Ekwb EK-Pro GPU Quick Disconnect Kit Manuel utilisateur

INSTALLATION MANUAL

EK-Pro

GPU Quick Disconnect Kit

GPU WATER BLOCK

- 2 -

This product is compatible with all EK water blocks and manifolds. It is

intended for installation by expert users only. Please consult with

a qualiﬁed technician since improper installation may result in damage

to the equipment. EK assumes no liability whatsoever, expressed

or implied, for the use of these products, nor their installation. The

following instructions are subject to change without notice. Please visit

our website at www.ekwb.com for updates. Before the installation of

this product, please read important notice, disclosure, and warranty

conditions printed on the back of the box.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning with the

installation process.

Remove your graphics card from the computer for the safest

mounting process and to prevent any possible damages to your

GPU or its circuit board (PCB).

EK Fittings require only a small amount of force to screw them

ﬁrmly in place since the liquid seal is ensured with the rubber

O-ring gaskets.

The use of quality market-proven corrosion-inhibiting coolants

is always strongly recommended for any liquid cooling system.

Do not use pure distilled water as a cooling liquid! For best

results, EK recommends the use of EK-CryoFuel Coolants.

- 3 -

TABLE OF CONTENTS

PREPARING THE WATER BLOCK 4

REMOVING THE TERMINAL 4

MOUNTING THE NEW TERMINAL 4

MOUNTING THE BARB FITTINGS 5

MOUNTING THE ZMT TUBE 5

MEASURING TUBES 6

SUPPORT AND SERVICE 8

SOCIAL MEDIA 8

- 4 -

PREPARING THE WATER BLOCK

STEP 1

REMOVING THE TERMINAL

Remove all encircled screws using the 2.5mm Allen key and clean

the mounting surface of the water block with a nonabrasive cloth. EK

recommends you use a dry cloth only.

STEP 1

STEP 2

MOUNTING THE NEW TERMINAL

After you have cleaned the sealing surface, assemble the terminal,

as shown in the picture. Make sure that O-rings are correctly placed

into terminal channels. Once the terminal is in the right position on

the water block, insert and tighten the screws with a 2.5mm Allen key

and apply not more than 0.5 - 0.7 Nm of torque to avoid damaging

the water block. EK recommends this installation is done by

expert users only.

STEP 2

OR 15x1

EPDM50

M4x10 DIN7984

M4x28 DIN7984

- 5 -

STEP 3

MOUNTING THE BARB FITTINGS

Once the terminal is in the position and adequately screwed-in,

screw the barb ﬁttings into the G1/4 threaded holes. For tightening,

use a fork wrench 18 with torque adjustment set to 0.8 Nm.

STEP 3

STEP 4

MOUNTING THE ZMT TUBE

For proper installation of ZMT tubes and clamps, EK recommends

the use of adequate hose clamp pliers.

- 6 -

STEP 5

MEASURING TUBES

When measuring the tube length, make sure to avoid any sharp

transitions of the tube to the barb fittings. Take a look at the

illustration for better understanding.

CORRECT

WRONG

Once the ZMT tubes and clamps are mounted, make sure they are

positioned correctly (as shown in the picture).

STEP 5

- 7 -

ADDITIONAL NECESSARY TOOLS

Hose Clamp Pliers

O-Ring OR 15x1

EPDM50 2 pcs

QD2-FS06-P -

Female QDC 2 pcs

TOP Acetal - FC

Terminal M4 Pre-

Filled1 pc

M4x10 DIN7984

Screw 2 pcs

M4x28 DIN7984

Screw 1pcs

BOX CONTENTS

Check the box contents carefully. The O-rings might already be installed

inside the terminal.

QD2-MSG4 - Male

QDC 2 pcs

2.5 mm Allen Key

1 pc

EK-HFB Fitting 6mm

2 pcs

Hose Clamp FSB

Mini 4 pcs

EK-Tube ZMT 6.5/9.5

Matte Black 1,2 m

In case you need assistance, please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ekwb Accessoires informatiques

ekwb

ekwb EK-XRES Glass Revo D5 Series Manuel

ekwb

ekwb EK-FC Titan SE Series Manuel

ekwb

ekwb EK-FC 6970 V2 Mode d’emploi

ekwb

ekwb EK-XRES D5 Series Manuel

ekwb

ekwb EK-FC GV100 PRO Manuel utilisateur

ekwb

ekwb EK-FC R9-285 Series Manuel

ekwb

ekwb EK-FB Manuel

ekwb

ekwb EK-DCP Manuel

ekwb

ekwb EK-FC970 GTX Series Manuel

ekwb

ekwb EK-FB ASUS Strix X470 RGB Series Manuel utilisateur

ekwb

ekwb EK-FB ASUS M9A Monoblock Series Manuel utilisateur

ekwb

ekwb EK-FC7970 Series Manuel

ekwb

ekwb EK-FC 5870 Series Manuel

ekwb

ekwb EK-Quantum Surface P360M Manuel utilisateur

ekwb

ekwb EK-Supremacy EVO RGB Manuel utilisateur

ekwb

ekwb EK-FC R9-290X DCII Original CSQ Series Manuel

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Manuel utilisateur

ekwb

ekwb EK-Quantum Vector D-RGB Upgrade Kit Manuel utilisateur

ekwb

ekwb EK-Supreme HF Series Manuel

ekwb

ekwb EK-Supremacy MX Series Manuel utilisateur

ekwb

ekwb EK-FC6990 Manuel

ekwb

ekwb EK-RAM Monarch Series Manuel utilisateur

ekwb

ekwb EK-FC Titan X Pascal Series Manuel utilisateur

ekwb

ekwb EK-FC Radeon Vega Strix Series Manuel utilisateur

Manuels Accessoires informatiques populaires d'autres marques

Motorola

Motorola ATRIX Manuel utilisateur

HP USB Media Docking Station Manuel utilisateur

Cherry

Cherry B.UNLIMITED 3.0 Manuel utilisateur

Logitech

Logitech IO2 Manuel utilisateur

ARM

ARM DSTREAM-ST Manuel utilisateur

Bartec

Bartec TC 7 Series Manuel utilisateur

Philips

Philips SPC3540 Manuel utilisateur

Logitech

Logitech mk220 Manuel utilisateur

SilverStone

SilverStone LC02 Manuel utilisateur

Flexispot

Flexispot ML2B Manuel utilisateur

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manuel utilisateur

Adam Equipment

Adam Equipment RS-485 Manuel utilisateur

Vivo

Vivo MOUNT-KB05-4DW Manuel utilisateur

Kvaser

Kvaser Memorator Professional Manuel utilisateur

DRC

DRC D-Imaging Manuel utilisateur

Sven

Sven Base 305 сombo Manuel utilisateur

Hama

Hama 108310 Manuel utilisateur

SpeechWare

SpeechWare FlexyMike FMK03 Manuel utilisateur

ekwb EK-Pro GPU Quick Disconnect Kit Manuel utilisateur

Manuels Accessoires informatiques populaires d'autres marques