Ecotech Serinus 51 Manuel utilisateur
Serinus 51
SO
2
/H
2
S Analyzer
User Manual
Version: 1.0
July 2011
Tel: (+61) 1300 364 946. Fax: (+61) 1300 668 763.
E-mail: [email protected]
Address: Australia - Head Office
1492 Ferntree Gully rd Knoxfield Victoria, 3180, Australia
Serinus 51 User manual 1.0 Front Matter
i
Manufacturers statement
Thank you for selecting the Ecotech Serinus 51 Sulfur Dioxide Analyzer.
The Serinus series is the next generation of Ecotech designed and manufactured gas
analyzer, the Serinus 51 will perform Sulfur Dioxide measurements over a range of 0-
2ppm with an LDL of 0.5 ppb.
This User Manual provides a complete product description including operating
instructions, calibration, and maintenance requirements for the Serinus 51.
Reference should also be made to the relevant local standards, which should be used
in conjunction with this manual. Some relevant standards are listed in the References
section of this manual.
If, after reading this manual you have any questions or you are still unsure or unclear
on any part of the Serinus 51 then please do not hesitate to contact Ecotech or your
local Ecotech distributor.
Ecotech also welcomes any improvements that you feel would make this a more
useable and helpful product then please send your suggestions to us here at Ecotech.
Please help the environment and recycle the
pages of this manual when finished using it.
Notice
The information contained in this manual is subject to change without notice. Ecotech
reserves the right to make changes to equipment construction, design, specifications
and /or procedures without notice.
Copyright © 2011. All rights reserved. Reproduction of this manual, in any form,
is prohibited without the written consent of Ecotech Pty Ltd.
Front Matter Serinus 51 User manual 1.0
ii
WARNING
Hazardous voltages exist within the analyzer. The analyzer lid should be closed and
quarter turn lid fasteners locked when the analyzer is left unattended or turned on.
Ensure the power cord, plugs and sockets are maintained in a safe working condition
and lid is closed and screw is fastened in place.
Safety requirements
•To reduce the risk of personal injury caused by electrical shock, follow all
safety notices and warnings in this documentation.
•If the equipment is used for purposes not specified by Ecotech, the protection
provided by this equipment may be impaired.
•Replacement of any part should only be carried out by qualified personnel,
using only parts specified by Ecotech as these parts meet stringent Ecotech
quality assurance standards. Always disconnect power source before removing
or replacing any components.
Serinus 51 User manual 1.0 Front Matter
iii
Factory service/warranty
This product has been manufactured in an ISO 9001/ISO 14000 facility with care and
attention to quality.
The product is subject to a 12-month warranty on parts and labor from date of
shipment (the warranty period). The warranty period commences when the product is
shipped from the factory. Lamps, fuses, batteries and consumable items are not
covered by this warranty.
Each analyzer is subjected to a vigorous testing procedure prior to dispatch and will
be accompanied with a parameter list and a multipoint calibration check thereby
enabling the analyzer to be installed and ready for use without any further testing.
To ensure that we process your factory repairs and returned goods efficiently and
expeditiously, we need your help. Before you ship any equipment to our factory,
please call your local Ecotech service response centre (or distributor) to obtain a
return authorization number.
When you contact Ecotech please provide the following information:
1. your name, telephone number and Facsimile number
2. Your company name
3. The model number or a description of each item
4. The serial number of each item, if applicable
5. A description of the problem or the reason you are returning the equipment
(e.g. sales return, warranty return, calibration, etc)
If you are required to return the equipment an accompanying document with:
1. Your name, number and Facsimile number
2. Your company name with return shipment
3. The model number or a description of each item
4. The serial number of each item, if applicable
A description of the problem/reason you are returning the equipment
Front Matter Serinus 51 User manual 1.0
iv
CE Mark Declaration of Conformity
This declaration applies to the Serinus 51 SO
2
analyzers as manufactured by Ecotech Pty. Ltd. of 1492
Ferntree Gully Rd, Knoxfield, VIC, 3180, Australia, and which may be sold in the following
configurations:
To which this declaration relates is in conformity with the following European Union Directives:
Council Directive of 15 December 2004 on the approximation of the laws of Member
States relating to electromagnetic compatibility (2004/108/EC)
The following standard was applied:
EN 61326-1:2006 Electrical Equipment for measurement, control and
laboratory use – EMC Requirements – Part 1: General
requirements.
•Immunity Requirements EN61326-1
IEC-61000-4-2 Electrostatic discharge immunity
IEC-61000-4-3 Radiated RF immunity
IEC-61000-4-4 Electrical fast transient burst immunity
IEC-61000-4-5 Surge immunity
IEC-61000-4-6 Conducted RF Immunity
IEC-61000-4-11 Voltage dips and interruption immunity
•Electromagnetic compatibility EN61326-1
CISPR-11 Radiated RF emission measurements
CISPR-11 Mains Terminal RF emission measurements
IEC-61000-3-3 Mains Terminal voltage fluctuation measurements
IEC-61000-3-2 Power Frequency harmonic measurements
Council Directive of 12 December 2006 on the harmonization of the laws of Member
States relating to electrical equipment designed for use within certain voltage limits
(2006/95/EC)
The following standard was applied:
EN 61010-1:2001 Safety requirements for electrical equipment, for
measurement control and laboratory use – Part 1:
General requirements
•For protection against:
Electric shock or burn
Mechanical HAZARDS
Excessive temperature
Spread of fire from the equipment
Effects of radiation, including laser sources and sonic and ultrasonic
pressure
Serinus 51 User manual 1.0 Front Matter
v
Claims for Damaged Shipments and
Shipping Discrepancies
Damaged shipments
1. Inspect all instruments thoroughly on receipt. Check materials in the
container(s) against the enclosed packing list. If the contents are damaged
and/or the instrument fails to operate properly, notify the carrier and Ecotech
immediately.
2. The following documents are necessary to support claims:
a. Original freight bill and bill lading
b. Original invoice or photocopy of original invoice
c. Copy of packing list
d. Photographs of damaged equipment and container
e. Contact you freight forwarder for insurance claims
You may want to keep a copy of these documents for your records also.
Refer to the instrument name, model number, serial number, sales order
number, and your purchase order number on all claims. Upon receipt of a
claim, we will advice you of the disposition of your equipment for repair or
replacement.
Shipping Discrepancies
Check all containers against the packing list immediately on receipt. If a shortage or
other discrepancy is found, notify the carrier and Ecotech immediately. We will not be
responsible for shortages against the packing list unless they are reported promptly
(within 7 days).
Front Matter Serinus 51 User manual 1.0
vi
Internationally recognized symbols used
on Ecotech Equipment
Electrical fuse IEC 60417-5016
Earth (ground) terminal IEC 60417-5017
Protective conductor terminal IEC 60417-5017
Equipotentiality IEC 60417-5021
Alternating current IEC 60417-5032
Caution, hot surface IEC 60417-5041
Caution, risk of danger. Refer
to accompanying documents
ISO 7000-0434
Caution, risk of electric shock
ISO 3864-5036
Serinus 51 User manual 1.0 Front Matter
vii
Front Matter Serinus 51 User manual 1.0
viii
Manual Revision History
Ecotech Manual ID: MAN 0080
Manual PN: M010040
Current Revision: 1.0
Date released: July 2011
Description: User Manual for the Serinus 51 SO
2
/H
2
S analyzer
This manual is the full user manual for the Serinus 51 SO
2
/H
2
S analyzer. This manual
contains all relevant information on theory, specifications, installation, operation,
maintenance, calibration, communication and troubleshooting. Any information that
cannot be found within this manual can be found by contacting Ecotech at:
Phone: +61 1300 364 946
Fax: +61 1300 668 763
Address: Ecotech Pty Ltd
1492 Ferntree Gully Rd
Knoxfield Victoria
Australia 3180
Website www.ecotech.com
Edition
Date Summary Pages
1.0 July 2011 Initial release all
Table des matières
Autres manuels Ecotech Instrument de mesure
Ecotech
Ecotech Serinus 40 Manuel utilisateur
Ecotech
Ecotech HiVol 3000 Manuel utilisateur
Ecotech
Ecotech A Series Manuel utilisateur
Ecotech
Ecotech Serinus 30 Manuel utilisateur
Ecotech
Ecotech Acoem Serinus 30 Manuel utilisateur
Ecotech
Ecotech Acoem Serinus 10 Manuel utilisateur
Ecotech
Ecotech Serinus 44 Manuel utilisateur
Ecotech
Ecotech Serinus 57 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur