Edelbrock 67082 Manuel utilisateur
Catalog #67082, 67083, 67092, 67093
©2006 Edelbrock Corporation
Page 1 of 2 Brochure #63-67082
Rev. 5/06 - DA/mc
®
TUBULAR EXHAUST SYSTEM
Vehicle Applications: See Below
Catalog #67082, #67083, #67092, #67093
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new
Tubular Exhaust System
(TES). If you have any questions, please
contact our Technical Hotline at : 1-800-416-8628 from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at
[email protected]. Please fill out and mail your warranty card.
Applications:
Catalog #s 67082, #67083 - 1996-1997 Chev./GMC S-10, S-15 Pick-Up, 4.3L V6 2WD with Auto Transmission
Catalog #s 67092, #67093 - 1996-1997 Chev./GMC S-10, S-15 Pick-Up, Blazer, Jimmy, 4.3L V6 4WD, Auto Transmission
TUBULAR EXHAUST SYSTEM: These components are designed as a system to improve the exhaust efficiency of the GM C.P.I.
(Central Port Injection) 4.3L V6 engine. A performance gain can be expected by the installation of the system. This system requires
no welding for installation and retains all O.E.M. emissions equipment.
Suggested Tools Needed for Installation: This vehicle has some metric fasteners.
❑ 3/8" ratchet socket set with extensions and universal 13mm and 15mm swivel sockets
❑Combination set of open-end wrenches
❑Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑ Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695)
SPECIAL NOTICE: This Edelbrock Tubular Exhaust System has received an Executive Order number (E.O.#) from the California Air
Resources Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we
have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle for which
it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and engine specifications decal. Do not
cover any part of your original emission decal.
WARNING: The use of "Thermal Wrap" or any aftermarket coating process will void the warranty on your Edelbrock Tubular
Exhaust Systems. Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the system.
NOTE: High temperature spark plug wires and boots are recommended to withstand heat from T.E.S.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in
poor performance and engine or vehicle damage.
INSTALLATION INSTRUCTIONS
DISASSEMBLY
1. Disconnect battery negative cable from battery.
2. Raise vehicle and support with jackstands.
3. Use penetrating oil on all nuts and bolts to be removed.
This will prevent the possibility of broken or stripped nuts
and bolts.
4. Remove O2 sensors and unbolt exhaust crossover pipe
from manifolds.
5. Unbolt and remove crossover pipe assembly.
6. Lower vehicle and remove air cleaner assembly.
7. Remove all spark plugs.
8. Unbolt and remove right side exhaust manifold.
9. Unbolt dipstick bracket from cylinder head, but do not
remove dipstick.
10. Remove EGR tube from left manifold.
11. Remove cross bolt from steering shaft and slide lower
section of shaft down off of upper shaft.
12. Unbolt and remove left exhaust manifold.
13. Remove EGR adapter from left manifold.
ASSEMBLY LEFT SIDE
1. Install EGR adapter in new manifold.
2. Start rear manifold bolt with gasket, lock and flat washer
in place, and screw in leaving just enough space to slide
manifold into position. NOTE: Be sure spark plug clips do
not interfere with manifold surface.
Catalog #67082, 67083, 67092, 67093
©2006 Edelbrock Corporation
Page 2 of 2 Brochure #63-67082
Rev. 5/06 - DA/mc
Edelbrock Corporation, 2700 California St., Torrance, CA 90503
Tech Line: 1-800-416-8628
E-Mail: [email protected]
KIT CONTENTS
Qty. Part # Description
❑125-9447 Header left side
❑125-9446 Header right side
❑125-9521 Extension pipe left side
❑125-9643 Y-pipe assembly
3. Slide manifold into position and start all bolts, using
lock washers on all bolts plus flat washers on slotted
ends (do not tighten). Use ferry bolt and spacer for
radiator hose support bracket.
4. Install EGR tube on manifold.
5. Tighten all bolts at this time.
ASSEMBLY RIGHT SIDE
1. Start rear manifold bolt with gasket, lock and flat
washers in place, then screw in leaving just enough
space to slide manifold into position. NOTE: Be sure
spark plug clips do not interfere with manifold
surface.
2. Place manifold into vehicle with dipstick between
first and second exhaust tube, slide manifold into
position and start all bolts using lock washers
provided (lock and flat washers on slotted ends).
