Edc SM-7204 Manuel utilisateur

USER’S GUIDE

HAZ-DUST SM-7204™

REAL-TIME PERSONAL SILICA

MONITOR

MODEL SM-7204

DOC# HD7024 0621

Environmental Devices Corporation

Fieldstone Industrial Park

4 Wilder Drive Bldg. # 15

Plaistow, NH 03865

USA

Phone: (603) 378-2112

(800) 234-2589

Fax: (603) 378-2113

E-mail: [email protected]

Website: www.hazdust.com

SM-7204™

User’s Guide

Licenses, Copyrights and Trademarks

This documentation contains trade secrets and confidential information proprietary to Environmental

Devices Corporation (EDC). The software supplied with the instrumentation, documentation and any

information contained therein may not be used, duplicated or disclosed to anyone, in whole or in part,

other than as authorized in a fully executed EDC End User License or with the express written

permission of EDC.

HAZ-DUST™is a registered trademark of Environmental Devices Corporation. Other trademarks are

the property of their respective holders.

Safety Notice

Repair of instrumentation supplied by Environmental Devices Corporation (EDC) should only be

attempted by properly trained service personnel, and should only be conducted in accordance with the

EDC system documentation. Do not tamper with this hardware. High voltages may be present in all

instrument enclosures. Use established safety precautions when working with this instrument.

The seller cannot foresee all possible modes of operation in which the user may attempt to utilize this

instrumentation. The user assumes all liability associated with the use of this instrumentation. The

seller further disclaims any responsibility for consequential damages.

Warranty

Products manufactured by Environmental Devices Corporation (EDC) are warranted against defects

and workmanship for a period of one year from shipping date of original order to original purchaser at

the original ship to address. An additional extended warranty is available for an additional year and

follows the same terms and conditions. Any products or parts found defective by Environmental

Devices Corp. within the stated warranty period will be replaced or repaired at EDC’s discretion.

The warranty includes only instruments used in the manner the manufacturer (EDC) intended. The

warranty does not cover misuse, negligence, accidents, acts of God, damage from shipping, incorrect

cleaning and/or maintenance, unauthorized repairs, or any alterations and/or modifications including

hardware, software, and consumables preformed outside of the manufacture’s facility.

Consumables and expendables are not covered under the manufactures warranty. Common examples

include, gas scrubbers, filters, O-rings, and batteries. Batteries will be covered for 90 days from ship

date.

Modification of products or parts performed by any other person or entity other than EDC will void

warranty.

If a repair or replacement is desired, communication with our technical support staff regarding any

products or parts believed to be under warranty is mandated. Once communication is made a Return

Merchandise Authorization number will be issued.

Products not manufactured by us are subject to the vendor/manufactures warranty policy.

Products manufactured and returned to EDC are subject to a 25% restocking fee.

Shipping to the factory is paid by the customer. EDC will assume shipping charges for all warranty

repairs/replacements on the return to the original ship to address stated on initial Purchase Order

issued to EDC when allocating equipment.

All returning equipment must be decontaminated of any harmful substances.

Any replacement parts will be warranted for 90 days from shipping date and the same terms and

conditions as above apply.

5 
 
Table of Contents 
1. Section One.....................................................................................................................................................8 
Sections 1- Introduction to the SM-7204............................................................................................................9 
Introduction to the SM-7204 ............................................................................................................................10 
Real Time Dust Monitoring Principles...............................................................................................................11 
Overview of the SM-7204 .................................................................................................................................12 
Features of the SM-7204 ..................................................................................................................................14 
Specifications of the SM-7204 ..........................................................................................................................16 
Components of the SM-7204............................................................................................................................17 
2. Section Two...................................................................................................................................................18 
Section 2- Operating Parameters of the SM-7204............................................................................................19 
Turning the SM-7204 ON and OFF....................................................................................................................20 
Using the Menu.................................................................................................................................................21 
Creating Unique Aerosol Profiles......................................................................................................................23 
Cross Calibration ...............................................................................................................................................24 
Selecting Language ...........................................................................................................................................25 
Setting the Alarm ..............................................................................................................................................26 
Setting Date and Time.......................................................................................................................................28 
Setting Log Rate ................................................................................................................................................30 
Data Recording..................................................................................................................................................31 
Data Management ............................................................................................................................................32 
About Screen.....................................................................................................................................................34 
3. Section Three ................................................................................................................................................35 
Section 3- Operating the SM-7204 ...................................................................................................................36 
Connecting Sensor ............................................................................................................................................37 
Selecting the Particle Size .................................................................................................................................38 
Particulate Selection .........................................................................................................................................39 
Thoracic Dust Particulates ................................................................................................................................40 
Respirable Dust Particulates .............................................................................................................................41 
Inhalable Dust Particulates ...............................................................................................................................42 
Flow Rate ..........................................................................................................................................................45 
Zero Calibration ................................................................................................................................................48 
Sampling Procedure..........................................................................................................................................50 

6 
 
Real-Time Data Viewing....................................................................................................................................51 
Stop Run............................................................................................................................................................52 
Infield Calibration Verification..........................................................................................................................53 
Faults.................................................................................................................................................................55 
Reviewing Stored Data......................................................................................................................................56 
Uploading Data .................................................................................................................................................57 
Live Feed ...........................................................................................................................................................58 
4. Section Four ..................................................................................................................................................60 
Section 4- Using DustComm Pro Software........................................................................................................61 
Introduction to the DustComm Pro Software...................................................................................................62 
Installing DustComm Pro Software...................................................................................................................63 
Loading DustComm Pro Software.....................................................................................................................64 
Menu Selections................................................................................................................................................65 
File Menu Commands .......................................................................................................................................66 
Downloading Data.............................................................................................................................................67 
DustComm Pro Windows..................................................................................................................................69 
Translating Data to an ASCII Text File ...............................................................................................................71 
Generating a Plot ..............................................................................................................................................72 
Data Plot Menu Selections................................................................................................................................73 
Editing Title .......................................................................................................................................................75 
Applying a Correction Factor ............................................................................................................................76 
Inability to Download Data to PC......................................................................................................................77 
5. Section Five ...................................................................................................................................................78 
Section 5- Maintenance on SM-7204................................................................................................................79 
Checking the Calibration Span ..........................................................................................................................80 
Battery Maintenance ........................................................................................................................................82 
Cleaning Sensor Optics......................................................................................................................................84 
Cleaning Sensor Optics......................................................................................................................................84 
Appendix ...............................................................................................................................................................84 
Appendix A........................................................................................................................................................84 
Appendix B ........................................................................................................................................................84 
Appendix C ........................................................................................................................................................84 
Appendix D........................................................................................................................................................84 

1. Section One

Introduction to the SM-7204

Introduction

This section introduces and describes the SM-7204. It Explains operating principles of the SM-7204

and identifies features, specifications and components of SM-7204.

This section contains the following topics.

•Introduction to the SM-7204……………....Page 10

•Real-Time Dust Monitoring Principles…....Page 11

•Overview of the SM-7204…........................Page 12

•Features…………………………………....Page 14

•Specifications………………………….......Page 16

•Components…………………………….....Page 17

Sections 1- Introduction to the SM-7204

Introduction

The SM-7204 is the world’s first personal dust monitor to combine traditional filter techniques with

real-time monitoring methods. These techniques combine to overcome limitations of all other dust

monitoring products.

Dust Monitoring Methods

Figure 1-1. Diagram showing components used for both the traditional and real-time dust monitoring methods.

Real Time Dust

Monitor

Traditional Filter

Gravimetric Dust

Measurement

Filter Cassette

Sensor Head

Introduction to the SM-7204

Table des matières

Autres manuels edc Instrument de mesure

edc

edc RD400P Manuel utilisateur

edc

edc HAZ-DUST IV HD-1004-S Manuel utilisateur

edc

edc MU300 Manuel utilisateur

edc

edc HAZ-DUST HD-7204 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur

edc SM-7204 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques