Edimax AR-7188WnA Manuel utilisateur
AR-7188WnA
Quick Installation Guide
04-2014 / v1.0
1
COPYRIGHT
Copyright Edimax Technology Co., Ltd. all rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission from
Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties,
either expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability, or fitness for any
particular purpose. Any software described in this manual is sold or licensed
as is. Should the programs prove defective following their purchase, the
buyer (and not this company, its distributor, or its dealer) assumes the entire
cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Edimax Technology Co.,
Ltd. reserves the right to revise this publication and to make changes from
time to time in the contents hereof without the obligation to notify any
person of such revision or changes.
The product you have purchased and the setup screen may appear
slightly different from those shown in this QIG. For more information about
this product, please refer to the user manual on the CD-ROM. The software
and specifications are subject to change without notice. Please visit our
website www.edimax.com for updates. All brand and product names
mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Edimax Technology Co., Ltd.
Add: No. 3, Wu-Chuan 3rd Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan
Tel: +886-2-77396888
Email: sales@edimax.com.tw
2
M
Mu
ul
lt
ti
i-
-L
La
an
ng
gu
ua
ag
ge
e
Q
Qu
ui
ic
ck
k
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
G
Gu
ui
id
de
e(
(Q
QI
IG
G)
)
o
on
n
t
th
he
e
C
CD
D
Č
e
eš
št
ti
in
na
a
: Českého průvodce rychlou instalací naleznete na přiloženém CD s
ovladači
D
De
eu
ut
ts
sc
ch
h:
:
Finden Sie bitte das deutsche S.A.L. beiliegend in der Treiber CD
E
Es
sp
pa
añ
ño
ol
l
:Incluido en el CD el G.R.I. en Español.
F
Fr
ra
an
nç
ça
ai
is
s:
:
Veuillez trouver l’français G.I.R ci-joint dans le CD
I
It
ta
al
li
ia
an
no
o:
:
Incluso nel CD il Q.I.G. in Italiano.
M
Ma
ag
gy
ya
ar
r:
:
A magyar telepítési útmutató megtalálható a mellékelt CD-n
N
Ne
ed
de
er
rl
la
an
nd
ds
s
: De nederlandse Q.I.G. treft u aan op de bijgesloten CD
P
Po
ol
ls
sk
ki
i
: Skrócona instrukcja instalacji w języku polskim znajduje się na
załączonej płycie CD
P
Po
or
rt
tu
ug
gu
uê
ês
s
:Incluído no CD o G.I.R. em Portugues
Р
Ру
ус
сс
ск
ки
ий
й:
:
Найдите Q.I.G. на pусскoмязыке на приложеном CD
T
Tü
ür
rk
kç
çe
e:
:
Ü rün ile beraber gelen CD içinde Türkçe Hızlı Kurulum Kılavuzu'nu
bulabilirsiniz
У
Ук
кр
ра
аї
їн
нс
сь
ьк
ка
а:
:
Для швидкого налаштування Вашого пристрою, будь ласка,
ознайомтесь з інструкцією на CD
3
PRODUCT INTRODUCTION
Package Contents
Before you start using this product, please check if there is anything
missing in the package and contact your dealer to claim the missing
item(s):
ADSL2+ router
12V Power adapter
1 meter RJ-45 Ethernet cable
1.8M RJ-11 telephone line x 2
Quick installation guide
CD containing setup wizard, user manual & multi-language QIG
Splitter (Annex A)
5dBi Antenna
System Requirements
Recommended system requirements are as follows.
A 10/100 base-T Ethernet card installed in your PC
A hub or Switch (connected to several PCs through one of the Ethernet
interfaces on the device)
Operating system: Windows 98 SE, Windows 2000, Windows ME,
Windows XP, Windows 7/8/8.1
Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox
1.5 or higher
LED & Button Definitions
Front Panel
4
LEDs
Color
Status
Description
Green
ON
Powered on
OFF
Powered off
Red
ON
ADSL broadband initial self-test failed or upgrading
firmware
ADSL
Green
ON
ADSL line is synchronized and ready to use
SLOW
BLINK
ADSL synchronization failed ( Please refer to Note
1)
FAST BLINK
ADSL negotiation is in progress.
Internet
Green
ON
Internet connected in router mode
BLINK
Internet activity (transferring/receiving data) in
router mode
OFF
Device in bridged mode
Red
ON
Internet not connected in router mode
(Please refer to Note 2)
LAN1~4
Green
ON
LAN port connected
BLINK
LAN activity (transferring/receiving data)
OFF
LAN port not connected
Green
On
The device has successful WLAN connection.
Blinks
Data is being transmitted on WLAN
Off
The WLAN connection is failed
WPS
Green
Off
WPS is disabled
Blinks
WPS is enabled, and is waiting for client to negotiate
Note:
1) If the ADSL LED is off, please check your Internet connection. Refer to A .
