Edimax IC-7010PTn Guide de configuration
How to setup wireless function of Edimax IP Camera
The wireless function of Edimax IP Camera is disabled by default. You need to hardwired the camera by Ethernet
cable to connect the camera to your network first.
Introduction
For any new wi-fi devices (wireless computers, Edimax wireless camera, iPhone, Android) to join a Wi-Fi network, you need to know
two things about your Wi-Fi network.
1. The SSID is the name of the wireless network.
2. The wireless encryption password of the wireless network.
If you have no idea above the above two, you need to check your wireless router’s setting and find them out.
Procedures
Step 1. We recommend you assign a static IP address to IP camera, therefore, you’d better
know the IP addresses used in your network.
1. Go to a computer which connects to your network as usual. Hardwired computer is
preferred.
2. For Windows XP, click on Start, click on Run. Enter “cmd” hit OK.
For Windows 7/Windows Vista, click on Start, go to “Search programs & files”, enter “cmd”
hit OK.
3. In the command prompt window, enter “ipconfig” hit Enter. Locate the IP v4 address,
subnet mask, and default gateway.
4. You can minimize the command prompt. The command prompt will be used later.
In above example, the computer has IP 192.168.0.100 while the wireless router is 192.168.0.1.
Step 2. Install the IP Camera software from CD disk.
Step 3. We are going to change the IP address to Edimax camera to fit with our network.
Open the IPCam Admin utility. The default IP address of camera is 192.168.2.3. We are going
to change it to 192.168.0.10.
Click on “Configure camera”. Enter the password ‘1234’. Click Ok.
The default IP is 192.168.2.3. We enter the a new IP 192.168.0.10, Gateway 192.168.0.1, and
DNS server 192.168.0.1.
Step 4. Open Internet Explorer or other browser. Enter the IP address of Edimax Camera.
Login with username admin and password 1234.
If it prompts to install an ActiveX, click on Run Add-On.
Step 5. Go to Network, go to WLAN. Click on the circle for Enable Wireless Connection.
It shows all the available wireless networks near the camera. You should see the SSID of your
wireless network.
You may want to pay attention about the Signal and Encryption for your wireless network.
Click on the circle in front of the SSID of your wireless network to connect.
Once you click on the Connect button, its SSID, Authentication/Encryption will be copied to
below table.
Delete all the * in the field of WPA Pre-Shared Key. Enter your WPA pre-shared key of your
wireless network. Please note the pre-shared key is case-sensitive (‘A’ is different than ‘a’).
So please enter the security key carefully. Then press “Apply”.
There is no any message after you click on “Apply”. The screen seems intact. This is normal.
If your wireless network uses WEP encryption, enter your WEP password repeatedly in WEP Key1, WEP Key2,
WEP Key3, WEP Key4. Then press “Apply” button.
Step 6. Get to the command prompt. Use a command called “ping” to ping the IP address of
the camera.
Please note the “-t” at the end of the command. It will do continuously ping until you press
Ctrl + C. The result is like this.
Step 7. Unplug the Ethernet cable from the wireless camera.
The wireless LED on the front of the camera turns on and flashes.
If you see replies from the camera, Congratulations, the camera is attached to your wireless
network successfully.
Press Ctrl + C to stop the PING command. Enter “exit” hit Enter to close the command
prompt.
Go to IE http://IP_address_of_Camera and you should be able to see the camera.
Now you can move the wireless camera to a desired spot with its power adapter. Just power it
on, the camera will connect to your wireless network successfully.
Table des matières
Autres manuels Edimax Caméra de sécurité
Edimax
Edimax IC-9000 Manuel utilisateur
Edimax
Edimax IC-7010 Series Manuel utilisateur
Edimax
Edimax IC-5150W Manuel utilisateur
Edimax
Edimax NC-203 Manuel utilisateur
Edimax
Edimax NS-120 Manuel utilisateur
Edimax
Edimax IC-3116W Manuel utilisateur
Edimax
Edimax IC-1510 Manuel utilisateur
Edimax
Edimax 3Mpx PoE Manuel utilisateur
Edimax
Edimax PT-111E Manuel utilisateur
Edimax
Edimax PT-31E Manuel utilisateur
Edimax
Edimax PT-31 Manuel utilisateur
Edimax
Edimax IC-1520POE Manuel utilisateur
Edimax
Edimax IC-7000PT V3 Manuel utilisateur
Edimax
Edimax Pan/Tilt IP Surveillance Camera IC-7000 Manuel utilisateur
Edimax
Edimax PT-112E Manuel utilisateur
Edimax
Edimax IC-3100 Manuel utilisateur
Edimax
Edimax IR-112E Manuel utilisateur
Edimax
Edimax IC-3005 Series Manuel utilisateur
Edimax
Edimax Network Camera Manuel utilisateur
Edimax
Edimax IC-3110 Manuel utilisateur
