are in your
possession (backrest, seat, seat post, and backrest railing.) Next,
unscrew the bolts in the backrest cushion and seat cushion. Next,
screw the post to the seat cushion and the railing to the backrest.
Seat Installation
Ce manuel convient aux modèles suivants
1
Table des matières
Manuels Scooter populaires d'autres marques
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Manuel utilisateur
Carrera
Carrera impel Manuel utilisateur
Afikim
Afikim Superlight SL-3 Manuel utilisateur
CareCo
CareCo ZOOM Manuel utilisateur
Douglas
Douglas Vespa G.S. Manuel utilisateur
Gazelle
Gazelle with BOSCH System Manuel utilisateur