Hardware Installation for more information about how to connect the
router correctly. If all connections are correct, please contact your ISP to
check if there is a problem with your Internet service.
2) If the Internet LED is red, please check your ADSL LED first. If your ADSL
LED is off, refer to Note 1. If the green ADSL LED is ON, please check your
Internet configuration. You may need to check with your ISP that your
Internet is configured correctly.
Rear Panel
5
Items
Description
Power ON/OFF
12V
Power connector
Wireless LAN ON/OFF (Press the button gently and let go after 1 second to
enable WLAN function, and press the button gently and let go after 1 second to
disable.)
WPS
WPS ON/OFF (Press the button gently and let go after 1 second to enable
WLAN function, and press the button gently and let go after 1 second to
disable.)
LAN1~4
Ethernet RJ-45 port 1~4
Reset
Resets device to factory defaults
(to reset to factory defaults, push a paper clip into the hole when the device is
powered and hold for more than 10 seconds)
Line
Line RJ-11 port
6
GETTING STARTED
A. Hardware Installation
Step 1: Connect the ADSL line
Connect the Line interface of the device to the Modem interface of a
splitter using a telephone cable. Connect a telephone to the Phone
interface of the splitter using a telephone cable. Connect the Line interface
of the splitter to your existing, incoming line.
The splitter has three interfaces:
Line: Connect to a wall phone jack (RJ-11 jack).
Modem: Connect to the ADSL jack of the device.
Phone: Connect to a telephone set.
Step 2: Connect the router to your LAN network
Connect the LAN interface of the router to your PC, Hub or Switch using an
Ethernet cable (MDI/MDIX).
Note:
Use twisted-pair Ethernet cables to connect the router to a hub or
switch.
Step 3: Connect the power adapter to the router
Plug one end of the power adapter into a wall outlet and connect the other
end to the 12V interface of the device.
The following diagram shows how to correctly connect the router, PC,
splitter and the telephone sets.
7
Step 4: Check the ADSL LED status
Please check the ADSL LED on the front panel. This light indicates the status
of your ADSL broadband through your telephone line. If the light is on, you
can continue setup. However if the light is flashing, there is no broadband
line detected. Please call your Internet Service Provider (ISP) and inform
them about the flashing ADSL light to resolve the issue.
Step 5: Firewall settings
Please turn off all personal firewalls before you continue the setup –firewalls
can block communication between your PC and router.
Note: You must use the power adapter included in the package with the
router, do NOT attempt to use a third-party power adapter.
Step 6: PC LAN IP configuration
Configure your PC’s LAN settings to automatically obtain an IP address from
the router by following the steps below:
1. Click “Start” and then select “Control Panel”.
2. Click “Switch to Classic View” in the top left to show additional setting
icons.
8
3. Locate the “Network Connections”icon and double-click to open
network connection settings.
4. Select the “Local Area Connection” icon and right-click it to open the
sub-menu, then select “Properties”.
5. Select “Internet Protocol (TCP/IP)” and then click “Properties”
9
6. Ensure that “Obtain an IP address automatically” and “Obtain DNS
server address automatically” are selected and then press “OK”.
B. Internet Connection
You can configure the router by running the setup wizard on the CD-ROM
included in the package contents. The wizard enables you to configure
your Internet connection, upgrade the firmware and change the router’s
password. When you start the setup wizard, you will see the following
screen. Please choose a language and follow the on screen instructions
until setup is complete.
Table des matières
Autres manuels Edimax Routeur réseau
Edimax
Edimax BR-6258n Nano router Manuel d'instructions
Edimax
Edimax BR-6478Gn Manuel utilisateur
Edimax
Edimax ES-1008PH Manuel utilisateur
Edimax
Edimax 3G-6200nL V2 Manuel utilisateur
Edimax
Edimax AR-7064+ Manuel utilisateur
Edimax
Edimax CV-7438nDM Manuel utilisateur
Edimax
Edimax GS-5208P Manuel utilisateur
Edimax
Edimax 3G-6218n Manuel utilisateur
Edimax
Edimax BR-6524n Manuel utilisateur
Edimax
Edimax ES-1008PH Guide de référence
Edimax
Edimax BR-6428nS V2 Manuel utilisateur
Edimax
Edimax BR-6258GNL Manuel utilisateur
Edimax
Edimax Triple A Guide d'installation
Edimax
Edimax BR-6228nS V2 Manuel utilisateur
Edimax
Edimax ES-3124REM Manuel utilisateur
Edimax
Edimax AR-7084A Manuel utilisateur
Edimax
Edimax AR-7211A V2 Manuel utilisateur
Edimax
Edimax BR-6428nS 9dBi Manuel utilisateur
Edimax
Edimax 3G-6200nL V2 Guide de référence
Edimax
Edimax BR-6476AC Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité