Edelbrock 5711 Manuel utilisateur

Brochure #63-5711

Rev. 8/07 - DA/mc

Page 1 of 2

Catalog #5711

Edelbrock Cat-back Exhaust System

Catalog #5711

for 2007-2008 1500 Standard, Extended, & Crew Cab with

Short Bed (New Body Style)

Pick-Up, 4.8L & 5.3L V8, 2 & 4 W/D

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new Cat-back Exhaust System. If you have any questions,

contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

Suggested Tools for Installation:

❑3/8" ratchet set with SAE and metric sockets ❑9/16” & 15mm wrench

❑Jackstands and jack ❑Liquid penetrant and rubber lubricant

DISASSEMBLY

1. Raise vehicle and support with proper jackstands for

the weight, leaving the suspension hanging.

2. Use caution around hot exhaust systems to avoid

burns.

3. Use penetrating oil on all nuts and bolts.

Note: Some GM Trucks have a brace bar attached to

the left and right side frame rails. Remove bolt and

swing bar out of the way during installation.

4. Remove the bolts and clamps from the system and

lubricate the rubber hangers.

5. Use a pry bar to pull the rubber isolators off of the

pipe hangers.

6. Remove the old system. In some cases, you will find

it easier to cut the overaxle pipe to remove it.

ASSEMBLY

1. Bolt I-Pipe to factory outlet flange (behind catalytic

converters). Install hanger clamp assembly #23-

4099 onto I-pipe and engage hanger bar into OE

isolator and snug the clamp. Note: Do not tighten

flange bolts at this time, (snug only).

2. Slip the muffler onto the intermediate pipe with a

3" band clamp on the front. Note: Inlet end of

muffler is marked. Snug the clamp so you can adjust

the system later.

3. Install a 3” band clamp onto the outlet of the muffler.

Slip the overaxle pipe into outlet of muffler.

4. Install hanger clamp assembly #23-4100 behind

band clamp and engage into OE isolator. Install

hanger clamp assembly #23-4042 onto outlet end of

overaxle pipe and engage into OE isolator. Snug

clamps for adjustments later.

5. Slip tailpipe onto overaxle pipe, and install 3” band

clamp.

6. Working from the front of the system, align and

tighten each pipe from the cat-back.

7. Check for clearance to body, frame, suspension and

driveline as you tighten the system from front to rear.

8. Re-attach the brace bar to frame rail (if equipped).

9. Check for leaks and correct, if any are found.

WARNING!!!

Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

Brochure #63-5711

Rev. 8/07 - DA/mc

Page 2 of 2

Catalog #5711

KIT CONTENTS

WARNING: Support your vehicle with proper

jackstands or ramps rated for the total vehicle weight.

Place stands so that the rear axle is allowed to hang

free for easy system removal.

WARNING: These cat-back systems are engineered

to fit stock catalytic converters or equivalent

replacements. If you original system has been

modified, Edelbrock will not warranty fit or

performance.

Intermediate Pipe

Assembly

Muffler

Tailpipe

Assembly

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: (800) 416-8628

E-Mail: [email protected]

Hanger Clamps

Overaxle Pipe

Qty. Part # Description

❑125-3282 I-Pipe Extended & Crew Cab

❑125-3295 I-Pipe Standard Cab

❑125-3166 Overaxle Pipe

❑125-3157 Tail Pipe

❑1 25-55725 Muffler

Qty. Part # Description

❑2 46-6613 3” Band Clamps

❑1 23-4099 Hanger / Clamp Assembly

❑1 23-4042 Hanger / Clamp Assembly

❑1 23-4100 Hanger / Clamp Assembly

Table des matières

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock Russell R09392S Manuel utilisateur

Edelbrock

Edelbrock 7880 Manuel utilisateur

Edelbrock

Edelbrock 7577 Manuel utilisateur

Edelbrock

Edelbrock 6661 Manuel utilisateur

Edelbrock

Edelbrock 2925 Manuel utilisateur

Edelbrock

Edelbrock 71852 Manuel utilisateur

Edelbrock

Edelbrock 6879 Manuel utilisateur

Edelbrock

Edelbrock 5682 Manuel utilisateur

Edelbrock

Edelbrock 72000 Manuel utilisateur

Edelbrock

Edelbrock 15008 Manuel utilisateur

Edelbrock

Edelbrock 6893 Manuel utilisateur

Edelbrock

Edelbrock 73827 Manuel utilisateur

Edelbrock

Edelbrock 5204 Manuel utilisateur

Edelbrock

Edelbrock 25-9213 Manuel utilisateur

Edelbrock

Edelbrock 8126 Manuel utilisateur

Edelbrock

Edelbrock Chevrolet/GMC Trucks 454 SS Manuel utilisateur

Edelbrock

Edelbrock 6607 Manuel utilisateur

Edelbrock

Edelbrock 6502 Manuel utilisateur

Edelbrock

Edelbrock 6692 Manuel utilisateur

Edelbrock

Edelbrock 63-0081 Manuel utilisateur

Edelbrock

Edelbrock 5724 Manuel utilisateur

Edelbrock

Edelbrock Russell 641550 Manuel utilisateur

Edelbrock

Edelbrock PERFORMER RPM 60549* Manuel utilisateur

Edelbrock

Edelbrock 5728 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur