Edelbrock 5213 Manuel utilisateur

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 1 of 2

Edelbrock Anti-Hop Bars

for 1964-1972 GM A-Body (Catalog #5213)

& 1978-1987 GM A/G Body (Catalog #5214)

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new anti-hop bars. If you have any questions, contact our

Technical Hotline at: 1-800-416-8628, 7 am to 5 pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

Tools and Supplies Required:

❑ Jackstands ❑Torque Wrench (70 lb. min.)

❑Tire Chocks ❑Drill Motor

❑1/4” Drill Bit ❑Grease Gun

❑Floor Jack ❑Thread Lock Compound

❑7/16” & 3/4” Sockets and Wrenches

Caution: Installation requires being under raised vehicle. Support vehicle on level and stable ground using proper load

rated stands.

Note: Differential fill plug will not be accessible after installation. Check/change differential fluid before installation. The

right anti-hop will have to be removed to check fluid. After install, a fill plug style rear cover could be added.

1. Place vehicle on level stable ground (i.e. concrete or driveway). Chock front wheels at front and rear of tire

(Fig.1).

2. Raise rear of vehicle and support so to keep rear suspension loaded with vehicle weight. Removing rear tires is not

required but can be helpful.

3. During installation it is critical to maintain pinion angle. To do this, use floor jack to support pinion area of rear end

housing. NOTE: An angle finder can be used to measure pinion angle.

4. Remove left upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way. On 1978-1987 A/G cars, remove brake line distribution block bolt.

5. Remove pressed-in O.E.M. rubber bushing with caution so as to not damage rear end housing.

6. Install left anti-hop bar with grease fitting facing rear of vehicle. (Left bar in #5213 will be stamped with #25-4027

and #5214 will be stamped with #25-4038). Minor moving of brake line may be required on some years and models.

On #5214 use 5/16” bolt, nut and bracket to relocate line

(Fig. 2).

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

Fig. 1 Fig. 2

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

E-Mail: [email protected]

7. Locate anti-hop bar on steel bushing and 1/2"

(Fig. 3)

snug at this time.

8. Install upper trailing arm on anti-hop bar urethane bushing.

9. Drill 1/4" hole through axle housing web using anti-hop bar as guide. NOTE: Make sure to have at minimum 1/4" of

material between bolt hole and web edge,

(Fig. 2).

10. Install 1/4" bolt, washer and nyloc nut. Tighten bolt to 20 ft/lbs.

11. Use thread lock compound on upper trailing arm and steel bushing bolts and torque to 70 ft/lbs.

12. Remove right upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way.

13. Remove pressed in O.E.M. rubber bushing with caution so as to not damage rear end housing.

14. Install right anti-hop bar with grease fitting facing rear of vehicle. (Right bar in #5213 is marked #25-4028, #5214 is

marked #25-4039).

15. Locate anti-hop bar on steel bushing and 1/2 bolt

(Fig. 3)

, snug at this

time.

16. Install upper trailing arm on anti-hop bar urethane bushing.

17. Drill 1/4" hole through axle housing web using anti-hop bar as guide.

NOTE: Make sure to have minimum of 1/4" of material between bolt hole

and web edge.

18. Install 1/4" bolt, washer and nyloc nut torque to 10 ft/lbs.

19. Use thread lock compound on upper trailing arm and steel bushing bolts

and torque to 70 ft/lbs.

20. Although Edelbrock anti-hop bar bushings are prelubed, you may want to lub the bushings. Install zerk fitting covers

to prevent dirt and corrosion of the zerk fittings.

Check hardware tightness after 10 miles and on a regular basis.

Note: To further upgrade your suspension, use other Edelbrock suspension, springs and shocks. See an Edelbrock

dealer or go to our website at www.edelbrock.com.

Fig. 3

Steel Bushing

and Bolt

Grind here,

if needed.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Edelbrock Pièce automobile

Edelbrock

Edelbrock 4737 Manuel utilisateur

Edelbrock

Edelbrock 460 Ford Manuel utilisateur

Edelbrock

Edelbrock Performer 70011 Manuel technique

Edelbrock

Edelbrock 3530 Manuel utilisateur

Edelbrock

Edelbrock 68003 Manuel utilisateur

Edelbrock

Edelbrock Intake Manifolds Guide d'application

Edelbrock

Edelbrock 5756 Manuel utilisateur

Edelbrock

Edelbrock Chevrolet 5783 Manuel utilisateur

Edelbrock

Edelbrock 5758 Manuel utilisateur

Edelbrock

Edelbrock Honda TRX450R Manuel du propriétaire

Edelbrock

Edelbrock 5674 Manuel utilisateur

Edelbrock

Edelbrock 68452 Manuel utilisateur

Edelbrock

Edelbrock Honda XR400 Manuel du propriétaire

Edelbrock

Edelbrock 5.7L V8 Manuel utilisateur

Edelbrock

Edelbrock 5694 (Stainless Steel) Manuel utilisateur

Edelbrock

Edelbrock 1803 Manuel utilisateur

Edelbrock

Edelbrock Water Pump Gasket Kit 7522 Manuel utilisateur

Edelbrock

Edelbrock 2980 Manuel utilisateur

Edelbrock

Edelbrock PERFORMER-PLUS 2167 Manuel utilisateur

Edelbrock

Edelbrock 70080 Manuel utilisateur

Edelbrock

Edelbrock 66592 Manuel utilisateur

Edelbrock

Edelbrock 6893 Manuel utilisateur

Edelbrock

Edelbrock 70401 Manuel utilisateur

Edelbrock

Edelbrock 5786 Manuel utilisateur

Manuels Pièce automobile populaires d'autres marques

Dakota Digital

Dakota Digital 650277 Manuel utilisateur

bosal

bosal 037031 Manuel utilisateur

Vintage Air

Vintage Air 571063 Manuel utilisateur

GFB

GFB EX38 Manuel utilisateur

bosal

bosal 028091 Manuel utilisateur

Dodge

Dodge 8W-43 Guide de démarrage rapide

ICI

ICI Magnum FBM10DGN Manuel utilisateur

Volant Perfomance

Volant Perfomance 19435 Manuel utilisateur

BENDIX

BENDIX GEN 4 GEN 5 ABS Manuel utilisateur

Vintage Air

Vintage Air 571065 Manuel utilisateur

Rugged Ridge

Rugged Ridge 11503.13 Manuel utilisateur

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manuel utilisateur

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Mode d’emploi

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manuel utilisateur

Toshiba

Toshiba 48-1250 A Manuel utilisateur

aldes

aldes EHT2 Manuel utilisateur

Go Rhino

Go Rhino 24371T Manuel utilisateur

BBK

BBK 18950 Manuel utilisateur