EELP SWXEH-EA Manuel utilisateur
SWXEH-EA
INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Disconnect power before performing work on electrical equipment.
3. Do not use outdoors.
4. Do not let power cords touch hot surfaces and do not mount near gas or electric heaters.
5. Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush with fresh
water and contact a physician immediately.
6. Equipment should be mounted in locations and at heights where unauthorized personnel will not readily subject it to tampering.
7. The use of accessory equipment not recommended by EELP may cause an unsafe condition,
and will void the unit’s warranty.
8. Do not use this equipment for other than its intended purpose.
9. Servicing of this equipment should be performed by qualified service personnel.
10. SAVE THESE INSTRUCTIONS!
INSTALLATION
WALL MOUNT - SINGLE FACE:
1. Extend unswitched 24 hour ACsupply of rated voltage to junction box or appropriate wiring (supplied by others).
Leave at least eight (8) inches of slack wire. The circuit should not be energized at this time.
2. Removethe exit sign faceplate (Figure 2).
3. Removethe exit sign universal copy kit.
4. Knock out the appropriate mounting pattern and/or wire pass-thru hole on the exit back plate to fit the junction box or wiring
connector being used (supplied by others).
5. Bring wires through theback of the sign and mount the exit securely in place. Screw directly to junction box if possible.
6. Connect AC supply per diagram provided (Figure 5). Insulate unused wire!
CAUTION! - Failure to insulate unused wire may result in ashock hazard or unsafe condition as well as equipmentfailure.
7. Route wires and secure them in place.
8. Removeany directional chevron arrows to be indicated as requiredfrom the exit stencil.
9. Remove red fibre, peel back off double sided tape to secure red fibre.
10. Replace the exit faceplate together with red fibre.
11. Turn on theACvoltage supply.
CEILING/END MOUNT - SINGLE OR DOUBLE FACE:
1. Follow steps 1to3of Wall Mounting instructions above.
2. If double face is required then remove thebackplatecover screwandslide the backplate down and out from exit frame. Exit signs
that are specified double face will already have thesecond/rear faceplate installed.
3. On thetop and both sides of the exit there are three(3) holes for the canopy -two (2) for the mounting screws and
one (1) wirepass-thru hole. Knock out thethree appropriate canopy mounting holes for your installation (Figure 3).
4. Securethe canopy to theexit sign using the supplied 1 inch screws and washer nuts and the snap wire pass-thru hole plastic
bushing intothe wirepass-thru hole in the centreof the canopy (Figure 3).
5. Bring wires through thewirepass-thru and connect ACsupply as described in step 6 of Wall Mounting instructions
above.
6. Securethe exit tothe wall or ceiling using thesupplied 1 1/2 inch screws and nuts. Screw directly to junction box if
possible. A universalspider plate is suppliedto allow for exit sign placement adjustment or connection to a variety of electricalboxes
(Figure 4).
7. For double face exits install the second/rear faceplate.
8. Follow steps 7to 10 of Wall Mounting instructions above.
SELF-POWERED:
1. For models EA-EM, plug the battery into the circuit board per (Figure 5) self-powered sign.
926000185 04/14/2010
MAINTENANCE
1. Code requires that the equipment be tested every 30 days for 30 seconds, and that written records be maintained. Further, the equipment is to
be tested once a year for 90 minutes duration as per Code. The equipment is to be repaired whenever the equipment fails to operate as
intended during the duration test. Written records of test results and any repairs made must be maintained. EELP strongly recommends
compliance with all Code requirements.
2. Clean exit face(s) on a regular basis.
NOTE: The servicing of any parts should be performed by qualified service personnel only. The use of replacement parts not furnished by
EELP, may cause equipment failure and will void the warranty.
SAVE THESE INSTRUCTIONS
Chassis GND LED Board
AC ONLY SIGN
Chassis GND
GREEN Ground
BLACK 120VAC
RED 347VAC or ORANGE 277VAC
WHITE Neutral
LED Board
AC & UNIVERSAL DC SIGN
YELLOW
Positive 6 to 24VDC
PURPLE Negative
Emergency Supply
FROM Battery Pack
SELF-POWERED SIGN
Chassis GND
24 hours
Unswitched Supply
GREEN Ground
BLACK 105 to 360V
AC
WHITE Neutral
LED Board
DUAL UNIVERSAL AC SIGN
From Generator OR
Emergency Supply
BROWN 105 to 360VAC
BLUE Neutral
NOTE: Cap unused AC Wire!
NOTE: Cap unused AC Wire!
24 hours
Unswitched Supply
GREEN Ground
BLACK 120VAC
RED 347VAC or ORANGE 277VAC
WHITE Neutral
24 hours
Unswitched Supply
Chassis GND LED Board
NOTE: Cap unused AC Wire!
GREEN Ground
BLACK 120VAC
RED 347VAC or ORANGE 277VAC
WHITE Neutral
24 hours
Unswitched Supply
Ni-Cd
Battery
Figure 4
Figure 1 Frame
Faceplate
Figure 2
Figure 3
Figure 5
Ceiling
Mount
End Wall
Mount
Remove chevrons/
arrows as required
Universal
Spiderplate
Electrical Junction Box
(supplied by others)
Install canopy kit as shown
if required
926000185 04/14/2010
Autres manuels EELP Équipements de sécurité
Manuels Équipements de sécurité populaires d'autres marques
Innova
Innova Xtirpa Mode d’emploi
bolle SAFETY
bolle SAFETY B810 Manuel utilisateur
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur
Hiltron security
Hiltron security POWER8E Mode d’emploi
Hatco
Hatco B-950P Manuel utilisateur
Sitec
Sitec TX MATIC Manuel utilisateur