3. Re-attach dipstick to cylinder head using 1/4" bolt
and 1/2" long spacer tube provided.
4. Tighten all bolts at this time.
5. Raise vehicle.
6. Replace O2 sensor in left manifold and attach wires.
Replace O2 sensor in right manifold and attach wires.
7. Install extension pipes and start all bolts.
8. Replace O2 sensor in catalytic converter.
9. Tighten all bolts.
10. Lower vehicle and replace all spark plugs.
11. Replace all spark plug wires.
12. Check all hydraulic and fuel lines making sure there is
adequate clearance.
13. Replace air cleaner assembly and connect battery.
14. At this point, it would be a good idea to look everything
over and make sure nothing was missed in assembly.
15. Start vehicle and bring up to normal operating
temperature and check for possible leaks.
16. Turn engine off and let cool. Tighten all bolts again.
Catalog #67082 (Ceramic-Coated)
Qty. Part # Description
❑125-9123 Header left side
❑125-9078 Header right side
❑125-9521 Extension pipe left side
❑125-9643 Y-pipe assembly
Catalog #67083 (Ti-Tech Coated)
Qty. Part # Description
❑125-9448 Header left side
❑125-9446 Header right side
❑125-9523 Extension pipe left side
❑125-9634 Y-pipe assembly
Catalog #67092 (Ceramic-Coated)
Qty. Part # Description
❑125-9113 Header left side
❑125-9078 Header right side
❑125-9523 Extension pipe left side
❑125-9634 Y-pipe assembly
Catalog #67093 (Ti-Tech Coated)
Qty. Description
❑1Flange connector #46-1060
❑1Dipstick spacer; 3/8” O.D. x 1/2”
❑2Manifold port gaskets
❑2Donut connector gaskets
❑1Catalytic converter flange gasket
❑12-1/4” U-muffler clamp
❑ 11 3/8”-16 x 1” Hex header bolts
❑11/4”-20 x 1” Heax header bolts
❑43/8”-16 x 2” Hex bolts
❑83/8” Flat washers
❑16 3/8” Lock washers
❑13/8” Ferry bolt
❑ 15/8” Spacer, 1.50” long
Parts Common to All Part Numbers
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Edelbrock Pièce automobile
Edelbrock
Edelbrock Honda 99-LATER Manuel du propriétaire
Edelbrock
Edelbrock 70404 Manuel utilisateur
Edelbrock
Edelbrock Performer 4754 Manuel utilisateur
Edelbrock
Edelbrock Russell 672500 Manuel utilisateur
Edelbrock
Edelbrock 15016 Manuel utilisateur
Edelbrock
Edelbrock 2281 Manuel utilisateur
Edelbrock
Edelbrock SBC Vortec 283-400 c.i.d. Chevy V8 Manuel utilisateur
Edelbrock
Edelbrock 15015 Manuel utilisateur
Edelbrock
Edelbrock 262-400 Manuel utilisateur
Edelbrock
Edelbrock 4742 Manuel utilisateur
Edelbrock
Edelbrock 94 Manuel utilisateur
Edelbrock
Edelbrock 5229 Manuel utilisateur
Edelbrock
Edelbrock 7798 Manuel utilisateur
Edelbrock
Edelbrock Russell R09320 Manuel utilisateur
Edelbrock
Edelbrock 70403 Manuel utilisateur
Edelbrock
Edelbrock 352-428 Manuel utilisateur
Edelbrock
Edelbrock 2005-2007 (R) Manuel utilisateur
Edelbrock
Edelbrock 2760 Manuel utilisateur
Edelbrock
Edelbrock 75284 Manuel utilisateur
Edelbrock
Edelbrock PERFORMER-PLUS 2182 Manuel utilisateur
Manuels Pièce automobile populaires d'autres marques
ICI
ICI Magnum FBM10DGN Manuel utilisateur
Volant Perfomance
Volant Perfomance 19435 Manuel utilisateur
BENDIX
BENDIX GEN 4 GEN 5 ABS Manuel utilisateur
Vintage Air
Vintage Air 571065 Manuel utilisateur
Rugged Ridge
Rugged Ridge 11503.13 Manuel utilisateur
BENDIX
BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur
