Edimax PS-1206MF Manuel utilisateur

part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic,

mechanical, magnetic, optical, chemical, manual or otherwise,

without the prior written permission of this company.

This company makes no representations or warranties, either

expressed or implied, with respect to the contents hereof and

specifically disclaims any warranties, merchantability or fitness for

any particular purpose. Any software described in this manual is

sold or licensed "as is". Should the programs prove defective

following their purchase, the buyer (and not this company, its

distributor, or its dealer) assumes the entire cost of all necessary

servicing, repair, and any incidental or consequential damages

resulting from any defect in the software. Further, this company

reserves the right to revise this publication and to make changes

from time to time in the contents hereof without obligation to notify

any person of such revision or changes.

The product you have purchased and the setup screen may appear

slightly different from those shown in this QIG. For more detailed

information about this product, please refer to the User's Manual on

the CD-ROM. The software and specifications are subject to

change without notice. Please visit our web site www.edimax.com

names mentioned in this manual are trademarks and/or registered

trademarks of their respective holders.

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Warning

Any changes or modifications not expressly approved by the party responsible

for compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall not

be less than 20cm (8 inches) during normal operation.

The antenna(s) used for this transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Radio Frequency Interference Requirements

This device is restricted to indoor use due to its operation in the 2.4 GHz

frequency range. FCC requires this product to be used indoors in 2.4 GHz the

frequency range to reduce the potential for harmful interference to co-channel

Mobile Satellite systems.

RSS-210 Compliance Statement

The term “IC:” before the certification/registration number only signifies that

Industry Canada technical specifications were met. Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may

cause undesired operation of the device.

Transmitter Antenna

To reduce potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated power

(EIRP) is not more than that required for successful communication

This device has been designed to operate with an antenna having a maximum

gain of 5dBi. Antenna having a higher gain is strictly prohibited per regulations

of Industry Canada. The required antenna impedance is 50 ohms.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20cm between the radiator & your body.

This device and its antenna(s) must not be co-located or operating in

conjunction with any other antenna or transmitter.

Country Code Setting Disable

Country Code selection feature to be disabled for products marketed to the

US/CANADA.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC

OF THE EUROPEAN PARLIAMENTAND THE COUNCIL of March 9, 1999 on

radio equipment and telecommunication terminal Equipment and the mutual

recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station

Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who

install and use it. However, special attention must be paid to the dangers of

electric shock and static electricity when working with electrical equipment. All

guidelines of this and of the computer manufacture must therefore be allowed

at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in UK,

Ireland, Germany, France, Spain, Portugal, Italy, Austria, Switzerland, Belgium,

Netherlands, Luxemburg, Denmark, Finland, Norway, Sweden, Poland,

Hungary, Czech, Slovakia, Latvia, Lithuania, Estonia, Slovenia, Greece,

Romania, Bulgaria

EU Countries Not intended for use

None.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause

radio interface, in which case the user may be required to make adequate

measures.

A CE declaration of conformity is available on www.edimax.com

Regulatory Approvals for AC Adapter

Input:

AC 100-240 V, 50-60 Hz

Output:

DC 5V, 1.0A

Power Consumption:

300mW

Safety Standards: UL/CUL 60950-1

EMC:

FCC part 15 subpart B Class B

Safety Information

For your safety, be sure to read and follow all warning notices and instructions.

•Do not continue operating if you notice smoke or unusual odors or sounds.

Continued operation may result in electric shock or fire. Immediately turn

off power and remove the power adapter from the outlet, then contact

EPSON.

•Do not disassemble or modify the product in any way (unless described in

instructions). Doing so may cause injury or electric shock.

•Make sure you use the power adapter supplied with the MFP Server. Use

of a different power adapter could damage the MFP Server.

•Do not handle plugs with wet hands. Doing so may result in electric shock.

•Do not use damaged power cords. Doing so may result in electric shock

and fire. Observe the following when handling power cords:

•Do not modify power cords.

•Do not place heavy objects on power cords.

•Do not sharply bend, twist, or pull on power cords.

•Do not route power cords near heating equipment.

•Do not attempt to repair the power adapter or cord. Contact EPSON to

order a new one.

•Handle power plugs with care. Improper handling may result in fire.

Observe the following when handling power plugs:

•Do not plug in power plugs that are dusty or dirty.

•Firmly plug in power plugs all the way.

•Periodically remove power plugs from the outlet and clean the base of the

plug. If power plugs are left plugged into an outlet for long periods, dust

may accumulate near the base, posing a risk of short-circuiting and fire.

•To ensure safety, always unplug power adapter from the outlet when the

product will not be used for an extended period.

•Make sure to connect the cables to the correct ports.

•Place connecting cables carefully so that no one will step on them or

stumble over them.

•Avoid locations that are subject to rapid changes in heat or humidity,

shocks or vibrations, or dust.

•Do not expose the device to dampness, dust or corrosive liquids.

•Discontinue use if a foreign object or water or other liquid enters the

product. Continued use may result in electric shock and fire. Immediately

remove the power adapter from the outlet and then contact EPSON.

Contents

1. Introduction......................................................................1

2. MFP Server Modes..........................................................2

3. Using Your All-in-one in MAC...........................................4

3.1 Printing.............................................................................6

3.2 Scanning..........................................................................7

3.3 Reading Memory Cards...................................................9

4. MFP Manager in MAC...................................................10

4.1 MFP Server List .............................................................10

4.2 Option Settings ..............................................................13

4.2.1 General Setting .................................................................13

4.2.2 Search for MFP Server......................................................14

5. Server Configuration in MAC.........................................15

5.1 Introduction....................................................................15

5.2 Search for All Available MFP Server ..............................16

5.3 Status of MFP Server.....................................................17

5.4 General Setting..............................................................19

5.5 TCP/IP Configuration.....................................................21

5.6 System Configuration.....................................................22

5.7 Wireless Configuration...................................................23

6. Web Management .........................................................29

6.1 Introduction....................................................................29

6.2 Login..............................................................................30

6.3 Device Status.................................................................31

6.3.1 System Status ...................................................................31

6.3.2 Printer Status.....................................................................32

6.3.3 TCP/IP Status....................................................................33

6.4 Setup Wizard .................................................................34

6.4.1 System ..............................................................................34

6.4.2 Wireless ............................................................................37

6.4.3 TCP/IP...............................................................................44

6.4.4 Save Settings....................................................................45

6.5 System Tools..................................................................46

Autres manuels pour PS-1206MF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edimax Serveur d'impression

Edimax

Edimax PS-1206P Manuel utilisateur

Edimax

Edimax Combo Print Server Manuel utilisateur

Edimax

Edimax PS-3207U Manuel utilisateur

Edimax

Edimax PS-1206UWg Manuel utilisateur

Edimax

Edimax PS-1206MF Manuel utilisateur

Edimax

Edimax PS-3103P Manuel utilisateur

Edimax

Edimax PS-1206PWg Manuel utilisateur

Edimax

Edimax PS-1206MF Manuel utilisateur

Edimax

Edimax PS-1206PWg Manuel utilisateur

Edimax

Edimax PS-2207SU Manuel utilisateur

Edimax

Edimax PS-3207 Series Manuel utilisateur

Edimax

Edimax PS-901 Manuel utilisateur

Edimax

Edimax PS-1100+ Manuel utilisateur

Edimax

Edimax PS-2207SUg Manuel utilisateur

Edimax

Edimax PS-3103P Manuel utilisateur

Edimax

Edimax Print Server Manuel utilisateur

Edimax

Edimax PS-2207SU Manuel utilisateur

Edimax

Edimax PS-1206UWg Manuel utilisateur

Edimax

Edimax PS-2207SU Manuel utilisateur

Edimax

Edimax Print Server Manuel utilisateur

Edimax

Edimax PS-1210Un Manuel utilisateur

Edimax

Edimax PS-1203 Manuel utilisateur

Edimax

Edimax Past Ethernet Combo Print Server PS-1216U Manuel utilisateur

Edimax

Edimax PS-1210Un Manuel utilisateur

Manuels Serveur d'impression populaires d'autres marques

Digitus

Digitus DN-13003-1 Manuel utilisateur

Intellinet

Intellinet 509077 Manuel utilisateur

Atlantis Land

Atlantis Land NETSERVER A02-PSU_GX02 Manuel utilisateur

Buffalo

Buffalo LPV4-U2-300S Manuel utilisateur

Zonet

Zonet ZPS1000 Manuel utilisateur

TRENDnet

TRENDnet TEW-P11G Manuel utilisateur

Axis

Axis 140 BJC Manuel utilisateur

HP Jetdirect 280m - 802.11b Wireless Print... Manuel utilisateur

MicroNet

MicroNet SP766W Manuel utilisateur

NETGEAR

NETGEAR PS104 - Hub - EN Manuel utilisateur

Axis

Axis AXIS 1610 Manuel utilisateur

Buffalo

Buffalo LPV4-U2-300S Manuel utilisateur

Axis

Axis 5600+ Manuel utilisateur

LevelOne

LevelOne WPS-9123 Manuel utilisateur

NETGEAR

NETGEAR PS105 Manuel utilisateur

Xerox

Xerox FreeFlow Print Server V9 SP3 Manuel utilisateur

SEH

SEH primos Manuel utilisateur

D-Link

D-Link DP-101P+ Manuel utilisateur