Edimax EN-5200PXA Manuel utilisateur
L
A
N
P
R
O
F
E
S
S
I
O
N
A
L
Ethernet Adapter
10Mbps PCI
Ethernet Adapter
EN-5200PXA
EN-5200PLT
User’s Manual
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply
with the limits of a Class B computing devices,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
If you suspect this product is causing interference, turn
your computer on and off while your radio or TV is
showing interference. If the interference disappears
then when you turn the computer off and reappears
then you turn the computer on, something in the
computer is causing interference.
You can try to correct the interference by one or more
of the following measures :
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit
difference from that to which the receiver is
connected.
4. Ensure that all expansion slots (on the back or side
of the computer) are covered. Also ensure that all
metal retaining brackets are tightly attached to the
computer.
1
1Introduction
Thanks you for purchasing our 10Mbps PCI Ethernet
Adapter. This guide is to provide the installation and
usage of this adapter for network installers and users.
This 10Mbps Ethernet network adapter complies to
PCI 2.1 specification and supports half/full duplex
feature which can double network speed.
The jumperless design simplifies the installation of this
adapter. This adapter is complete self-configurable,
requiring no intervention from the user. Just plug in
the card and all setup is done automatically. No more
software to run !
This adapter supplies many drivers including ODI
driver for NetWare 3.x/4.x, NDIS driver for Microsoft
LAN Manager, Windows 95, Windows 98 and
Windows NT, and a Packet Driver for TCP/IP
software.
Whatever your requirements are ease of installation,
superior performance or responsive support backed up
by unlimited technical support, this adapter is the
superior choice.
1
2
2Features & Specifications
(1) Features & Benefits
ŸSupports 32-bit PCI 2.1 Bus high performance.
ŸComplies with the IEEE 802.3 CSMA/CD Standard :
EN-5200PXA - 10Base2/10BaseT
EN-5200PLT - 10BaseT
ŸFull duplex design to double the performance to
20Mbps.
ŸProvides the standard connectors :
EN-5200PXA - RJ-45 and BNC
EN-5200PLT - RJ-45
ŸBuilt-in data prefetch function to improve
performance.
ŸSupport auto-polarity correction for 10BaseT.
ŸOn-board 32K bytes SRAM buffer to speed up data
transmission.
ŸSupports ODI driver for NetWare 3.x/4.x; NDIS
driver for LAN Manager, Windows 95, Windows 98,
Windows NT; Packet Driver for TCP/IP software.
ŸProvides diagnostic software and two LEDs to
indicate network link and activity.
ŸSupports smart remote Boot ROM (optional)
2
(2) Technical Specification
ŸTopology : Bus(EN-5200PXA) and
Star(EN-5200PXA/EN5200PLT)
ŸConnector : EN-5200PXA - RJ45 and BNC
EN-5200PLT - RJ-45
ŸStandard : IEEE 802.3 10Base2 (EN-5200PXA)
IEEE 802.3 10BaseT (EN-5200PXA/
EN-5200PLT)
ŸTransmission Rate : 10Mbps or 20Mbps
ŸHardware Required : IBM compatible PC with
available PCI slot
ŸLED : Link and Activity
ŸIRQ Line : Assigned by system
ŸI/O Address : Assigned by system
ŸDrivers : ODI driver for NetWare 3.x/4.x
NDIS driver for LAN Manager,
Windows 95, Windows 98,
Windows NT, Packet Driver
for TCP/IP software.
ŸTemperature : 00C to 550C (Operating)
ŸHumidity : 10% to 90% (Non-condensing)
ŸCertification : FCC Class A, CE Mark
ŸDimension : EN-5200PXA -
EN-5200PLT - 120 x 63 mm
ŸWeight : EN-5200PXA -
EN-5200PLT - 60 g
ŸPower consumption : EN-5200PXA -
EN-5200PLT - 1.8W (Max.)
3
3
3Installation
(1) Hardware Installation
To insert the network adapter into your PC, follow the
steps bellow :
1. Turn off the computer and remove its cover.
2. Insert the adapter into a PCI slot.
3. Secure this adapter to the rear of the computer
chassis and put back the computer cover.
4. Connect the adapter to the network using twisted-
pair cable or RG-58 coaxial cable(EN-5200PXA
only).
(2) Driver Installation
Use the drivers supplied by the diskette included in this
product. For detail description, please refer to
readme.doc or readme.exe in the diskette provides by
this product.
4
4
4Trouble-shooting
Most common factors that cause an adapter to fail are
configuration conflicts and cabling problems. PCI card
shouldn’t have any conflict problem due the plug and
play specification.
If you experience any problems with the adapter, first
make sure the appropriate driver is loaded, the proper
cable is connected to the adapter port and the hub
complies with the adapter specification, such as
10Mbps 10BaseT, then check the LED.
The adapter provides two LEDs to indicate network
status.
nLink
Monitors the data link status on the cable. It turns ON
when there is data link, and OFF when there is bad
connection.
nActivity
Blinks when there is data transmission/reception.
5
TRADEMARKS
Copyright 1998 by Edimax Technology Co., Ltd. No
part of this manual may be reproduced, transcribed,
stored in a retrieval system, translated into any
language or computer language without the prior
written consent of Edimax.
All brand and product names are trademarks and/or
registered trademarks of their respective companies.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Edimax Adaptateur
Edimax
Edimax BT-8500 Manuel utilisateur
Edimax
Edimax USB 2.0 to Fast Ethernet Adapter With 3-Port USB Hub... Manuel utilisateur
Edimax
Edimax EW-7811UAC Manuel utilisateur
Edimax
Edimax EP-4103DL Manuel utilisateur
Edimax
Edimax Access Point Guide de l'utilisateur
Edimax
Edimax EW-7611UTn Manuel utilisateur
Edimax
Edimax WRL-22824 Manuel utilisateur
Edimax
Edimax EW-7618Ug Manuel utilisateur
Edimax
Edimax HP-5101 Manuel utilisateur
Edimax
Edimax EW-7811UN Manuel utilisateur
Edimax
Edimax HP-5102AC Manuel utilisateur
Edimax
Edimax EW-7106PC Manuel utilisateur
Edimax
Edimax HP-6002 Manuel utilisateur
Edimax
Edimax EP-4203DL Manuel utilisateur
Edimax
Edimax HP-5001 Manuel utilisateur
Edimax
Edimax EW-7317UG Manuel utilisateur
Edimax
Edimax HP-5101AC Manuel utilisateur
Edimax
Edimax EW-7811UAC Manuel utilisateur
Edimax
Edimax HP-5102AC Manuel utilisateur
Edimax
Edimax HP-2002NCK Manuel utilisateur
