Eiki EIP-X350 Manuel utilisateur
MULTIMEDIAPROJECTOR
MODEL EIP-X350
OWNER’S MANUAL
EN-1
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the instructions. If such changes or modifications should be made, you could be
required to stop operation of the equipment.
ModelNumber : EIP-X350
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)
EN-2
Safety Instructions
Read all of these instructions before you operate your projector and save for future
reference.
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
0.7'(20cm)
1.5'(50cm) 3'(1m) 1.5'(50cm)
SIDE and TOP
REAR
Allowing the proper amount of space on the top, sides, and rear of the projector
cabinet is critical for proper air circulation and cooling of the unit. The dimension
shown here indicate the minimum space required. If the projector is to be built into
a compartment or similarly enclosed, these minimum distances must be maintained.
A
n appliance and cart combination should
b
e moved with care. Quick stops,
e
xcessive force, and uneven surfaces
m
ay cause the appliance and cart
c
ombination to overturn.
EN-3
1. Check that the operating voltage of your unit is identical with the voltage of your
local power supply.
2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it
checked by the qualified personnel before operating it further.
3. Do not attempt to service this product yourself, as opening or removing covers may
damage the components inside and will void your warranty.
4. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
5. Unplug the unit from the wall socket if it is not to be used for several days. To
disconnect the cord, pull it out by the plug. Never pull the cord itself.
6. The wall socket should be near the unit and easily accessible.
7. Do not place the projector where the cord can be stepped on as this may result in
fraying or damage to the lead or the plug. Be alert to tripping hazards.
8. Never look into the projector lens when the lamp is switched on as the bright light
can damage your eyes. Never let children look into the lens when it is on.
9. Do not place your hand or objects near the ventilation holes. The air coming out is hot.
10. Never open any covers on the projector except the lamp cover. Dangerous electrical
voltages inside the projector can cause severe injury. Except as specifically directed
in this User’s Manual, do not attempt to service this product yourself. Refer all
servicing to qualified service personnel.
11. Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
12. Keep the plastic packing materials (from the projector, accessories and optional
parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.
13. For ventilation reasons, the fan continues to operate after the projector has been
powered off. Please do not unplug the power cord until the fan stops.
14. The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust). Do not block or place anything near these slots, or internal heat build-up
may occur, causing picture degradation or damage to the projector.
15. When you replace the projector lamp, never touch the new bulb with your bare
hands. The invisible residue left by the oil on your hands may shorten the bulb life.
Use lint-free gloves or finger cots are recommended.
EN-4
16. The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
17. Do not overload wall outlets, extension cords, or integral convenience receptacles
as this can result in a risk of fire or electric shock.
EN-5
CONTENTS
Introduction ............................................................................................................... 6
Projector Features ............................................................................................. 6
Package Contents .............................................................................................. 7
Projector Overview ........................................................................................... 8
Using the Product ................................................................................................... 10
Control Panel ................................................................................................... 10
Terminals ......................................................................................................... 11
Remote Control ................................................................................................ 12
Installing the Batteries ...................................................................................... 13
Notes on AC Power Cord ................................................................................. 14
Remote Control Operation ................................................................................ 15
Installation ............................................................................................................... 16
Connecting the Projector .................................................................................. 16
Powering On/Off the Projector ........................................................................ 17
Adjusting the Projector .................................................................................... 18
Menu Operation ...................................................................................................... 21
Setup Menu ..................................................................................................... 22
Picture Menu .................................................................................................... 23
Source Menu ................................................................................................... 25
Help Menu ........................................................................................................ 25
Maintenance ........................................................................................................... 26
Cleaning the Lens ............................................................................................ 26
Cleaning the Projector Housing ........................................................................ 26
Replacing the Lamp .......................................................................................... 27
Specifications ......................................................................................................... 29
Appendix ................................................................................................................ 30
LED Indicator Messages .................................................................................. 30
Compatibility Modes ......................................................................................... 31
Troubleshooting ............................................................................................... 32
EN-6
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.7" Texas Instruments DLP®technology
XGA (1024 x 768 pixels) real resolution
Auto image re-sizing (Auto-Sync.) to 1024 x 768 full screen with scaling compression
compatibility for VGA, SVGA, XGA and SXGA*
Compatibility with Macintosh®computers
Compatibility with NTSC, PAL, SECAM, and HDTV
Multi-function remote control
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display (OSD)
Advanced electronic keystone correction
* means compressed.
EN-7
Package Contents
When you unpack the projector, make sure you have all these components:
Projector with Lens Cap AC Power Cord VGA Cable (D-SUB to D-SUB)
Composite Video Cable
Owner’s Manual
Remote Control (IR)
Laser Page up
Page down
Hide
Resync
Quick Start Guide
AAA size batteries for
remote control
Save the original shipping carton and packing material; they will come
in handy if you ever to ship your unit. For maximum protection, repack
your unit as it was originally packed at the factory.
Audio Cable
Projector Carrying Case
S-Video Cable
EN-8
Projector Overview
Front View
1 Lens cap
2 Lens cap strap
3Elevator foot
4 Front IR remote control
sensor
5 Elevator button
3 4 6 87
910
11
12 12
51 2
6Projection lens
7 Focus ring
8 Tilt-adjustment foot
9 Control panel
10 Zoom ring
11 Speaker
12 Ventilation holes
EN-9
1 2 3
4
5
75 6
Rear View
1 Rear IR remote control sensor
2 Terminals
3 Main power switch
4 AC power socket
5 Tilt-adjustment foot
6Ventilation holes
7Kensington lock
2
1
2
2
This projector can be used with a ceiling mount for support. The ceiling
mount is not included in the package.
Bottom View
1 Lamp cover
2Ceiling mount
Table des matières
Autres manuels Eiki Projecteur
Eiki
Eiki HDT700 Manuel utilisateur
Eiki
Eiki LC-350 Guide de configuration
Eiki
Eiki LC-WGC500A Manuel d'installation et d'exploitation
Eiki
Eiki LC-XNB5MS Manuel utilisateur
Eiki
Eiki ENT 0 Manuel utilisateur
Eiki
Eiki LC-4300U Guide de configuration
Eiki
Eiki LC-100 Manuel utilisateur
Eiki
Eiki 3850A Manuel utilisateur
Eiki
Eiki IK-1 Manuel utilisateur
Eiki
Eiki Xenon ARC EX-1500 Manuel utilisateur
Eiki
Eiki LC-XL200A Manuel utilisateur
Eiki
Eiki LC-SVGA870U Guide de configuration
Eiki
Eiki EK-500U Manuel utilisateur
Eiki
Eiki LC-X800 Manuel utilisateur
Eiki
Eiki LC-SD12 Manuel utilisateur
Eiki
Eiki LC-HDT700 Manuel d'installation et d'exploitation
Eiki
Eiki 392 Manuel utilisateur
Eiki
Eiki EIP-UJT100 Manuel utilisateur
Eiki
Eiki LC-XGA980E Guide de configuration
Eiki
Eiki LC-NB3EU Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
Christie
Christie LHD700 Manuel utilisateur
